Snapper SB2000M Starting a Cold Engine, Starting a Warm Engine, Starting a Flooded Engine

Page 7

For Parts Call K&T 606-678-9623 or 606-561-4983

STARTING POSITION

Blower

Vacuum

WARNING: When starting engine, hold the unit as illustrated. Do not set unit on any surface except a clean, hard area when starting engine or while engine is running. Debris such as gravel, sand, dust, grass, etc. could be picked up by the air intake and thrown out through the discharge opening, damaging the unit or property, or causing serious injury to by- standers or the operator.

STARTING A COLD ENGINE

1.Move throttle lever to the position.

2.Move choke lever to the FULL CHOKE position.

3.Slowly press the primer button 8 times.

Throttle Lever

 

Primer Button

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Choke Lever

4.Pull starter rope sharply until engine at- tempts to run, but no more than5 pulls (be- low 30_ F, 8 pulls).

NOTE: If engine attempts to start before the 5th pull, go to next step immediately.

5.Move the choke lever to the HALF CHOKE position.

6.Pull the starter rope sharply until the en- gine runs, but no more than 5 pulls (below 30_ F, 10 pulls).

7.After a 5 second warm--up, move the choke lever to the RUN position.

8.Allow the unit to run for 30 more seconds at the RUN position before moving the

throttle lever to position.

If engine has not started after 5 pulls (at HALF CHOKE), repeat STARTING A COLD ENGINE procedure. If engine still does not start, proceed to STARTING A FLOODED ENGINE.

9.To stop the engine, move the throttle lever to the STOP position.

STARTING A WARM ENGINE

NOTE: If fuel tank is empty, add fuel; then, follow STARTING A COLD ENGINE proce- dure. Do not fill fuel tank while engine is hot.

1.Move throttle lever to the position.

2.Pull starter rope sharply until engine runs, but no more than 5 pulls.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

3.To stop the engine, move the throttle lever to the STOP position.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the RUN position. Move throttle

lever to the fast position

; then, pull rope

until engine starts. After engine starts, move the

throttle lever to the slow position to allow engine to idle.

Starting could require pulling the starter rope many times depending on how badly the unit is flooded.

If unit still doesn’t start refer to the TROUBLE- SHOOTING TABLE or call 1-800-554-6723.

WARNING: Avoid touching muffler unless engine and muffler are cold. A hot muffler can cause serious burns.

WARNING: Stop engine and be sure the impeller blades have stopped turning be- fore opening the vacuum inlet door or at- tempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. Always disconnect the spark plug before performing maintenance or ac- cessing movable parts.

GENERAL RECOMMENDATIONS

Thewarranty on this unit does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain unit as

instructed in this manual. Various adjust- ments will need to be made periodically to properly maintain your unit.

CHECK FOR LOOSE

FASTENERS AND PARTS

SSpark Plug Boot S Air Filter

S Housing Screws S Muffler

CHECK FOR DAMAGED OR WORN PARTS

Contact an authorized service dealer for re- placement of damaged or worn parts.

SFuel Tank -- Do not use unit if fuel tank shows

signs of damage or leaks.

SVacuum Bag -- Do not use vacuum bag if it is torn or damaged.

-- 7 --

www.mymowerparts.com

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Manual de Instrucciones Manuel d’Instructions Operate Your Unit Safely Know Your UnitPlan Ahead Handle Fuel with CAUTION, IT is Highly FlammableBlower Tube Assembly Vacuum BAG AssemblyMaintain Your Unit Properly Vacuum Vacuum Tube AssemblyHOW to Convert Unit from Vacuum USE to Blower USE Elbow Tube SmallPrimer Button Shoulder Strap AdjustmentKnow Your Blower Throttle LeverTo Stop the Engine Operating PositionOperating Tips Before Starting Engine Fueling EngineGeneral Recommendations Starting a Cold EngineStarting a Warm Engine Starting a Flooded EngineReplace Fuel Filter Inspect and Clean Unit and DecalsClean AIR Filter Carburetor AdjustmentsOther Troubleshooting Table EngineSeasonal Storage Fuel SystemLigations The U. S. Environmental Electrolux Home PRODUCTS, INCIntermediate 125 hours Extended 300 hours

SB2000M specifications

The Snapper SB2000M is a powerful and versatile lawn mower designed to make lawn care easier and more efficient for homeowners and landscaping professionals alike. With its robust features and innovative technologies, the SB2000M stands out in the competitive outdoor power equipment market.

One of the most notable features of the Snapper SB2000M is its reliable 190cc engine. This engine provides ample power to tackle even thick grass with ease. Its easy-to-start system ensures that users can quickly get to work without the hassle of complicated starting procedures. The durable steel cutting deck is designed for longevity, providing a perfect combination of strength and weight, enabling the mower to manage various terrains effectively.

The SB2000M comes equipped with a 21-inch cutting deck, which offers users the ability to cover large areas while still being maneuverable enough to navigate around obstacles such as flower beds and trees. The adjustable cutting height feature allows users to customize their lawn care experience with six different height settings, ranging from one to four inches. This feature ensures that homeowners can achieve their desired lawn appearance, whether they prefer a closely manicured look or a more natural finish.

In terms of technology, the Snapper SB2000M boasts an advanced rear-wheel drive system, which enhances its maneuverability. This drive system provides better traction while mowing on slopes and uneven ground, making it an ideal choice for varied landscapes. The self-propelling capability allows for less strain and effort, allowing users to mow larger areas with minimal fatigue.

Moreover, the Snapper SB2000M supports both mulching and bagging options, offering flexibility depending on user preferences and lawn care needs. The mulch plug enables grass clippings to be finely chopped and returned to the lawn, providing natural fertilization, while the rear bag can efficiently collect clippings for disposal or composting.

Safety features are also a priority with the SB2000M. The engine automatically shuts off when the operator releases the handle, minimizing risks associated with accidental operation. Additionally, the folding handlebar makes storage easier, reducing the amount of space needed when the mower is not in use.

In summary, the Snapper SB2000M is a feature-rich mower that combines power, agility, and user-friendly technology, making it an ideal choice for anyone looking to maintain their lawn effectively. With its durable construction, adjustable cutting heights, and dual grass management options, it established itself as a top-tier option for achieving a healthy and attractive lawn.
Top Page Image Contents