Snapper ZMT2500KH, ZM5201M, ZM6101M Operating Instructions, PRE-START Check List

Page 6

Section 2 - OPERATING INSTRUCTIONS

2.1PRE-START CHECK LIST

Make the following checks and perform the service required before each start-up.

2.1.1.Check tires and add or release air as needed to bring pressure to 12 psi in drive tires. Pressure in front deck caster wheels should be 25 psi.

2.1.2.Check guards, deflectors and covers to make sure all are in place and securely tightened.

2.1.3.Check engine oil and add oil as needed to bring level up to the FULL mark. Refer to engine owner’s manual for oil specifications. See Figure 2.1.

SAFE LEVEL

AREA

FIGURE 2.1

2.1.4.Check Blade switch to insure it works freely. Switch is pulled “OUT” for blade engagement or pushed back “IN” for blade disengagement. See Figure 2.2. IMPORTANT: Disengagement stops blades.

BLADE SWITCH

FIGURE 2.2

2.1.5.Clean exterior surfaces of cutting deck and engine of any accumulation of dirt, grass, oil, etc. Keep engine air intake screen and cooling fins clear at all times.

2.1.6.Add fuel to tank of the machine outside where fumes can safely dissipate. Make sure fuel filler cap is tight. Refer to engine owner’s manual for fuel specifications.

2.1.7.Adjust position of operator’s seat. The seat is mounted on slides. Locate latch lever beneath the seat. Move lever towards the left and slide seat to the desired position. Release latch.

2.1.8.Place mower in desired cutting height setting. Grasp deck lift lever and depress release button located at tip of lever. Move lever to desired setting, 1 thru 7, and release latch. See Figure 1.1.

IMPORTANT: This machine is equipped with hydrostatic drive. The direction of motion and the speed of motion is controlled by the left and right motion control levers. A small movement of these controls can cause the machine to move instantly. DO NOT attempt to operate the machine until you read this manual and become familiar with it’s operation. Practice with the blades “OFF” disengaged, engine speed at a slow setting and in an open area away from obstacles.

ROLL RELEASE: To roll the machine without the engine running, pressure within the hydraulic pumps must be released. There is one lever on the upper right side of each pump that is used to release the pressure. Rotate lever counter clockwise and secure in that position. See Figure 2.3

HYDRAULIC PRESSURE

RELEASE LEVER IN “RUN”

POSITION

LEVER SHOWN LOCKED

INTO “ROLL” POSITION

FIGURE 2.3

6

Image 6
Contents Model Number Explanation Mower UnitProtection for Children Protection Against TipoversPreparation Maintenance OperationMount and dismount machine from left side Table of Contents Introduction NomenclatureOperating Instructions PRE-START Check ListStopping Engine Starting & Stopping ENGINE, BLADES, Parking BrakeStarting Engine Starting Mower BladesParking Brake Cutting Height Adjustment OPERATION- Motion Controls 2.4.1. Driving MachineStopping Machine Service After First 5 Hours Change Engine OILCheck Mower Blade After Every 25 Operating Hours 3.3.1. Engine Other Lubrication Points Before Operating MachineAnnually END of Each Season Annually END of Each Season from previous Fuel FilterDeck Removal Power Transfer Shaft Removal Deck Removal from previousNeutral Position Adjustments Side to Side LevelMower Deck Adjustment Levelness Front to Rear LevelParking Brake Adjustment Engine Adjustments & RepairMower Blade Replacement 4.5.1. Blade Wear Limits Blade Sharpening Mower Drive Belt ReplacementBelt Replacement Belt RemovalBattery Battery Removal Battery InstallationBattery Service Battery Testing NEW Battery Preparation 1. Remove battery from cartonDo not Overfill Problem Probable Cause Corrective Action Trouble Shooting on NextTractor Will Not Move MAINTENANCE/REPLACEMENT Parts MAINTENANCE/REPLACEMENT Parts Mower DeckService Performed Each 100Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Page Page Page MID Mount Z-RIDER Zero Turning Hydro Drive Series