Dynacord DPA 4120, DPA 4140 NRS 90208 input transformer for the floating, balanced input

Page 33

The remote module allows to remotely control and monitor the operation of the power amplifiers DPA 4120 and DPA 4140 from the PROMATRIX manager DPM 4000 (for further details please refer to the PROMATRIX handbook).

Caution: Before installing the input module NRS 90222, you have to unplug the mains connector as well as a presumably connected battery cord.

Before installing the input module, it is necessary to remove the two locking screws B on the rear panel of the appliance. For installation the printed board assembly first has to be inserted into the guiding rails. After carefully pushing the module in it has to be locked by using the two screws mentioned before.

Note After installing the remote module NRS 90222 it is necessary to set its address according to the description in the PROMATRIX handbook using the two "HEX-code switches" ADDRESS (21) and note the setting within the field ADDRESS on the rear panel of the appliance using a waterproof marker pen.

8.3NRS 90208 input transformer for the floating, balanced input

For the case that floating inputs are required, the inputs of the INPUT MODULE NRS 90225 and the REMOTE MODULE NRS 90222 are prepared for retrofitting input transformers. If so, it is necessary to additionally install the extension kit NRS 90208 per each input.

The installation has to be performed as follows (see figure 6 and/or figure 7):

-to remove the input module you have to loosen the two locking screws (B) on the rear panel of the appliance. Now, the module can be easily torn out.

-before installing the input transformer you have to remove the resistors R1 and R2.

-mount the input transformer onto the printed board assembly, so that the marking located on the connector side of the transformer matches with the one on the printed board assembly. To prevent short-circuits place the supplied insulation disc between the transformer and the printed board assembly.

-re-insert the input module and tighten the locking screws (B).

8.4NRS 90227 output transformer for the floating, balanced monitor output

In case that floating monitor outputs are required, the outputs of the INPUT MODULE NRS 90225 and REMOTE MODULE NRS 90222 are prepared for retrofitting output transformers. If so, it is necessary to additionally install the extension kit NRS 90227 per each output.

The installation has to be performed as follows (see figure 6 and/or figure 7):

-to remove the input module you have to loosen the two locking screws (B) on the rear panel of the appliance. Now, the module can be easily torn out.

-before installing the output transformer you have to remove the resistors R22, R23, R32 and R33 (NRS 90225) respectively the resistors R23, R24, R71 and R72 (NRS 90222).

-now, you can mount the output transformer onto the printed board assembly. Because of the transformer's symmetrical design, polarity is not a critical factor.

-re-insert the input module and tighten the locking screws (B).

33

Image 33
Contents Leistungsmerkmale Power Amplifier DPA 4120 / DPA+7,*6,&+5+,76+,1,6 DPA Anzeigen, Bedienungselemente und AnschlüsseInhaltsverzeichnis Verwendung InstallationshinweiseDer Verstärker ist zu schützen vor Vor der InbetriebnahmeEingang Input Batteriebetrieb 24V DCAusgänge Leistungsausgang Power Output Steueranschluß Remote Control nur NRS Leistungsausgang Power Output für niederohmige LautsprecherKontrollausgang Monitor Anzeigen STANDBY-AnzeigeGround Fault Anzeige Protect AnzeigeAussteuerungskontrolle und CLIP-Anzeige Remote Modul NRS Der Einbau ist wie folgt vorzunehmen siehe Bild 6 bzw. Bild Input Transformer NRS Output Transformer NRS Pilotton-Überwachung Pilotton & Erdschluß Überwachung NRSErdschluß-Überwachung Der Einbau ist wie folgt vorzunehmen siehe Bild 8 bzw. BildNRS 90 406 S 411 Prüfung der Funktion Pilotton-Überwachung Prüfung der Funktion Erdschluß-Überwachung Groundlift Schalter Circuit a to Chassis SwitchEinbau in 19-Gehäuse oder 19-Gestellschränke Sicherungen Sicherungen in DPA503 F Page Page Eigenschaften des Eingangs BatteriebetriebEigenschaften des Leistungs-Ausgangs Eigenschaften des Monitor-AusgangsNachrüstsätze für DPA 4120 und DPA Erdschluß Überwachung Performance Features 03257$176$7,16758&7,216 12 a Indicators, controls and connectionsContents Utilization InstallationAmplifier has to be protected from Before the first operationInput Battery operation 24V DCPower Output for low impedance loudspeaker systems Power Output for 100V 70V or 50V loudspeaker systemsOutputs Single Call and obligatory reception relays Override BypassIndicators Standby indicator Remote Control connector only NRSReady indicator Protect indicatorLevel meter and Clip indicator Remote module NRS Enhanced application field Standard input module NRSNRS 90208 input transformer for the floating, balanced input Input Transformer NRS Output Transformer NRS NRS 90224 pilot tone & ground fault surveillance Ground fault surveillancePilot tone surveillance NRS 90 406 S 411 Checking the pilot tone surveillance function Case and 19-rack-shelf system installation Checking the ground fault surveillance functionGround lift switch Circuit a to Chassis Switch Fuses Fuses in the DPA503 F 503 F 601 602 Features of the input nominal input level Battery operationExtension kits for the DPA 4120 and DPA DPA 4140 power amplifier 400 W power supply Mains operationNRS 90208 input transformer for floating, balanced input Caractéristiques techniques Amplificateur DE Puissance DPA 4120 / DPA16758&7,2166e&85,7e,03257$176 Témoins, contrôles et connexions NRS 90225 module dentrée général Lamplificateur doit être protégé contre UtilisationAvant la première utilisation Fonctionnement sur le secteurInput Entrée Fonctionnement sur batterie 24V DCSorties Câblage LF pour le couplage de deux amplificateurs DPASortie Monitor Connecteur Remote Control NRS 90225 uniquementTémoins Témoin Standby Témoin ReadyVumètre et témoin Clip Témoin Ground FaultChamps dapplications avancées Module dentrée standard NRS Module de télécommande NRSPage Input Transformer NRS Output Transformer NRS Surveillance de défaut de masse Surveillance de la fréquence piloteNRS 90 406 S 411 NRS 90 406 S 411 Installation en rack 19 et en armoire rack Commutateur de mise à la masse Circuit a to Chassis SwitchFusibles Fusibles du DPA 503 F 503 F 601 602 Caractéristiques de lentrée Fonctionnement sur batterieCaractéristiques de la sortie de puissance Caractéristiques de la sortie MonitorKits dextension pour les DPA 4120 et DPA Surveillance du défaut de masse entrée ligne haut-parleur Page Blockdiagram Page Page Page Bosch Communications Systems
Related manuals
Manual 23 pages 27.73 Kb

DPA 4120, DPA 4140 specifications

The Dynacord DPA 4120 and DPA 4140 are powerful amplifier solutions designed for professional audio applications. These models are ideal for live sound reinforcement, permanent installations, and various audio distribution requirements.

Both DPA 4120 and DPA 4140 are part of the Dynacord DPA series, which is renowned for delivering high-quality sound and reliability in demanding environments. The DPA 4120 provides a robust 1200 watts of power per channel at 4 ohms, while the DPA 4140 ups the ante with an impressive 1400 watts per channel at the same impedance, making them suitable for driving a wide range of speaker systems.

One of the standout features of both amplifiers is the incorporation of advanced DSP (Digital Signal Processing) technology. This technology offers precise control over sound performance, allowing users to tailor settings to meet specific venue acoustics or personal preferences. The DSP includes functions such as equalization, crossover adjustments, delay, and limiting, ensuring optimal sound delivery in any setting.

Durability is another hallmark of the Dynacord DPA series. The amplifiers feature a rugged, lightweight design, ideally suited for touring and rental companies. The internal architecture includes a sophisticated cooling system that allows for extended operation under high-demand conditions without overheating.

Both models are equipped with a range of connectivity options, including XLR inputs and Speakon outputs, facilitating seamless integration with various audio systems. The amplifiers support both analog and digital input sources, ensuring compatibility with modern audio setups.

In terms of sound quality, the DPA 4120 and DPA 4140 are engineered with low distortion levels and high efficiency, achieving high-performance audio output while maintaining clarity and detail across all frequencies. The amplifiers also feature a robust power supply that delivers consistent performance, even during peak use scenarios.

User-friendly controls and monitoring options are also inherent in the design of these amplifiers. An intuitive front panel interface allows for easy adjustment of settings, while LED indicators provide real-time feedback on performance and operational status.

In summary, the Dynacord DPA 4120 and DPA 4140 offer exceptional power, sound quality, and advanced features, making them excellent choices for audio professionals seeking reliable and powerful amplification solutions. Their combination of performance, durability, and versatility serves to meet the needs of various professional audio applications, solidifying their place in the competitive landscape of audio amplifiers.