Briggs & Stratton 020244-0 Add Engine Oil and Fuel, Connect Hose and Water Supply to Pump

Page 7

CleanShot™ 2050 PSI Pressure Washer

Add Engine Oil and Fuel

• Place pressure washer on a level surface.

CAUTION

Any attempt to crank or start the engine before it has been properly filled with the recommended oil will result in equipment failure.

•Refer to engine manual for oil and fuel fill information.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

•Refer to engine owner’s manual and follow oil and fuel recommendations and instructions.

NOTE: Check oil often during engine break–in. Refer to engine owner’s manual for recommendations.

Figure 6 — Connect the Garden Hose to Water Inlet

Inspect inlet

screen, DO NOT use if damaged;

clean if dirty.

4.Run water through your garden hose for 30 seconds to clean out any debris.

IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 100°F).

5.Connect the garden hose (not to exceed 50 feet in length) to the water inlet.Tighten by hand (Figure 6).

Connect Hose and Water Supply to Pump

IMPORTANT: To avoid pump damage, you must assemble the nozzle extension to the spray gun and attach all hoses before you start the engine.

NOTE: Remove and discard the shipping caps from the pumps high pressure outlet and water inlet before attaching hoses.

1.Uncoil high pressure hose and attach one end of hose to base of spray gun (Figure 4).Tighten by hand.

Figure 4 — Connect High Pressure Hose to Spray Gun

Connect high pressure

hose here

2.Attach other end of high pressure hose to high pressure outlet on pump (Figure 5).Tighten by hand.

Figure 5 — Connect High Pressure Hose to Pump

3.Before connecting garden hose to water inlet, inspect inlet screen (Figure 6). Clean screen if it contains debris or have it replaced if damaged. DO NOT RUN PRESSURE WASHER IF INLET SCREEN IS DAMAGED.

CAUTION

There MUST be at least ten feet of unrestricted garden hose between the pressure washer inlet and any flow shut off device, such as a ‘Y’ shut-off connector or other convenience-type water shut-off valve.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

6.Turn ON the water and squeeze the trigger on the gun to purge the pump system of air and impurities.

WARNING

High pressure spray can cause paint chips or other particles to become airborne.

•Always wear eye protection when using this equipment or in vicinity of where equipment is in use.

•Before starting the pressure washer, be sure you are wearing adequate eye protection.

Checklist Before Starting Engine

Review the unit’s assembly to ensure you have performed all of the following.

1.Make sure handle is in place and secure.

2.Check that oil has been added to proper level in the engine crankcase.

3.Add proper gasoline to fuel tank.

4.Check for properly tightened hose connections.

5.Check to make sure there are no kinks, cuts, or damage to high pressure hose.

6.Provide a proper water supply at an adequate flow.

7.Be sure to read “Safety Rules” and “How To Use Your Pressure Washer” before using pressure washer.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 2050PSI Safety Rules Table of ContentsEquipment Description Operate pressure washer only outdoors When Adding FuelHigh pressure spray may damage fragile items including glass Pump equipped with Know Your Pressure WasherAutomatic Cool Down System Remove Pressure Washer From Carton AssemblyCarton Contents Preparing Pressure Washer for USEAdd Engine Oil and Fuel Checklist Before Starting EngineConnect Hose and Water Supply to Pump Pressure Washer Clearance HOW to USE Your Pressure WasherHow to Start Your Pressure Washer Pressure Washer LocationHow to Use the Adjustable Nozzle How to Stop Your Pressure WasherTo apply detergent, follow these steps Applying Detergent with the Adjustable NozzleUsage Tips Thermal Relief Cleaning Detergent Siphoning TubePressure Washer Rinsing Automatic Cool Down SystemGeneral Maintenance Recommendations SpecificationsPressure Washer Maintenance Check In-Line Filter Nozzle MaintenanceOrifice Changing Pump Oil Engine MaintenanceRing Maintenance Pump MaintenanceProtecting the Pump Always wear eye protection when using PumpSaverPreparing the Unit for Storage Storing the EngineProblem Cause Correction TroubleshootingYear Consumer Use Years Years orAdvertencia Conserve Estas Instrucciones Tabla DE ContenidosDescripción DEL Equipo Reglas DE SeguridadCuando Añada Combustible Precaución Calcomanía Ejemplar de Datos no mostrado, el trasero Conozca SU Maquina Lavadora DE PresionTapa del Depósito del Aceite Llene el motor con aceite Contenido de la Caja MontajePreparando EL Lavador a Alta Presión Para SU USO Remueva el Lavador a Presión del EmpaqueDeposite la gasolina adecuada en el tanque del combustible Agregar Aceite al Motor y GasolinaConecte la Manguera y el Suministro de Agua a la Bomba Lista de Revision Previa al Arranque del MotorEspacio Libre Alrededor del Lavadora a Presión Cómo Usar SU Máquina Lavadora a PresiónUbicación del Lavadora a Presión Cómo Darle Arranque a su Máquina Lavadora a PresiónCómo Usar la Boquilla Ajustable Cómo Detener su Máquina Lavadora a PresiónPara aplicar el detergente, siga los siguientes pasos Aplicación del Detergente Usando la Boquilla AjustableUso Inclina Para Enjuage Enjuage de la Máquina Lavadora a PresiónLimpiando el Tubo Sistema de Enfriamiento Automático Alivio TérmicoRecomendaciones Generales EspecificacionesMantenimiento DE LA Maquina Lavadora a Presion Mantenimiento de los Anillos O Mantenimiento de la BoquillaMantenimiento de la Bomba Proteger la Bomba Mantenimiento DEL MotorPreparando LA Unidad Para SU Almacenamiento Almacenando EL MotorReparacion DE Averias Garantía Limitada

020244-0 specifications

The Briggs & Stratton 020244-0 is a powerful and versatile engine widely recognized in the small engine market. Known for its reliability and robust performance, this engine is a favored choice for various applications, including lawn mowers, generators, and other outdoor power equipment.

One of the key features of the Briggs & Stratton 020244-0 is its compact design, which allows for easy installation in different types of machinery. This engine is built with durability in mind, featuring a cast iron cylinder sleeve that contributes to its longevity and resistance to wear. The aluminum alloy construction not only keeps the weight down but also enhances heat dissipation, ensuring the engine operates efficiently even during prolonged use.

The engine comes equipped with the latest overhead valve (OHV) technology, which improves fuel efficiency and provides better torque. The OHV design allows the engine to breathe better, resulting in smoother operation and lower emissions. This is particularly advantageous for eco-conscious consumers looking to reduce their carbon footprint.

Another notable characteristic of the 020244-0 is its easy starting mechanism. It features a recoil start system that is simple and reliable, ensuring users can get their equipment running with minimal effort. Additionally, the engine is designed with a quiet operation in mind, making it suitable for residential areas where noise levels may be a concern.

Maintenance is made simple with the Briggs & Stratton 020244-0. It has accessible air and oil filters, allowing users to perform routine checks and services without the hassle of complicated disassembly. The engine also features an integrated fuel shut-off valve, which helps in the prevention of fuel leaks and enhances safety during storage.

Overall, the Briggs & Stratton 020244-0 combines innovative technology, ease of use, and a commitment to durability. Whether you are a homeowner tending to your lawn or a professional in the landscaping business, this engine provides the reliability and performance necessary to get the job done effectively. The blend of features and specifications makes the 020244-0 a staple choice in the small engine category, ensuring it continues to serve users for many years.
Top Page Image Contents