Cub Cadet 18HP service manual Start the Engine

Page 13

ning. Sit down and the engine should run. Turn off the PTO by pushing the control switch down.

h.To drive in the FORWARD direction:

1.Set the engine speed to 2000 to 2500 rpm (refer to tachometer on right control panel). This must be increased to full speed (3525-3675 rpm) after becoming familiar with the machine.

2.Release the park brake to the down posi- tion.

3.Move both lap bars out of the neutral/ start position to the neutral position (toward center of machine). Slowly, move both lap bars toward the front of the machine until the machine begins to move forward — release the lap bars and the machine should stop. The more that the lap bars are moved toward the front of the machine, the faster the machine will move in the forward direc- tion. Release the lap bars and the machine should stop traveling forward. (This is a safety check, the normal pro- cedure is for the operator to slowly bring the lap bars to the neutral position).

4.Do not advance the lap bars rapidly as this could cause turf defacement, loss of traction, and/or instability.

5.To turn, advance one lap bar ahead of the other and the machine will turn toward the opposite from the side that was advanced — I.E. to turn clockwise (to the Right), move the LEFT lap bar for- ward more than the right side, and to turn counter-clockwise (to the LEFT), move the RIGHT lap bar forward more than the left side. NOTE: If one lap bar is in the neutral position and the other is advanced, the turn side tire will not rotate and a “pivot turn” will be executed

— turf defacement could occur (if on grass) as well as potential damages to the traction surface and the tire. If the lap bar on the turn side is not brought all the way to neutral, then the turn side tire will continue to rotate and a “U-turn” will be executed with a low potential for turf defacement as well as traction surface and tire damage.

i.To drive in the REVERSE direction:

1.Make sure no bystanders, animals, or objects are behind the machine. Look behind the machine, and use extreme care.

2.Slowly, move both lap bars toward the rear of the machine until the machine

begins to move rearward. Release the lap bars and the machine should stop. The more the lap bars are moved toward the rear of the machine, the faster the machine will move in the reverse direc- tion. Release the lap bars and the machine should stop traveling in reverse (this is a safety check, the normal proce- dure is for the operator to slowly bring the lap bars to the neutral position).

3.Do not retard the lap bars rapidly as this could cause turf defacement and/or loss of traction.

4.To turn, retard one lap bar ahead of the other and the machine will turn toward the same side that was retarded — I.E., to turn counter-clockwise (to the LEFT), move the LEFT lap bar rearward more than the right side, and to turn clockwise (to the RIGHT), move the RIGHT lap bar rearward more than the left side. NOTE: If one lap bar is in the neutral position and the other is retarded, the turn side tire will not rotate and a “pivot turn” will be executed. Turf defacement could occur (if on grass) as well as potential damages to the traction surface and the tire. If the lap bar on the turn side is not brought all the way to neutral, then the turn side tire will continue to rotate and a “U-turn” will be executed with a low potential for turf defacement as well as traction surface and tire damage.

j.To perform a “zero turn”:

1.Please note, a zero turn maneuver can not be executed while the machine is moving in the Forward or, Reverse direc- tions, the machine must come to a stop first.

2.To turn clockwise, slowly move the LEFT lap bar forward while simultaneously moving the RIGHT lap bar rearward. Release both lap bars and the machine should stop turning.

3.To turn counter-clockwise, slowly move the RIGHT lap bar forward while simulta- neously moving the LEFT lap bar rear- ward. Release both lap bars and the machine should stop turning (this is a safety check, the normal procedure is for the operator to slowly bring the lap bars to the neutral position).

3.Start the Engine:

a.Open the fuel shutoff valve.

b.Sit on the Seat. Set the parking brake “On” to the up position.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Hydrostatic Zero-Turn Riding Mower Table of Contents Forward Safety Precautions General Safety OperationsGeneral Related to Fuel When MowingShield Missing do not Operate Safety Decals and LabelsSpecifications Safety Awareness when Mowing When MowingOperating Instructions To Mow Grass and Produce a Striped Pat- tern Figure Fuel Shutoff Valve Check the fluid levels and tires Initial AdjustmentsLubricate all fittings listed in the mainte- nance section Zero Turn Break-In And Operating ProceduresOrientation Initial OperationStart the Engine Mower Deck Maintenance ServiceParking the Mower Removing the Mower DeckChanging the Blade Drive Belts Changing a BladeStop the engine and remove the key from the ignition switch Changing the Spindle AssemblyHydraulic Oil Adding Hydraulic Oil use SAE20WInstalling the Battery Battery RemovalElectrical Circuit Specific Gravity Freezing Temp FPage Brakes TiresInflation Pressure Hydraulic Oil Tank and Filter Hydraulic SystemStorage Maintenance Schedule If Mower is so equipped OIL ChartEnginge RPM Check and Adjustment High Speed Tracking AdjustmentDeck Center Anti-Scalp Roller Settings Deck Corner Ball Wheel Roller SettingsLap Bar Adjustment Deck leveling Procedure Wiring Diagram Equipment TWO-YEAR Limited Warranty

18HP specifications

The Cub Cadet 18HP is a robust and versatile garden tractor designed to meet the demanding needs of homeowners and landscaping professionals alike. This machine packs a powerful engine, advanced features, and user-friendly technologies that make lawn care and garden maintenance an efficient and enjoyable experience.

At the heart of the Cub Cadet 18HP is a high-performance 18 horsepower Kohler engine. This engine is engineered for reliability and effectiveness in a variety of mowing and hauling tasks. With a smooth and powerful operation, it efficiently tackles tough grass and uneven terrain, ensuring a pristine cut every time. The engine's two-cylinder design contributes to reduced vibrations and improved fuel efficiency, making it not only powerful but also economical to operate.

One of the standout features of the Cub Cadet 18HP is its innovative Cub Cadet signature cutting deck. The tractor is equipped with a 42-inch or 50-inch cutting deck, meticulously designed for superior grass cutting and discharge. This cutting system features twin blades that deliver an exceptional cut quality while reducing clumping and providing optimal air flow. The adjustable cutting height allows users to customize the grass length to their preference, ensuring a well-manicured lawn.

Incorporating advancements in technology, the Cub Cadet 18HP is equipped with a hydrostatic transmission. This feature provides smooth and effortless speed control, allowing homeowners to easily navigate around their properties without the need for constant gear shifting. Whether tackling inclines or navigating tight spaces, the hydrostatic transmission ensures maximum control and maneuverability.

Comfort is also a priority with the Cub Cadet 18HP. The tractor boasts a spacious, ergonomically designed seat that offers excellent support during extended use. Additionally, the easy-to-reach controls and cup holder enhance the overall user experience. Built-in headlights provide visibility for early morning or late evening mowing sessions, ensuring that users can work with ease at any time of day.

For those looking to expand the functionality of their tractor, the Cub Cadet 18HP supports a variety of attachments. From baggers to snow blades and tillers, this versatility allows users to tackle different tasks throughout the seasons, making it a true all-in-one gardening solution.

In summary, the Cub Cadet 18HP stands out in its category for its powerful engine, innovative cutting deck, hydrostatic transmission, and user-centric design. This garden tractor promises durability and efficiency, making it an indispensable tool for anyone serious about lawn care. Whether you are a weekend warrior or a landscaping professional, the Cub Cadet 18HP is built to handle the job with ease and reliability.
Top Page Image Contents