Snapper ZF2101DKU, ZF5201M, ZF6101M, ZF2301GKU Fuel Filter Diesel Engine, Deck Removal

Page 18

Section 4 - MAINTENANCE

4.5ANNUALLY (END OF EACH SEASON) (Continued from previous Page)

4.5.2.FUEL FILTER (DIESEL ENGINE)

Service fuel filter as instructed in engine owner’s manual. Turn key to “OFF” position. Engine MUST be stopped and MUST be cold before removing filter.

1.Move the fuel filter cock handle to the closed position.

2.Remove the fuel filter bowl retaining ring. Fuel filter bowl, two “O” Rings, spring and filter can be removed. See Figure 4.8.

3.Replace filter element. Clean filter bowl with fresh diesel fuel. Reassemble the fuel filter bowl assembly. Tighten retaining ring securely. Check for leakage. Air bleed the fuel system.

4.Fill the fuel tank to the fullest extent. Open the fuel filter cock.

5.Loosen air vent plug a few turns at the top of fuel filter/fuel cock assembly. Allow air bubbles to be released. Close air vent plug when a steady flow of fuel is observed.

NOTE: After replacing fuel filter, engine may have to be cranked briefly with air vent plug loosened to purge all air from system.

4.6DECK REMOVAL

Move machine to an area where the mower deck is to be disconnected. Turn engine “OFF” but leave key switch in the “ON” position. Engage parking brake.

1.The rear of deck must be raised up and both jack stands moved down to the lowest position and both locking pins inserted. NOTE: Jack stands are stored on the left and right rear sides of the mower.

2.Using deck lift switch, lower deck down to rest on jack stands.

3.The hitch latch pins are shown in the latched position. The latched position locks the deck lift arm into position. See Figure 4.9.

HITCH LATCH PIN

SHOWN IN LATCHED

OR LOCKED

POSITION

AIR VENT PLUG

FUEL COCK

SMALL “O”

RING

FUEL FILTER

SPRING

LARGE “O”

RING

FUEL BOWL

RETAINING

RING

FIGURE 4.8

DECK

LIFT ARMHITCH

PLATE

FIGURE 4.9

(Continued on Next Page)

WARNING

Allow engine to cool for at least ten minutes before performing service or maintenance. DO NOT smoke near fuel components when performing service or maintenance. DO NOT perform service and maintenance near an open flame. Wipe off any spilled fuel before starting engine. DO NOT run engine indoors.

18

Image 18
Contents OUT Front Z-RIDER Hydro Drive Series Important Safety Instructions Operation Important Safety Instructions Table of Contents Introduction NomenclatureSafety Messages and Symbols Safety Messages and Symbols Keep Children and Others OUT of the Mowing Area Operating Instructions PRE-START Check ListStarting Engine Starting & Stopping ENGINE, Blades Parking BrakeStopping Engine Starting Mower BladeStopping Mower Blade Cutting Height Adjustment Operation Motion Control 3.3.1. Driving Machine Service After First 5 Hours Change Engine OILCheck Mower Blade Check Mower Drive Belt After Every 25 Operating HoursMower Components Riding Mower Lubrication Other Lubrication PointsBefore Operating Mower Fuel Filter Diesel Engine Deck RemovalPower Transfer Shaft Removal From PreviousAdjustments & Repair Neutral Position AdjustmentsParking Brake Adjustment Mower Blade Replacement Blade Wear Limits Blade SharpeningMower Drive Belt Removal Mower Drive BELT, Engine Belt & Hydro Pump Belt ReplacementMower Drive Belt Replacement Engine Belt RemovalBattery Battery Removal Battery InstallationBattery Service NEW Battery Preparation BatteryBattery Testing Do not OverfillRemove NUT Remove Belt From Spindle Remove Blade Bolt Troubleshooting Problem Probable Cause Corrective ActionProblem Probable Cause Corrective Action Service Schedule MAINTENANCE/REPLACEMENT PartsYear Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Page OUT Front Z-RIDER Hydro Drive Series