Ryobi 454 manual Model, 747-1152

Page 17

747-1152

Model 454

	Ref.	Part No.	Part Description
	No.	Part No.	Part Description
	No.

	1.	747-1152	Shift Rod
	2.	649-0041	Upper Handle Ass’y
	3.	649-0034	Lower Handle Ass’y
	4.	710-3005	Hex Screw 3/8-16 x 1.25
	5.	710-3056	Hex Screw 5/16-18 x 3.25
	6.	711-0415	Clevis Pin 3/8-1.62
	7.	712-0379	Flange Lock Nut 3/8-24
	8.	712-0429	Hex Lock Nut 5/16-18
	9.	714-0147	Cotter Pin
	10.	720-0313	Grip
	11.	720-0210A	T-Knob
	12.	720-0278A	Foam Grip
	14.	726-0317	Cable Tie
	15.	735-0246	End Plug
	16.	736-0117	Flat Washer 3/8 ID x.620 OD
	17.	736-0242	Bell Washer.340 ID x.872 OD
	18.	738-0958	Shoulder Spacer
	19.	784-0190	Handle Adjustment Crank
	20.	784-0191	Hex Nut Retainer Bracket
	21.	786-0120	Depth Stake
	22.	747-1219	Clutch Bail
	23.	786-0181	Shift Rod Lever
	24.	686-0044A	End Cover Ass’y
	25.	710-0176	Hex Cap Screw 5/16-18 x 2.75
	26.	710-3008	Hex Cap Screw 5/16-18 x.750
	27.	710-3097	Carriage Bolt 3/8-16 x 1.0
	28.	712-0421	Wing Nut
	29.	736-0169	Lock Washer 3/8

30.712-3004A Flange Nut 5/16-18

31.	726-0106	Cap Nut
32.	738-0849	Hex Screw 5/16-18 x.75”
33.	747-0432	Rod

	Ref.	Part No.	Part Description
	No.

34.750-0885A Spacer.322 x.625 x 2.0

35.	786-0090	Side Shield
36.	786-0113	Rear Tine Shield
37.	786-0176	RH Handle Mounting Bracket
38.	786-0177	LH Handle Mounting Bracket
39.	786-0178	Tine Shield
40.	786-0179	Tine Shield Bracket
41.	786-0180	Front Tine Shield Scraper Bracket
42.	686-0109	Shift Crank Ass’y
44.	710-1017	Screw 1/4-14 x.625
46.	715-0120	Spiral Pin 3/16 x 1.0
49.	784-0208C	Shift Cover
50.	784-0160	Tine Adapter Ass’y
51.	712-3054	Hex Nut 3/8-24
53.	742-0305	13” Articulating Tine
54.	738-0689	Shoulder Bolt
55.	736-0208	Flat Washer.51” ID x 1.50” OD
56.	736-0253	Bell Washer.515” ID x 1.14” OD
57.	738-0688	Shoulder Bolt
58.	784-0205	Tine Ass’y Complete
59.	714-0149B	Internal Cotter Pin
60.	735-0127	Rubber Washer
61.	714-0104	Cotter Pin
62.	710-3022	Hex Screw 3/8-16 x 2.75”
63.	736-0204	Flat Washer
64.	712-0431	Flange Nut.344 ID x.62 OD
65.	736-0169	Lock Washer
66.	712-0798	Hex Nut 3/8-16
67.	710-0946	Truss Screw 1/4-20 x.65
68.	712-0324	Hex Lock Nut 1/4-20
69.	726-0273	Battery Hose Clamp 5/16
70.	736-3090	Flat Washer.260 ID x.720 OD

17

Image 17

Contents Rear Tine Tiller Operator’s ManualModel MTD LLC P.O. BOX 361131 CLEVELAND, OHIOFINDING MODEL NUMBER TABLE OF CONTENTSCUSTOMER SUPPORT The answer you areTraining SECTION 1 IMPORTANT SAFE OPERATION PRACTICESPreparation OperationYour Responsibility Maintenance & StorageO U T C U TAttaching Handle Assembly Before AssemblySECTION 2 ASSEMBLING YOUR TILLER To Remove Unit From CartonAttaching Control Rod Final Clutch AdjustmentTire Pressure SECTION 3 KNOW YOUR TILLERGear Selection Handle NeutralSECTION 4 OPERATING YOUR TILLER Handle Adjustment CrankClutch Control Throttle ControlOperating the Tiller Setting The DepthTo Stop Engine Belt Tension Adjustment Handle AdjustmentEngine Adjustment SECTION 6 MAINTAINING YOUR TILLERBelt Replacement Cleaning Tine AreaOff-SeasonStorage Wheel ShaftsTrouble SECTION 7 TROUBLE SHOOTING GUIDEPossible Causes Corrective ActionPage SECTION 8 PARTS LIST FOR MODEL Part Description ModelModel 747-1152 Model 686-0111 MANUFACTURER’S LIMITED WARRANTY FOR