Euro-Pro VPW43 owner manual Using the High Pressure Lance, Using the Brush With the Trigger Gun

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

Using the High Pressure Lance

The high pressure lance may be used alone or with the detergent applicator bottle.

Add detergent to the bottle and then attach the detergent applicator bottle to the high pressure lance, just push it on the end of the high pressure lance. (Fig. 11 & 12) To remove the detergent applicator bottle, lift the tab on the top of the connector and pull off.

Fig. 11

Fig. 12

Using the Brush With the Trigger Gun

The brush is used with the trigger gun. Push the brush onto the trigger gun nozzle and turn clockwise to lock as you would for the lances. (Fig. 13) The brush may be used for washing cars, boats, windows and other similar items. The brush operate at open orifice pressure so that they will not direct a stream of water.

Fig. 13

Maintenance & Cleaning

Lubrication: The pressure washer is supplied with a closed lubrication system, so no addition of oil is needed. Checking the Water Intake Filter: The water intake filter is located inside the water intake connector. (Fig. 14). Remove periodically and inspect for any deposits that might accumulate there.

Hose Connector

Water Intake

Fig. 14

Cleaning the Nozzles: If you notice that the output pressure fluctuates, you may have to clean the nozzles. Turn the unit "Off". Unplug from electric outlet and disconnect the water supply. Remove the lances, trigger gun and hose from unit. Take the small metal pin provided and insert into the nozzle end to remove any obstructions. (Fig. 15)

Fig. 15

This will occur more frequently if your water supply is very hard.

Storing Your Pressure Washer

When you have finished using your pressure washer, follow these steps for safe storage:

1.Turn the pressure washer to the "Off" position.

2.Turn off the water supply.

3.Before disconnecting the high pressure hose connection, point the trigger gun in a safe direction away from you and discharge the high pressure water. Disconnect the high pressure hose from the pressure washer and trigger gun.

4.Disconnect garden hose from pressure washer.

5.Remove excess water from the pump by tipping the unit on both sides to drain any remaining water from the water intake and outlet fittings.

6.Drain detergent applicator bottle and flush with clean water.

7.Wipe away any remaining water on all parts and fittings.

8.Engage the trigger gun safety lock.

9.Store the unit and accessories in a room above 32°F.

Winterizing & Long Term Storage

1.Disconnect all water connections.

2.Turn the pressure washer on for a few seconds, until any remaining water in the pump exits.

3.Turn the unit off immediately.

4.Store the pressure washer, parts and accessories in an area with a temperature above 32°F.

Suitable Use of Your Pressure Washer

This high pressure washer is suitable for non-professional use. The working temperature must range between 40°F and 120 °F. The machine is supplied with a trigger gun, equipped with a trigger handle to offer a comfortable working position.

The high pressure washer is suitable for washing with cold water only. The water that you use for the pressure washer must not be dirty, sandy or contain any corrosive chemical products.

The pressure washer may be used to wash shutters, doors, tiles, cars, decks, campers, etc., where high water pressure is necessary to remove dirt.

With the detergent applicator bottle, the pressure washer can be used to apply a thick coating of aerated detergent to the areas being cleaned .

When using the pressure washer we recommend the use of personal safety items to reduce the risk of accidental injury.

Unpacking Your Pressure Washer

After you open the package, check to make sure that all the parts are in the box as pre parts that illustrated on page 3 of this guide. Due to transport and packing restraints, some accessories may be supplied unassembled; in this case follow the assembly instructions in this manual. If you have any questions, call EURO- PRO Operating LLC customer service at 1 (800) 798-7398. Keep all small and potentially harmful parts of the package (plastic bags, foamed polystyrene, nails, etc.) out of the reach of children.

Correct Use of the Pressure Washer

•Place the pressure washer in a safe area and on a horizontal surface.

•When using the pressure washer, hold the trigger gun firmly with one hand on the handle and the other on the lance. (Fig. 1)

Fig. 1

•NEVER point the water jet at electric wiring, at the pump unit, or at any person or animal.

Assembling the Pressure Washer Trolley

1.Carefully take all the trolley parts and place together on a flat, stable surface.

2.Insert the two (2) legs into the support brackets on the unit and secure with two (2) of the 1/2-inch #8 Phillips screws provided. (Fig. 2)

Fig. 2

3.Insert the handle into the handle bracket and secure with two (2) of the 1-inch #8 Phillips screws provided. (Fig. 3)

Fig. 3

7

4