Sears 917.299642 Ground Drive Belt Replacement, Belt Capguard, Nut, Hairpin Clip Rivet

Page 18

SERVICE AND ADJUSTMENTS

,ll,

GROUND DRIVE BELT REPLACEMENT

-Remove Hairpin Clip and Retaining Pin from Hub of left hand Wheel Pull Wheel out from Tiller about I inc_h__

-Remove Belt Guard by removing two (2) Cap Nuts, one

(1) Hex Nut and three (3) Washers so that the Belt Guard can slide straight out away from the Engine (Fig. 28).

BELT

CAPGUARD

NUT

NUT

HEX (LOCATED BEHIND TIRE)

HAIRPIN CLIP

AND RIVET

FIGURE 28

Loosen Belt Guides "A" and "B", and also Nuts "C" and "D" (Fig. 29)°

Remove old Belt by slipping from Engine Pulley firsL

Place Belt in groove of Transmission Pulley and into

oove of Engine Pulley,rBELT MUST BE tN GROOVE N TOP OF IDLER PULLEY_ NOTE POSITION OF

BELT TO GUIDES.,

Tighten Belt Guides "A" and "B" and Nuts "C" and "D".

Replace Belt Guard, Washers, Cap Nuts, and Hex NuL

- Reposition Wheel and replace Retaining Pin and Hair- pin Cfip_

GROUND DRIVE BELT ADJUSTMENT

For proper belt tension, the Extension Spring should have about 518 inch stretch with Drive Control Bar in "EN-

GAGED" position_ This tension can be obtained as fol- lows:

Loosen Cable Clip Screw securing the Drive Control Cable (Fig. 29 - INSET A)..

Slide Cable forward for less tension and rearward for more tension until about 5/8 inch stretch is obtained while the Drive Control Bar is engaged (Fig. 29 - INSET B)_

Tighten Cable Clip Screw securely_

BELT

BELT

CABLE CLIP

GUIDE"B"

GUIDE"A"

SCREW

DRIVE CONTROL

CABLE

INSET A

INSET B

EXTENSION LESS

SPRINGTENSION

ENGINE

PULLEY

MORE

TENSION

NUT "D"

\

 

IDLER

TRANSMISSION

 

PULLEY

 

 

PULLEY

 

 

FIGURE 29

18

Image 18
Contents Swaurs OwnersPreparation Maintenance and StorageTraining OperationOIL 20 OZ. Capacity Product SpecificationsMaintenance Agreement WorkmanshipTable of Contents Engine Tiller AccessoriesTiller Maintenance Tiller PerformanceAssembly Your BAG of Parts will Consist of the FollowingGearcase Handle Lock Install HandleGearcase Gearcase Notch Handle Lock FlatAdjustments Attach this END To Shift Lever IndicatorHairpin Clipindicator Connect Shift RODDepth Safety DecalMeets ANS! Safety Requirements Stake Leveling ShieldHOW to USE Your Tiller Operation Tank or Permanent Damage MAY Occur To Start EngineFill Fuel Tank TILLING/CULTIVATING TipsRetaini Adjust Wheels for CultivatingCultivating CLIP\Maintenance Transmission FinishOIL Drain Plug Level OIL Filler Service Recommendations Service RecordService Dates Service and Adjustments Position HandleTire Care Belt Capguard Ground Drive Belt ReplacementGround Drive Belt Adjustment NUTService and Adjustment Tine ReplacementChecking Adjustment Mixture AdjustmentIdle RPM Adjustment Throttle Control Cable AdjustmentSoil Balls UP or Clumps Engine Misses or Lacks PowerStorage StoragePage KEY Part Description Repair PartsP. Craftsman Tiller Grommet, HandleNOo P. Craftsman Tiller Model NumberMAINFRAME, Left Side 104679XP. Craftsman Tiller Model Number MAINFRAME, Right Side TireRepair Parts P, Craftsman Tiller Model NumberTine Shield NO. no4460J Tine, R H,Outer Tines6555J Tine, R. H. Inner Clip, HairpinBall, Clutch Installation 94153223087 Engine Briggs & Stratton -- Model Number 112202, Type Number ENGINE, Rear KEY Part Description Retainer Link93543 776 Gasket SETPlug Oil Description KEY Part391737 90576Lll£Vl@l 1II@?!i8 IIIi£VIGII £RRFTXMaN Part Description

917.299642 specifications

The Sears 917.299642 is a powerful and versatile lawn tractor that has garnered attention for its reliability and innovative features. Designed with homeowners and landscaping enthusiasts in mind, this machine excels in various outdoor applications, including mowing, mulching, and snow removal.

One of the standout features of the Sears 917.299642 is its robust engine. Typically equipped with a dependable Briggs & Stratton or Kohler engine, the tractor provides ample power to tackle even the toughest terrain. The engine is designed for optimal performance, featuring easy starting mechanisms and efficient fuel consumption, allowing users to work longer without frequent refueling breaks.

The cutting deck of the Sears 917.299642 is another highlight. With a wide cutting width, often around 42 to 54 inches depending on the model variant, it ensures efficient mowing of medium to large lawns. The deck is made with durable materials to resist wear and tear, while its adjustable height settings allow users to customize the mowing height according to their lawn's needs.

One of the notable technologies incorporated in the Sears 917.299642 is its hydrostatic transmission. This feature allows for smooth and effortless speed adjustments, providing a more intuitive driving experience. Operators can simply press the pedal to accelerate or decelerate, eliminating the need for manual shifting and making it easier to navigate around obstacles.

Furthermore, the Sears 917.299642 is designed with user comfort in mind. The ergonomic seat is padded and adjustable, ensuring that operators can find their ideal driving position. The tractor also features a reliable steering system, making it easy to maneuver, even in tighter spaces.

In terms of build quality, the Sears 917.299642 is constructed with a robust frame and heavy-duty components, ensuring longevity and durability. Whether used for regular mowing or more demanding tasks, this lawn tractor is built to last.

Maintenance ease is another characteristic that sets the Sears 917.299642 apart. With easily accessible components, including the engine and mower deck, routine servicing and repairs can be performed with minimal hassle. This feature greatly appeals to homeowners looking for low-maintenance outdoor equipment.

In summary, the Sears 917.299642 offers a combination of power, versatility, and user-friendly design, making it an excellent choice for homeowners seeking a reliable lawn tractor to maintain their outdoor spaces.