Graco Inc 308-505, 800-164, 800-290, 800-165, 800-367, 2040, 1535 manual Replacing the Oil Seals

Page 16

GEAR REDUCER SERVICE (2040)

WARNING

To reduce the risk of serious bodily injury, including fluid injection, splashing in the eyes or on the skin or injury from moving parts, always follow the Pressure Relief Procedure Warning on page 2 before proceeding.

Replacing the Gasket

NOTE: To maintain a good seal, the gasket must be replaced whenever the gear reducer is disassembled.

1.Remove the four bolts and lockwashers, washers and pull the pump and gear reducer assembly of f the engine.

2. Drain the gear reducer oil by placing a container under it and removing the drain plug with a 22 mm wrench. Replace the o–ring if damaged.

3.Remove the nine screws with a 6 mm wrench and pull the gear case off the gear cover.

4.Remove the old gasket. Clean the gear cover and

case surface. Lightly coat the new gasket

with

grease and install it in on the gear case.

 

5.Follow steps 5 through 7 under Assembling the Gear Reducer if this is all the service required.

Replacing the Oil Seal

NOTE: The oil seal MUST be replaced if removed.

1.Follow steps 1 and 3 under Replacing the Gasket.

2.Remove the snap ring from the gear case, using a snap ring pliers. Pull the gear and bearing.

3.Push the seal from the inside to the outside of the gear case by placing screwdriver against the seal and lightly tapping it with hammer.

4.Wipe the inner surface of the case clean, then lightly coat it with grease. Place the oil seal into the gear case. Use a socket, placed against the surface of the seal, to push the seal into the case until its top surface is past the ridge in the bore.

5.Place the gear and bearing back into the gear case and install the snap ring.

6.Follow steps 4 through 7 under Assembling the Gear Reducer if this is all the service required.

Replacing the Oil Seals

1.Follow steps 1 through 3 under Replacing the Gasket.

2.Loosen the setscrew, using a 4 mm wrench, and pull the gear off the pump with a gear puller.

3.Using a 6 mm wrench, remove the four screws. Be sure to keep them separate from the other nine screws removed previously.

4.Remove the four oil seals and replace them.

5.Follow steps 2 through 7 under Assembling the Gear Reducer if this is all the service required.

Replacing the O–Ring

1.Follow the instructions under Replacing the Gasket and Replacing the Oil Seals to disassemble the gear reducer.

2.Pull the gear cover of f the pump and replace the o–ring.

3.Follow instructions under Assembling the Gear Reducer if this is all the service required.

Assembling the Gear Reducer

1. Grease the o–ring and make sure it’ s properly placed on the gear cover.

2.Place the four oil seals and screws in the gear cover. Place the o–ring on the screw to hold it in the cover.

3.Apply low strength Loctite r (blue) on the screw threads, align the screws with the holes in the pump, and tighten the screws oppositely and evenly.

4.Grease the pump shaft. Align the gear’s slot with the key on the pump shaft and slide the gear onto the shaft, up to the pump’s shoulder. Apply low strength Loctiter on the setscrew threads and tighten the setscrew to lock the gear on the shaft.

5.Make sure the gasket is in place (refer to step 4 under Replacing the Gasket). Install the gear cover on the case, aligning the holes, and secure it with

the nine screws and lockwashers. T

ighten the

screws evenly in a crisscross pattern.

 

6.Grease the engine shaft. Align the gear ’s slot with the key on the engine shaft and slide the gear reducer onto the shaft, up to the engine’s shoulder.

7.Secure the gear reducer to the engine with the four bolts, lockwashers, and washers.

￿￿8￿￿￿￿ 16

Image 16
Contents HYDRA-CLEAN1535 Pressure Washer General Safety Pressure Relief ProcedureSpray Gun Safety Devices Medical TreatmentHose Safety Equipment Misuse HazardFuel and Emission Hazards System PressureMoving Parts Hazard TermsInstallation Set UpCheck for Shipping Damage Connect to Water SupplyStartup Trigger Safety Latch Installing and Changing Spray TipsMaintenance SHUTDOWN, Flushing and StorageTroubleshooting Chart Problem800-164 & 800-290 Hydra-Cleanr2040 Pressure Washer Parts DrawingParts List Part Description QTY800-165 & 800-367 Hydra-Cleanr1535 Pressure Washer Parts List Gear Reducer Service Replacing the O-RingReplacing the Gasket Replacing the Oil SealParts Drawing 802-266 Gear Reducer Replacing the Oil Seals Parts Drawing 802-143 Gear Reducer Pump Assembly, 1500 psi Ring Pump Assembly, 2000 psi CAP Washer Valve Assembly Pump Service ValvesPumping Section Servicing the PlungersTechnical Data AccessoriesServicing the V-Packings Graco Warranty Graco INC. P.O. BOX 1441 MINNEAPOLIS, MN