Tascam DA-45HR owner manual Table of Contents

Table of Contents

Table of Contents

1 - Introduction to the DA-45HR

1.1	Features	6
1.2	Unpacking and inspection	6
1.3	Installation of the tape deck	6
1.4	About DAT cassettes	6
1.4.1 Head cleaning		7
1.5	Making connections	7
1.5.1 Making analog connections		7
1.5.2 Making digital audio connections ...		7
1.5.3 Making word synchronization
	connections	7
1.5.4 Making control connections		8
1.5.5 Power connections		8
1.6	Block Diagram	8

1.6Front and Rear panels 2 - Parts of the tape deck

2.1 Power and display		10
[1] POWER switch		10
[2] Cassette tray and OPEN/CLOSE
button		10
[3] Display window		10
2.2 Recording mode and source
switches, etc		10
[4] CLOCK switch		10
[5] RECORD MODE switch		11
[6] Fs switch		11
[7] INPUT selector switch		11
[8] DIGITAL INPUT selector switch		11
[9] ANALOG INPUT selector switch		12
[10]	INPUT level controls	12
[11]	PHONES control and jack	12
2.3 Tape controls		12
[12]	SKIP keys	12
[13] REW and F FWD keys		12
[14] STOP key		12
[15]	PLAY key	13
[16] PAUSE key		13
[17] RECORD key		13
[18] REC MUTE key		13
[19] SHUTTLE wheel		14
[20]	DATA dial	14
2.4 Command keys		14
[21] COUNTER MODE		14
[22] CHAR		15
[23] MARGIN RESET		15
[24]	DISPLAY	15
[25] SKIP PLAY		15
[26] AUTO ID		15
[27] ENTER		15
[28] MENU		15
[29]	LOC 1	16
[30]	LOC 2	16
[31] SINGLE PLAY		16
[32]	SHIFT	16

2.5	Rear panel	16
[33] DIGITAL (AES/EBU) INPUT/OUTPUT. 16
[34] DIGITAL COAXIAL		16
[35] WORD IN and THRU (AUTO TERM) ...		16
[36] CONTROL I/O		16
[37] REMOTE IN		17
[38] ~ IN		17
[39] BALANCED ANALOG inputs		17
[40] UNBALANCED ANALOG inputs		17
[41] UNBALANCED ANALOG outputs		17
[42] BALANCED ANALOG outputs		17
3 - Menu functions
3.1	Drum time (head time)	18
3.2	Auto ID level	18
3.3	Auto ID time	18
3.4	Record mute time	18
3.5	Reference level	18
3.6	Digital output format	19
3.7	Digital out word length	19
3.8	Dither	19
3.9	Copy prohibit	19
3.10 End ID		19
3.11 HR time display		20
3.12 Repeat mode		20
3.13 Pre-roll time		20
3.14 End tally signal		20
3.15 Auto rewind		20
3.16 Fast forward mode		20
3.17 Parameter save		21
3.18 Initializing settings		21
3.19 Viewing points at which block errors
have occurred		21
4 - Advanced functions
4.1 REPEAT		22
4.2 CHECK		22
4.3	INS/+ and DEL/-	22
4.4 ID markers (START, SKIP, END, CHAR
and renumbering)		22
4.4.1 Selecting an ID mode		23
4.4.2 Manually writing a START or
	SKIP ID (i)	23
4.4.3 Writing a START or SKIP ID (ii)		23
4.4.4 Writing an END ID		24
4.4.5 Erasing a START or SKIP ID		24
4.4.6 Erasing an END ID		24
4.4.7 Erasing titles		24
4.4.8 Renumbering START IDs		24
4.5	The EDIT key	25
4.6	Location memories	25
4.6.1 Locating to location memories		25
4.6.2 Setting location memories		25
4.6.3 Editing location memories		25
4.7 Program mode		26
4.8	Character editing (titling)	26
4.8.1 Entering and editing titles		26

4 TASCAM DA-45HR