Cub Cadet 18HP service manual Changing the Spindle Assembly, Adding Hydraulic Oil use SAE20W

Page 16

Cover

Plate

Spindle

Figure. 7

blade drive belt from the pulley and slide the belt away from the pulley.

d.Remove tension of the PTO belt by moving the belt tensioning rod. Loosen the belt retaining bolt.

e.Pull the tensioner pulley away from the belt and remove the PTO belt then remove the blade drive belt.

f.Reverse the process to install the belt.

Note: When replacing belts do not over- tighten. Adjust the idler pulley so that a ten- pound pull with a spring scale between two pulleys deflects the belt about 1/2".

4.Changing the Spindle Assembly

a.Jack up the front of the mowing deck about one foot and block it in that position.

b.Make sure the blade clutch is disengaged.

c.Remove the deck cover.

d.Remove the drive belts. (See 3. Changing Blade Drive Belts.)

e.Remove the cutter blade. (See 2. Chang- ing a Blade.)

f.Using a wrench or socket rachet remove four hex nuts, and the four hex head cap screws. Remove the spindle assembly.

B.Hydraulic Oil

WARNING:

Never overfill the hydraulic units. Damage can occur if the oil level is not within the proper operating range.

Note: When adding hydraulic oil, do so in

small quantities and recheck the oil level before adding more. It is important that you do not overfill the reservoir.

Figure. 8

Hydraulic Tank

1.Adding Hydraulic Oil (use SAE20W 50)

a.Place the Mower on a level surface and engage the parking brake.

b.Stop the engine and remove the key from the ignition switch.

c.Clean the area around the Hydraulic Oil fill neck.

d.Remove the hydraulic fill cap and check the level. The correct level is up to the low- est hole of the oil tank fill neck.

e.Pour hydraulic oil into the reservoir up to the lowest hole in the oil tank fill neck, if necessary.

2.Draining Hydraulic Oil

Used hydraulic oil must be disposed of properly. Do not pour it down a drain or sewer, or dump it on open land, this creates an environmental hazard. Please be aware of the environment when disposing of used oil.

a.Place the Mower on a level surface and engage the parking brake.

b.Stop the engine and remove the key from the ignition switch.

c.Remove the mower deck. See Mower Deck on page 13.

d.Raise the seat forward to expose the hydraulic oil fill point.

e.Clean the area around the hydraulic fill oil cap.

f.Remove hydraulic fill oil cap.

g.Place a suitable container (at least 2 gal- lon) under the hydraulic reservoir and filter.

h.Remove the hydraulic filter to allow hydrau- lic oil to drain. Remove the drain plug from the bottom of the hydraulic oil tank to drain. Replace the plug.

i.Place a small pan under the skid plate. Remove fill oil cap from hydraulic reservoir for faster drainage. Remove nut caps and

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Hydrostatic Zero-Turn Riding Mower Table of Contents Forward Safety Precautions General Safety OperationsGeneral When Mowing Related to FuelSafety Decals and Labels Shield Missing do not OperateSpecifications Safety Awareness when Mowing When MowingOperating Instructions To Mow Grass and Produce a Striped Pat- tern Figure Fuel Shutoff Valve Initial Adjustments Check the fluid levels and tiresZero Turn Break-In And Operating Procedures Lubricate all fittings listed in the mainte- nance sectionOrientation Initial OperationStart the Engine Maintenance Service Mower DeckParking the Mower Removing the Mower DeckChanging a Blade Changing the Blade Drive BeltsChanging the Spindle Assembly Stop the engine and remove the key from the ignition switchHydraulic Oil Adding Hydraulic Oil use SAE20WBattery Removal Installing the BatteryElectrical Circuit Specific Gravity Freezing Temp FPage Brakes TiresInflation Pressure Hydraulic System Hydraulic Oil Tank and FilterStorage Maintenance Schedule OIL Chart If Mower is so equippedHigh Speed Tracking Adjustment Enginge RPM Check and AdjustmentDeck Center Anti-Scalp Roller Settings Deck Corner Ball Wheel Roller SettingsLap Bar Adjustment Deck leveling Procedure Wiring Diagram Equipment TWO-YEAR Limited Warranty

18HP specifications

The Cub Cadet 18HP is a robust and versatile garden tractor designed to meet the demanding needs of homeowners and landscaping professionals alike. This machine packs a powerful engine, advanced features, and user-friendly technologies that make lawn care and garden maintenance an efficient and enjoyable experience.

At the heart of the Cub Cadet 18HP is a high-performance 18 horsepower Kohler engine. This engine is engineered for reliability and effectiveness in a variety of mowing and hauling tasks. With a smooth and powerful operation, it efficiently tackles tough grass and uneven terrain, ensuring a pristine cut every time. The engine's two-cylinder design contributes to reduced vibrations and improved fuel efficiency, making it not only powerful but also economical to operate.

One of the standout features of the Cub Cadet 18HP is its innovative Cub Cadet signature cutting deck. The tractor is equipped with a 42-inch or 50-inch cutting deck, meticulously designed for superior grass cutting and discharge. This cutting system features twin blades that deliver an exceptional cut quality while reducing clumping and providing optimal air flow. The adjustable cutting height allows users to customize the grass length to their preference, ensuring a well-manicured lawn.

Incorporating advancements in technology, the Cub Cadet 18HP is equipped with a hydrostatic transmission. This feature provides smooth and effortless speed control, allowing homeowners to easily navigate around their properties without the need for constant gear shifting. Whether tackling inclines or navigating tight spaces, the hydrostatic transmission ensures maximum control and maneuverability.

Comfort is also a priority with the Cub Cadet 18HP. The tractor boasts a spacious, ergonomically designed seat that offers excellent support during extended use. Additionally, the easy-to-reach controls and cup holder enhance the overall user experience. Built-in headlights provide visibility for early morning or late evening mowing sessions, ensuring that users can work with ease at any time of day.

For those looking to expand the functionality of their tractor, the Cub Cadet 18HP supports a variety of attachments. From baggers to snow blades and tillers, this versatility allows users to tackle different tasks throughout the seasons, making it a true all-in-one gardening solution.

In summary, the Cub Cadet 18HP stands out in its category for its powerful engine, innovative cutting deck, hydrostatic transmission, and user-centric design. This garden tractor promises durability and efficiency, making it an indispensable tool for anyone serious about lawn care. Whether you are a weekend warrior or a landscaping professional, the Cub Cadet 18HP is built to handle the job with ease and reliability.
Top Page Image Contents