Zenoah BKZ5000DL owner manual If Someone Comes, Maintenance, Handling Fuel, Transportation

Page 7

BKZ4500DL / BKZ5000DL

5. For safe operation

IF SOMEONE COMES

1.Guard against hazardous situa- tions at all times. Warn adults to keep pets and children away from the area. Be careful if you are ap- proached. Injury may result from flying debris.

2.If someone calls out or otherwise interrupts you while working, al- ways be sure to turn off the en- gine before turning around.

MAINTENANCE

1.In order to maintain your product in proper working order, perform

the maintenance and checking operations described in the manual at regular intervals.

2. Always be sure to turn off the en- gine and disconnect the spark plug wire before performing any maintenance or checking proce- dures.

WARNING

The metallic parts reach high tem- peratures immediately after stop- ping the engine.

3.When replacing the cutting at- tachment or any other part, or

when replacing the oil or any lu- bricant, always be sure to use only ZENOAH products or products which have been cer- tified by ZENOAH for use with the ZENOAH product.

4.In the event that any part must be replaced or any maintenance or repair work not described in this manual must be performed, please contact a representative from the store nearest ZENOAH authorized servicing dealer for assistance.

5.Do not use any accessory or at- tachment other than those bear- ing the ZENOAH mark and rec- ommended for the unit.

6.Under no circumstances should you ever take apart the product or alter it in any way. Doing so might result in the product be- coming damaged during opera- tion or the product becoming un- able to operate properly.

HANDLING FUEL

1.The engine of the ZENOAH prod- uct is designed to run on a mixed

fuel, which contains highly flam-

 

mable gasoline. Never store cans

G

of fuel or refill the tank of the unit

B

in any place where there is a

 

boiler, stove, wood fire, electrical

 

sparks, welding sparks, or any

 

other source of heat or fire which

 

might ignite the fuel.

 

2.Never smoke while operating the unit or refilling its fuel tank.

3.When refilling the tank, always turn off the engine and allow it to

cool down. Take a careful look around to make sure that there are no sparks or open flames any- where nearby before refueling.

4.Wipe spilled fuel completely us- ing a dry rag if any fuel spillage occurs during refueling.

5.After refueling, screw the fuel cap back tightly onto the fuel tank and then carry the unit to a spot 3 m or more away from where it was refueled before turning on the en- gine.

TRANSPORTATION

1. When hand-carrying the product, cover over the cutting part if nec- essary, lift up the product and carry it paying attention to the blade.

2. Never transport the product over rough roads over long distances by vehicle without removing all fuel from the fuel tank. If doing so, fuel might leak from the tank dur- ing transport.

GB-7

Image 7
Contents BKZ4500DL BKZ5000DL Wear head, eye and ear protection Explanation of Symbols and Safety WarningsParts location ContentsBKZ4500DL BKZ5000DL SpecificationSymbols on the machine ModelWorking Plan For safe operationWorking Condition Working CircumstanceBefore Starting Engine Using the ProductStarting the Engine Transportation MaintenanceIf Someone Comes Handling FuelSet up Fuel Stopping Engine OperationStarting Engine Cutting head will start rotating upon the en- gine startsPutting on the Unit Adjusting Throttle CableAdjusting Idling Speed Cutter Application ChartTrimming Grass and Weeds Cutting MethodControlling Blade Bounce Cutting Work Line Head UsagePoint MaintenanceAdjusting the Line Length BladeFuel Filter Replacement Plug is a NGK CMR7HRefilling Trimming Line AIR FilterAngle Transmission Procedures to be Performed After Every 100 Hours of USEStorage DisposalLimited warranty Troubleshooting guideCheck Probable Causes Action