Cub Cadet 72-inch, 54-inch service manual Mower Cutting Blades, Parking the Mower

Page 15

Note: Do not hold the key in the “Start” position for more than 10 seconds or you may damage the starter. If the engine does not start in this time, wait about 30 seconds and try again.

i.Gasoline Engine: Once the engine starts, push the choke on halfway and as the engine warms, push the choke off all the way.

4.Operating the Mower: Operating a zero-turn- ing-radius mower is not like operating a trac- tor-type riding mower. The zero-turning-radius mower is much more maneuverable and much less fatiguing to operate. However, get- ting used to the fingertip control of the zero- turning-radius mower takes some practice. We strongly recommend that you locate a “test area” where you can operate the mower for about 30 minutes without being disturbed.

a.Get into the operator’s seat.

b.Start the engine.

c.Use the transport lever to raise the mowing deck to the transport position. Make sure the blade clutch switch is off.

d.After the engine has warmed, adjust the throttle to the fast position.

e.Release the parking brake.

f.Fold in the steering levers to the operating position.

WARNING:

When operating this mower forward, do not allow the steering levers to return to the neu- tral position on their own. Always maintain a firm grip on the steering levers, operate them smoothly and avoid any sudden movements of the levers when starting or stopping.

g.To go forward, move both steering levers slightly forward and the mower will slowly move forward. The farther you move the levers forward the faster the mower will go forward.

h.To back up, move both steering levers slightly backward and the mower will slowly move backward. The farther you move the levers backward the faster the mower will go backward.

i.To turn, pull the lever back on the side to which you want to turn. The farther back you pull the lever, the faster and more sharply you will turn. Initially, you will have to be careful to avoid turning to fast and too far.

j.After you have mastered operating the mower, use the transport lever to lower the mowing deck to the cutting position and pull on the electric blade clutch switch to start the blades rotating.

k.Practice mowing in straight passes. When you feel confident, slowly practice mowing around obstacles such as trees.

5.Parking the Mower:

a.Push off the electric blade clutch switch.

b.Use the Deck Lift Handle to raise the mow- ing deck to the transport position.

c.Drive the mower to the cleanup or storage area.

d.Move the throttle to slow.

e.Place the steering levers in the neutral position.

f.Set the parking brake.

g.Turn off the ignition switch and take the key from the switch.

h.Close the fuel shutoff valves.

E.Mower Cutting Blades

The blades normally “factory installed” on a mower afford the best grass cutting performance on the majority of grasses and mowing conditions; however, there will be occasions whereby the grass type, stage of grass growth, soil conditions, and weather conditions will require different cutting blade types. Since the mower decks are designed so that over-lap of the cutting blades generally exceed 1.5”, there is no need for orientation of one cutting blade to an adjacent blade (I.E., the blades do not need to be “timed” nor synchronized).

Hi-lift- These are generally the best cutting blades for most grasses and mowing conditions. These blades will provide extra “lift” for the thinner leaf grasses, will handle lush grasses, and will provide maximum grass and debris discharge. These blades are generally required for material collection sys- tems. More horsepower is required for these blades when compared to others, and they generally pro- duce the highest noise levels.

Medium-lift- These blades require less horsepower than the hi-lift, and they generally work well in wider leaf grasses and some mulch applications.

Low-lift- These blades require less horsepower than hi-lift and medium-lift blades, and they generally work best with wide leaf grasses, sparse grass growth, and sandy soil conditions. They generally produce the lowest noise levels. Bahia blades are configured without offset, and with a maximum amount of sharp- ened cutting edge.

Mulch- These blades are generally designed for use in cutting decks equipped with mulch baffles. The shape of the blade generally produces higher turbu- lence in order that the grass can be repeatedly cut and re-cut into smaller pieces. These blades gener- ally require more horsepower than other blades. Mulch blades work best when the grasses are cut at the highest levels, minimal lengths of grasses are removed, and grass conditions are generally dry.

15

Image 15
Contents Hydrostatic Zero-Turn Commercial Riding Mower Table of Contents Forward General Safety Operations Safety PrecautionsGeneral When Mowing Related to FuelRelated to Batteries Page Shield Missing do not Operate Safety Decals and LabelsSpecifications When Mowing Safety Awareness when MowingOperating Instructions To Mow Grass and Produce a Striped Pat- tern Figure Fuel Shutoff Valve Check the fluid levels and tires Initial AdjustmentsInitial Operation Zero Turn Break-In And Operating ProceduresLubricate all fittings listed in the mainte- nance section OrientationStart the Engine Parking the Mower Mower Cutting BladesChanging a Blade Maintenance ServiceMower Deck Removing the Mower DeckChanging the Spindle Assembly Hydraulic OilChanging the Blade Drive Belts Draining Hydraulic Oil Stop the engine and remove the key from the ignition switchElectrical Circuit Adding Hydraulic Oil use Rimula SAE15W40Jump Starting Battery RemovalInstalling the Battery Specific Gravity Freezing Temp FInflation Pressure TiresBrakes Hydraulic Oil Tank and Filter ScrewStorage To Put the Mower Back in ServiceMaintenance Schedule If Mower is so equipped OIL ChartEnginge RPM Check and Adjustment High Speed Tracking AdjustmentDeck Corner Ball Wheel Roller Settings Deck Center Anti-Scalp Roller SettingsLap Bar Adjustment Deck leveling Procedure Wiring Diagram Maintenance Record Page MANUFACTURER’S Limited Warranty Turf Equipment

48-inch, 54-inch, 60-inch, 72-inch, 54-inch, 72-inch specifications

Cub Cadet has long been a trusted name in outdoor power equipment, particularly when it comes to riding lawn mowers and lawn tractors. Among its impressive lineup, the 48-inch, 54-inch, 60-inch, and 72-inch cutting decks stand out for their power, performance, and innovative features tailored to meet the needs of both homeowners and professional landscapers.

Starting with the 48-inch cutting deck, this model is perfect for smaller to mid-sized lawns. It boasts a tight turning radius and exceptional maneuverability, making it easy to access narrow spaces and navigate around obstacles. Equipped with a powerful engine, the 48-inch deck provides efficient cutting, ensuring a professional finish every time.

The 54-inch cutting deck offers a slightly larger option, ideal for larger residential properties or commercial applications. This model incorporates advanced features such as the Cub Cadet’s AeroForce technology, which enhances airflow to create a superior cut and reduces clumping yard debris. The durable construction of the 54-inch deck ensures longevity, paired with easy-to-adjust cutting height settings for versatile lawn care.

For those requiring even more power and coverage, the 60-inch cutting deck delivers outstanding performance on expansive lawns. It features a heavy-duty design that enhances durability and precision in cutting. With exceptional stability, this mower easily handles uneven terrain, providing a consistent blade height thanks to its advanced deck leveling system.

The 72-inch cutting deck is designed for professional landscapers and those with substantial property needs. This deck covers wide areas rapidly, reducing mowing time. It is engineered with a robust build, featuring reinforced blades that enhance cutting power. The 72-inch model also incorporates vibration-dampening technology, ensuring operator comfort during extended use.

Across all Cub Cadet models, key characteristics include ease of use with an intuitive dashboard, hydrostatic transmission for smooth maneuvering, and powerful engines that cater to the rigors of lawn care. The mowers also boast innovative safety features, including automatic blade brake systems and operator presence controls that require the operator to remain engaged while mowing.

With exceptional cutting technology, robust engineering, and varied sizes to meet different lawn demands, the Cub Cadet 48-inch, 54-inch, 60-inch, and 72-inch cutting decks stand as top choices for anyone seeking reliability and performance in lawn care. Whether for residential use or professional landscaping, these mowers deliver quality results with each pass.