Service, Safe Handling of Gasoline | Cub Cadet LT1022, LT1018

SERVICE

SAFE HANDLING OF GASOLINE:

1.To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Serious personal injury can occur when gasoline is spilled on yourself or your clothes which can ignite. Wash your skin and change clothes immediately.

a.Use only an approved gasoline container.

b.Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground away from your vehicle before filling.

c.When practical, remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle.

d.Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device.

e.Extinguish all cigarettes, cigars, pipes and other sources of ignition.

f.Never fuel machine indoors.

g.Never remove gas cap or add fuel while the engine is hot or running. Allow engine to cool at least two minutes before refueling.

h.Never over fill fuel tank. Fill tank to no more than three inches below the top of the filler neck to allow space for fuel expansion.

i.Replace gasoline cap and tighten securely.

j.If gasoline is spilled, wipe it off the engine and equipment. Move unit to another area. Wait 5 minutes before starting the engine.

k.To reduce fire hazards, keep machine free of grass, leaves, or other debris build-up. Clean up oil or fuel spillage and remove any fuel soaked debris.

l.Never store the machine or fuel container inside where there is an open flame, spark or pilot light as on a water heater, space heater, furnace, clothes dryer or other gas appliances.

m.Allow a machine to cool at least five minutes before storing.

GENERAL SERVICE:

1.Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless, and deadly gas.

2.Before cleaning, repairing, or inspecting, make certain the blade(s) and all moving parts have stopped. Disconnect the spark plug wire and ground against the engine to prevent unintended starting.

3.Periodically check to make sure the blades come to complete stop within approximately (5) five seconds after operating the blade disengagement control. If the blades do not stop within the this time frame, your unit should be serviced professionally by an authorized Cub Cadet dealer.

4.Check brake operation frequently as it is subjected to wear during normal operation. Adjust and service as required.

5.Check the blade(s) and engine mounting bolts at frequent intervals for proper tightness. Also, visually inspect blade(s) for damage (e.g., excessive wear, bent, cracked).

Replace the blade(s) with the original equipment manufacturer’s (O.E.M.) blade(s) only, listed in this manual. “Use of parts which do not meet the original equipment specifications may lead to improper performance and compromise safety!”

6.Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them.

7.Keep all nuts, bolts, and screws tight to be sure the equipment is in safe working condition.

8.Never tamper with the safety interlock system or other safety devices. Check their proper operation regularly.

9.After striking a foreign object, stop the engine, disconnect the spark plug wire(s) and ground against the engine. Thoroughly inspect the machine for any damage. Repair the damage before starting and operating.

10.Never attempt to make adjustments or repairs to the machine while the engine is running.

11.Do not change the engine governor settings or over- speed the engine. The governor controls the maximum safe operating speed of the engine.

12.Maintain or replace safety and instruction labels, as necessary.

13.Observe proper disposal laws and regulations for gas, oil, etc. to protect the environment.

14.Grass catcher components and the discharge cover are subject to wear and damage which could expose moving parts or allow objects to be thrown. For safety protection, frequently check components and replace immediately with original equipment manufacturer’s (O.E.M.) parts only, listed in this manual. “Use of parts which do not meet the original equipment specifications may lead to improper performance and compromise safety!”

WARNING: YOUR RESPONSIBILITY Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine.

LT1018, LT1022 specifications

The Cub Cadet LT1022 and LT1018 are two standout models in the world of riding lawn mowers, designed for homeowners who want efficiency, comfort, and the power to tackle their mowing tasks with ease. Both models exemplify the fusion of innovative technologies and user-friendly features, making them an ideal choice for maintaining lawns of various sizes.

Starting with the Cub Cadet LT1022, this riding mower is equipped with a powerful 22 HP Kohler engine, ensuring ample power to handle tough mowing conditions. The 42-inch cutting deck provides a wide mowing path, reducing the number of passes needed to cover larger lawns, which ultimately saves time. The LT1022 also features a sophisticated hydrostatic transmission that allows for smooth and effortless speed adjustments, giving the operator complete control over mowing speed without the need to shift gears.

Another notable feature of the LT1022 is its enhanced cutting technology. The mower is designed with a mulching kit, side discharge, and bagging options, providing versatility in how grass clippings are managed. The adjustable cutting height, ranging from 1.5 to 4 inches, ensures precise grass cutting tailored to the user’s lawn care preferences.

On the other hand, the Cub Cadet LT1018 caters to those who may require a slightly smaller package without sacrificing performance. With an 18 HP Kohler engine, it still packs enough power for medium-sized lawns. The 42-inch cutting deck allows for efficient mowing, similar to the LT1022, making it suitable for navigating tight spaces while effectively managing larger areas as well.

Both models feature a comfortable high-back seat, ensuring that users can mow for extended periods without discomfort. The easy-to-use dashboard provides clear visibility of important information, including fuel level and blade engagement status, enhancing the overall user experience.

In terms of ease of maintenance, the LT1022 and LT1018 come with accessible service points, making it simple for owners to perform routine checks and maintenance tasks. The durable construction of both mowers ensures that they can withstand the rigors of regular use, providing a reliable mowing solution for years to come.

In summary, the Cub Cadet LT1022 and LT1018 offer a blend of power, advanced cutting technologies, and user-friendly features that make them excellent choices for any homeowner looking to maintain their lawn efficiently and effectively.