Fisher 244EH, 244ER B Approvals, Hazardous Locations Installations, Appendix, Safety Messages

Page 49

B Approvals

Appendix

B Approvals

SAFETY MESSAGES

Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page B-1 Hazardous Locations Installations . . . . . . . . . . . . . . . . . . page B-1 Locations Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . page B-2 Installation Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page B-4

Instructions and procedures in this section may require special precautions to ensure the safety of the personnel performing the operations. Information that raises potential safety issues is indicated by a warning symbol (). Please refer to the following safety messages before performing an operation preceded by this symbol.

Once a device labeled with multiple approval types is installed, it should not be reinstalled using any of the other labeled approval types. To ensure this, the approval label should be permanently marked to distinguish the used from the unused approval type(s).

HAZARDOUS LOCATIONS INSTALLATIONS

The Models 244E are available with circuitry that is suitable for intrinsically safe operation. The Model 244EH is available with optional explosion-proof enclosures and can be specified for non-incendive operation. Individual transmitters are clearly marked with a tag indicating the approvals they carry.

To maintain certified ratings for installed transmitters, they must be installed in accordance with all applicable installation codes and approval drawings. Verify that the operating atmosphere of the transmitter is consistent with the appropriate hazardous locations certification.

IMPORTANT

Once a device labeled with multiple approval types is installed, it should not be reinstalled using any of the other labeled approval types. To ensure this, the approval label should be permanently marked to distinguish the used from the unused approval type(s).

B-1

Image 49

Contents Models 244EH and 244ER PC-Programmable Temperature Transmitters 00809-0100-4737 English Rev. EAPage Models 244EH and 244ER PC-Programmable Temperature Transmitters Product Manual¢00809-0100-4737f¤ 00809-0100-4737 Rev EA 10/00Page Installation Table of ContentsMaintenance and TroubleshootingReference Data APPENDIX AAPPENDIX B ApprovalsSection SAFETY MESSAGES1 Introduction MANUAL OVERVIEW General CONSIDERATIONSMechanical ElectricalPage SAFETY MESSAGES Warnings 2 InstallationThe tools needed for installation are as follows TOOLS NEEDED FOR INSTALLATIONFigure 2-1. Transmitter Installation Flowchart Example MOUNTINGMounting a Model 244EH to a DIN Rail Special Mounting ConsiderationsTransmitter INSTALLATION PROCEDURESHead Mount Transmitter with DIN Plate Style Sensor Using Threaded Style Sensor Figure 2-6. Typical Model 244EH Transmitter Mounting Configurationand Assembly Head Mount Transmitter with Threaded SensorUsing Integral Mount Sensor and Assembly Figure 2-7. Typical Rail Mount Transmitter Mounting ConfigurationTo complete the assembly, follow the procedure described below 6. Run sensor lead wires from the sensor assembly to the transmitter644-0000A04B Rail Mount Transmitter with Threaded SensorMultichannel Installations Configuration SoftwareSystem Requirements Procedure for Windows 3.1 or Windows for Workgroups Choose the procedure that matches the operating system you are usingProcedure for Windows 95 or Windows NT Setting Up the Model 244EC Configuration Interface Model 244EC Configuration InterfaceScreen Conventions Figure 2-10. Complete Transmitter Configuration System FIELD WIRINGRTD or Ohm Inputs Sensor ConnectionsExamples of Approximate Lead Wire Resistance Effect Calculations Sensor Lead Wire Resistance Effect RTD InputGiven Total cable length = 150 mThermocouple or Millivolt Inputs Figure 2-13. Transmitter Power, Sensor, and Configuration Terminals FAILURE MODE Changing Switch Positions3 Operation POWER SUPPLY Surges/TransientsGrounding CONFIGURATIONFigure 3-1. Models 244EH and 244ER Configuration Software Main Configuring a Single TransmitterConfiguration Window Configuring Several Transmitters Identically INTERMITTENT SENSOR ALGORITHM Viewing the Process VariableFigure 3-2. Viewing the Process Variable with the 244EC Case 1 Open Sensor Case ExamplesCase 2 Temperature Change Greater than the Threshold Value2% of Output RangeCase 3 Temperature Change Within the Threshold Value 2 % of Range Intermittent Sensor Algorithm and Damping2.0 seconds, the transmitter outputs the reading that corresponds to Intermittent Sensor Detect Advanced Featurethe damping curve at that time , and continues to calculate and continues to approach the input curveaccordingto theequation aboveTransmitter Behavior with Intermittent Sensor Detect ON ImplementationTransmitter Behavior with Intermittent Sensor Detect OFF Page SAFETY INFORMATION 4 Maintenance and TroubleshootingTROUBLESHOOTING Model 244EH software version Error Message Troubleshooting ChartCause and Possible Solutions TABLE 4-1. Models 244EH and 244ERAppendix TRANSMITTER SPECIFICATION FunctionalA Reference Data Power SupplyUpdate Time PerformancePower Supply Effect CE Electromagnetic Compatibility Compliance TestingTABLE A-2. Model 244E Input Options and Accuracy AccuracySensor InputAmbient Temperature Effect Transmitters can be installed in locations where the ambientWeight PhysicalElectrical Connections Materials of ConstructionModel ORDERING INFORMATIONProduct Description HeadTABLE A-6. Transmitter Accessories TABLE A-5. Model 244EC Configuration Interface Ordering InformationTypical Model Number 244EC Part DescriptionCustom Configuration Standard ConfigurationUnless specified, transmitter will be shipped as follows TaggingEnclosure and Model 244EC Configuration Interface DIMENSIONAL DRAWINGS TransmitterConfiguration Interface Model 244ERPage B Approvals HAZARDOUS LOCATIONS INSTALLATIONSFactory Mutual FM Approvals LOCATIONS CERTIFICATIONSCanadian Standards Association CSA Approvals KEMA Approvals Standard Australia Quality Assurance Service SAASpecial Conditions for Safe Use Gostandart INSTALLATION DRAWINGSInstallation Drawing Rev. AB Figure B-1. Canadian Standards Association CSA Intrinsic SafetyFigure B-2. Canadian Standards Association CSA Explosion-Proof Installation Drawing Rev. AA00644-0009, Rev. AA Figure B-3. Factory Mutual FM Intrinsic Safety Installation Drawing00644-1049, Rev. AB Figure B-4. Factory Mutual FM Explosion-Proof Installation DrawingC Models 644 and 244E Temperature Transmitters Manual Supplement OLD TRANSMITTER Transmitter Design Sensor Wiring Diagrams Special MountingConsiderations Models 644H and 244EHConsiderations HART Communicator Model 644H only NEW TRANSMITTER2. Select 1 Off-line, 1 New Configuration, Rosemount, 644 Temp Use with an Existing DIN Plate Style SensorBASEFFA1 Intrinsically Safe Installation Entity Parameters SPECIFICATIONSFactory Mutual3 Entity ParametersIndex Wiring Page Product documentation available at