Cub Cadet 48-inch, 54-inch, 60-inch, 72-inch Storage, To Put the Mower Back in Service

Page 23

opened out to the neutral position. If the Mower begins to creep, adjust the Steering Levers.

If the mower creeps, first determine whether it creeps to the right or left side and which direc- tion the mower moves — to the front or the rear. To make the adjustment, place the steer- ing levers in the opened-out neutral position and set the parking brake, shutoff the engine, take the key from the ignition switch and pivot the seat forward. If the mower creeps to the right, you will adjust the linkage on the left side of the mower and vice-versa. Remove the cap screw and lock washer that secure the linkage control arm rod end bearing to the control lever pivot. Loosen the jam nut which prevents the rod end bearing from turning. If the mower creeps forward, thread the rod end bearing one-half turn clockwise into the link- age control arm. If the mower creeps back- ward, thread the rod end bearing one half turn counterclockwise out of the linkage control arm. Then tighten the jam nut and reconnect the rod end bearing to the control lever pivot by replacing the cap screw and lock washer.

After adjusting the steering linkage, swing the seat back to its normal position and place the steering lever on the side you adjusted up to the operating position. If you feel a slight push forward or a slight pull backward from the neutral position you must adjust the lever return assembly. To do this, swing the steering lever back out to the neutral position, pivot the seat forward and loosen the jam nut on the lever return rod where it is threaded into the hex-shaped end of the lever return bolt. If the steering lever was pushed forward, turn the hex-shaped lever return bolt clockwise one- half turn off of the lever return rod. If the steer- ing lever was pulled back, turn the hex shaped lever return bolt counterclockwise one-half turn onto the lever return rod. Then tighten the jam nut, pivot the seat back into the operating position and start the mower to check that your adjustments were made correctly.

G.Storage

1.General: If your mower will not be in service for a few months, it should be stored in a dry location that is not subject to drastic changes in temperature. Before storing, the following maintenance procedures should be per- formed.

Note: For E.F.I. Tanks, disconnect the neg- ative lead of the battery for storage of 4 weeks or more.

a.Clean the mower. The entire tractor and cutting deck should be washed and cleaned.

b.Sharpen the blades so that the mower will be ready to use when needed.

c.Protect the metal surfaces. Repair scratches with the appropriate touch-up spray paint. Brush a rust preventive oil on any unpainted surfaces including the pul- leys and blades. (Be careful not to get any oil on the drive belts.)

d.Lubricate the mower.

e.Drain the engine oil. The engine should be warm so that all the oil drains. Replace the engine oil filter and refill the crankcase with fresh oil.

f.Gasoline Engine: Drain all the fuel. Close the fuel tank shutoff valve. Disconnect the fuel line from the carbuetor and put the end into an approved fuel container. Open the fuel tank shutoff valve and drain the fuel tank and line into the approved container. Replace the fuel line on the carburetor. Start the engine and allow it to run out of fuel. This will prevent gum and varnish deposits from forming. Replace the fuel fil- ter.

g.Gasoline Engine Only: Remove the spark plugs and pour approximately one ounce of oil into each cylinder. Crank the engine one or two turns to spread the oil evenly on the cylinder walls. Replace the spark plugs.

h.Disconnect, clean and make sure the bat- tery is fully charged.

i.Inspect the hydraulic hoses, lines and fit- tings. Replace as necessary.

j.Jack the mower up and store it on blocks to take the weight off of the tires.

2.To Put the Mower Back in Service:

a.Check the battery. Charge if necessary.

b.Gasoline Engine Only: Remove the spark plugs and wipe them off. Using the starter, crank the engine to pump the excess oil out of the spark plug holes. Replace the spark plugs and the ignition leads. Refill the fuel tank with fresh gasoline.

c.Check the level of the oil in the crankcase and the hydraulic tank.

d.Lower the mower off the block and check the tire pressure.

e.Push the mower outdoors and start the engine. Let the engine idle until it has warmed up completely (4 to 5 minutes).

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Hydrostatic Zero-Turn Commercial Riding Mower Table of Contents Forward General General Safety OperationsSafety Precautions Related to Batteries When MowingRelated to Fuel Page Shield Missing do not Operate Safety Decals and LabelsSpecifications Operating Instructions When MowingSafety Awareness when Mowing To Mow Grass and Produce a Striped Pat- tern Figure Fuel Shutoff Valve Check the fluid levels and tires Initial AdjustmentsInitial Operation Zero Turn Break-In And Operating ProceduresLubricate all fittings listed in the mainte- nance section OrientationStart the Engine Parking the Mower Mower Cutting BladesChanging a Blade Maintenance ServiceMower Deck Removing the Mower DeckChanging the Blade Drive Belts Changing the Spindle AssemblyHydraulic Oil Draining Hydraulic Oil Stop the engine and remove the key from the ignition switchElectrical Circuit Adding Hydraulic Oil use Rimula SAE15W40Jump Starting Battery RemovalInstalling the Battery Specific Gravity Freezing Temp FInflation Pressure TiresBrakes Hydraulic Oil Tank and Filter ScrewStorage To Put the Mower Back in ServiceMaintenance Schedule If Mower is so equipped OIL ChartEnginge RPM Check and Adjustment High Speed Tracking AdjustmentLap Bar Adjustment Deck Corner Ball Wheel Roller SettingsDeck Center Anti-Scalp Roller Settings Deck leveling Procedure Wiring Diagram Maintenance Record Page MANUFACTURER’S Limited Warranty Turf Equipment

48-inch, 54-inch, 60-inch, 72-inch, 54-inch, 72-inch specifications

Cub Cadet has long been a trusted name in outdoor power equipment, particularly when it comes to riding lawn mowers and lawn tractors. Among its impressive lineup, the 48-inch, 54-inch, 60-inch, and 72-inch cutting decks stand out for their power, performance, and innovative features tailored to meet the needs of both homeowners and professional landscapers.

Starting with the 48-inch cutting deck, this model is perfect for smaller to mid-sized lawns. It boasts a tight turning radius and exceptional maneuverability, making it easy to access narrow spaces and navigate around obstacles. Equipped with a powerful engine, the 48-inch deck provides efficient cutting, ensuring a professional finish every time.

The 54-inch cutting deck offers a slightly larger option, ideal for larger residential properties or commercial applications. This model incorporates advanced features such as the Cub Cadet’s AeroForce technology, which enhances airflow to create a superior cut and reduces clumping yard debris. The durable construction of the 54-inch deck ensures longevity, paired with easy-to-adjust cutting height settings for versatile lawn care.

For those requiring even more power and coverage, the 60-inch cutting deck delivers outstanding performance on expansive lawns. It features a heavy-duty design that enhances durability and precision in cutting. With exceptional stability, this mower easily handles uneven terrain, providing a consistent blade height thanks to its advanced deck leveling system.

The 72-inch cutting deck is designed for professional landscapers and those with substantial property needs. This deck covers wide areas rapidly, reducing mowing time. It is engineered with a robust build, featuring reinforced blades that enhance cutting power. The 72-inch model also incorporates vibration-dampening technology, ensuring operator comfort during extended use.

Across all Cub Cadet models, key characteristics include ease of use with an intuitive dashboard, hydrostatic transmission for smooth maneuvering, and powerful engines that cater to the rigors of lawn care. The mowers also boast innovative safety features, including automatic blade brake systems and operator presence controls that require the operator to remain engaged while mowing.

With exceptional cutting technology, robust engineering, and varied sizes to meet different lawn demands, the Cub Cadet 48-inch, 54-inch, 60-inch, and 72-inch cutting decks stand as top choices for anyone seeking reliability and performance in lawn care. Whether for residential use or professional landscaping, these mowers deliver quality results with each pass.
Top Page Image Contents