Cub Cadet LT1022, LT1018 manual Fuse, Cutting Deck Removal, Changing the Deck Belts

Page 21

Fuse

A fuse is installed in your tractor’s wiring harness to protect the tractor’s electrical system from damage caused by excessive amperage.

If the electrical system does not function, or your tractor’s engine will not crank, first check to be certain that the fuse has not blown.

It can be found under the hood mounted behind the top of the dash panel on the support bar. Pull the fuse out and inspect it to determine if it is good or blown.

IMPORTANT: Always use a fuse with the same amperage capacity for replacement.

WARNING: Before servicing, repairing, or inspecting, always disengage PTO, set parking brake, stop engine and remove key to prevent unintended starting.

Cutting Deck Removal

To remove the cutting deck, proceed as follows:

•Place the PTO/Blade Engage knob in the disengaged (OFF) position and engage the parking brake.

•Lower the deck by moving the deck lift lever into the bottom notch on the right fender.

•Remove the PTO belt from around the tractor’s electric PTO clutch. Refer to Figure 18 or Figure 19.

•Looking at the cutting deck from the left side of the tractor, locate the deck support pin on the rear left side of the deck.

•Rotate the pin slightly toward the rear of the tractor and release the pin into the hole provided.

•Pull the deck support pin outward to release the deck from the deck lift arm. See Figure 17.

Support Pin

Figure 17

•Repeat the above steps on the tractor’s right side.

•Move the deck lift lever into the top notch on the right fender to raise the deck lift arms up and out of the way.

•Gently slide the cutting deck toward the front of the tractor allowing the hooks on the deck to release themselves from the deck stabilizer rod.

•Gently slide the cutting deck (from the right side) out from underneath the tractor.

Changing the Deck Belt(s)

WARNING: Be sure to shut the engine off, remove ignition key, disconnect the spark plug wire(s) and ground against the engine to prevent unintended starting before removing the belt(s).

All belts on your tractor are subject to wear and should be replaced if any signs of wear are present.

IMPORTANT: The V-belts found on your tractor are specially designed to engage and disengage safely. A substitute (non-OEM) V-belt can be dangerous by not disengaging completely. For a proper working machine, use factory approved belts.

To change or replace the deck belts on your tractor, proceed as follows:

•Lower the deck by moving the deck lift lever into the bottom notch on the right fender.

•Remove the belt guards by removing the self- tapping screws that fasten them to the deck. See Figure 18 or Figure 19.

•Grasp the rearmost portion of the PTO idler bracket and pivot it toward the discharge chute to relieve tension on the PTO belt.

•Remove the PTO belt from the electric PTO clutch and the PTO idler pulley(s).

•Grasp the deck idler pulley and pivot it toward the left side of the deck to relieve tension on the deck belt.

•Remove the deck belt from around all pulleys, including the deck idler pulley.

•Route the new belts as shown in Figure 18 or Figure 19.

•Remount the belt guards removed earlier.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Operator’s Manual Table of Contents General Operation Important Safe Operation PracticesDo not Slope OperationChildren TowingSafe Handling of Gasoline ServiceDange Slope Gauge Shipping Brace Removal Gas and Oil Fill-upKnow Your Lawn Tractor Throttle Control Lever Ignition SwitchChoke Control Brake PedalHour Meter System Indicator LightsCup Holder Electric PTO Blade Engage KnobSafety Interlock Switches Seat Adjustment LeverSetting the Gauge Wheels Operating Your Lawn TractorStopping the Engine Starting the EngineEngaging the Parking Brake Driving The TractorUsing the Deck Lift Lever Setting The Cruise ControlDriving On Slopes Operating The HeadlightsEngaging the PTO Moving The Tractor ManuallyMowing OFFLeveling the Deck Making AdjustmentsParking Brake Adjustment Steering AdjustmentSeat Adjustment Maintaining Your Lawn Tractor Cleaning the Engine And DeckEngine LubricationTires ServiceHead Lamps Cutting BladesJump Starting BatteryFuse Cutting Deck RemovalChanging the Deck Belts Models 1022 Front of Tractor Hydrostatic Transmission OFF-SEASON StorageAttachments & Accessories TroubleshootingHydrostatic Transmission SpecificationsCommercial USE CUB Cadet LLC MANUFACTURER’S ONE Year Limited WarrantyResidential USE CUB Cadet LLC MANUFACTURER’S Limited Warranty

LT1018, LT1022 specifications

The Cub Cadet LT1022 and LT1018 are two standout models in the world of riding lawn mowers, designed for homeowners who want efficiency, comfort, and the power to tackle their mowing tasks with ease. Both models exemplify the fusion of innovative technologies and user-friendly features, making them an ideal choice for maintaining lawns of various sizes.

Starting with the Cub Cadet LT1022, this riding mower is equipped with a powerful 22 HP Kohler engine, ensuring ample power to handle tough mowing conditions. The 42-inch cutting deck provides a wide mowing path, reducing the number of passes needed to cover larger lawns, which ultimately saves time. The LT1022 also features a sophisticated hydrostatic transmission that allows for smooth and effortless speed adjustments, giving the operator complete control over mowing speed without the need to shift gears.

Another notable feature of the LT1022 is its enhanced cutting technology. The mower is designed with a mulching kit, side discharge, and bagging options, providing versatility in how grass clippings are managed. The adjustable cutting height, ranging from 1.5 to 4 inches, ensures precise grass cutting tailored to the user’s lawn care preferences.

On the other hand, the Cub Cadet LT1018 caters to those who may require a slightly smaller package without sacrificing performance. With an 18 HP Kohler engine, it still packs enough power for medium-sized lawns. The 42-inch cutting deck allows for efficient mowing, similar to the LT1022, making it suitable for navigating tight spaces while effectively managing larger areas as well.

Both models feature a comfortable high-back seat, ensuring that users can mow for extended periods without discomfort. The easy-to-use dashboard provides clear visibility of important information, including fuel level and blade engagement status, enhancing the overall user experience.

In terms of ease of maintenance, the LT1022 and LT1018 come with accessible service points, making it simple for owners to perform routine checks and maintenance tasks. The durable construction of both mowers ensures that they can withstand the rigors of regular use, providing a reliable mowing solution for years to come.

In summary, the Cub Cadet LT1022 and LT1018 offer a blend of power, advanced cutting technologies, and user-friendly features that make them excellent choices for any homeowner looking to maintain their lawn efficiently and effectively.
Top Page Image Contents