Poulan PRRT850X manual Service and Adjustments, Tiller, Tire Care

Page 14

SERVICE AND ADJUSTMENTS

CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug.

TILLER

TO ADJUST HANDLE HEIGHT (See Fig. 20)

Select handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil.

•First loosen handle lock lever.

•Handle can be positioned at different settings between “HIGH” and “LOW” positions.

•Retighten handle lock lever securely after adjusting.

HANDLE

(HIGH POSITION)

HANDLE LOCK LEVER

HANDLE

(LOW POSITION)

FIG. 20

TIRE CARE

CAUTION: When mounting tires, un- less beads are seated, overinflation can cause an explosion.

•Maintain 20 PSI (1.4 kg/cm2) of tire pressure. If tire pressures are not equal, tiller will pull to one side.

•Keep tires free of gasoline or oil which can damage rubber.

TO REMOVE WHEEL (See Fig. 21)

•Place blocks under transmission to keep tiller from tipping.

•Remove outer side shield by removing nuts “A” and “B”.

•Remove inner side shield by removing nuts “C” and “D”.

•Remove hairpin clip and clevis pin from wheel.

•Remove wheel and tire.

•Repair tire and reassemble.

CLEVIS

 

PIN

 

NUT “C”

 

NUT

 

“D”

 

HAIRPIN

 

CLIP

 

NUT “B”

 

NUT “A”

INNER SIDE

OUTER SIDE

SHIELD

SHIELD

 

FIG. 21

TO REMOVE BELT GUARD (See Fig. 22)

NOTE: For ease of removal, remove hairpin clip and clevis pin from left wheel. Pull wheel out from tiller about 1 inch.

•Remove two (2) screws from side of belt guard.

•Remove hex nut and washer from bottom of belt guard (located behind wheel).

•Pull belt guard out and away from unit.

•Replace belt guard by reversing above procedure.

BELT GUARD

SCREW

AND WASHER

 

HEX NUT AND WASHER (LOCATED BEHIND TIRE)

SCREW

 

AND

HAIRPIN CLIP AND

WASHER

CLEVIS PIN

FIG. 22

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents PRRT850X Training Safety RulesMaintenance and Storage PreparationTable of Contents OPERATOR’S Position See Fig AssemblyTools Required for Assembly Install Handle See Figs , 4, Unpacking Carton See FigRemove Tiller from Crate Attach Clutch Cable See FigConnect Shift ROD See Fig Check Tire PressureKnow Your Tiller Meets Ansi Safety RequirementsOperation HOW to USE Your Tiller ADD Gasoline To TransportBefore Starting Engine Cultivating Tine Shear PinsTilling Hints General Recommendations MaintenanceLubrication Chart Before Each USETo Change Engine OIL See Figs AIR Cleaner See FigEngine Muffler CleaningCooling System See Fig Spark PlugTire Care Service and AdjustmentsTiller Ground Drive Belt Adjustment See Fig To Replace Ground Drive Belt See FigsTine Replacement See Figs , 25, To Adjust Throttle Control Cable See Fig To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points Service Notes Limited Warranty HOPParts and Service Changere DE Pièces LES ET L’ENTRETIEN Limitée Garantie Dépannage DE Guide Moteur EntreposageSupplementaire Information MotobineuseCarburateur LE Régler Pour Réglages ET RévisionMoteur 27 .FIG25 .FIG 24 .FIG 26 et 2526 .FIG Courroie LA Remplacer Pour Fig la Voir Terre À D’ENTRAÎNEMENT Courroie LA Régler23 et 22 .fig les Voir Terre À D’ENTRAÎNEMENTDE Protecteur LE Enlever Pour Fig la Voir Roue LA Enlever PourFig la Voir Roiecour Fig la Voir’ALLUMAGE Bougie EntretienNettoyage SilencieuxFig la Voir AIR À Filtre LubrificationLubrification Générales RecommandationsLubrification DE Tableau Utilisation Chaque AvantDents DES Cisaillement DE Boulons UtilisationBinage 15 .FIG14 .FIG Labourage DE ConseilsMoteur LE Démarrer Pour 13 .FIG’ESSENCE Réservoir LE Remplir Moteur LE Démarrer DE AvantExtérieurs Latéraux Déflecteurs Transporter PourMENT/LESLESEU ROUES-AVANT Marche BineuseMoto Votre Utiliser Comment LA Avec -FRAISES DES UtilisationAnsi Sécurité DE Exigences AUX Conforme Motobineuse Votre ConnaissezMontage Fig la Voir SetesviFig la Voir Carton LE Deballer Poignee LA InstallerEt 4, 3, .fig les Voir Fig la Voir D’OPERATEUR Position Montage LE Pour Exiges Outils LESProduit DE Spécifications SommaireClient DU Responsabilités Motobineuses des Sécurité toute Sécurité DE RèglesEntreposage ET Entretien En lUtilisation pour ConseilsImportant Manuel

PRRT850X specifications

The Poulan PRRT850X is a robust and efficient tool designed for those who demand quality and performance in their outdoor equipment. As a versatile and powerful trimmer, it has gained popularity among both homeowners and professional landscapers for its reliability and range of features.

One of the standout characteristics of the PRRT850X is its powerful 25cc 2-cycle engine. This engine provides the strength and efficiency needed to tackle tough overgrown lawns and landscaping tasks with ease. It is designed to deliver optimal performance while reducing emissions, making it a more environmentally friendly option in the garden equipment market.

The trimmer features a lightweight and ergonomic design, which significantly enhances user comfort and maneuverability. Weighing in at just over 10 pounds, users can easily handle the tool for extended periods without experiencing fatigue. The adjustable handle allows for personalized setups, further ensuring ease of use.

The dual-line bump feed head is another major highlight of the Poulan PRRT850X. This feature allows for quick and easy line advancement simply by tapping the head against the ground, promoting efficiency during operation. The trimmer is compatible with .095-inch diameter line, suitable for tackling thick grass and weeds without compromising performance.

In addition, the PRRT850X employs advanced technologies such as its Easy Start System, which allows for simple pull starts with minimal effort. This system is particularly beneficial for those who may struggle with traditional starting methods, ensuring a seamless experience right from the beginning.

Additionally, this trimmer boasts a high-impact plastic housing that protects the engine and internal components, ensuring durability and longevity. This feature is essential for those who use the tool in various outdoor conditions, as it maintains performance while withstanding the rigors of heavy use.

The Poulan PRRT850X is also equipped with a straight shaft design, which enhances reach and access to hard-to-reach areas, making it an excellent choice for mowing along fences, walls, and flower beds. It allows for precision trimming and edging, contributing to a well-maintained garden appearance.

Overall, the Poulan PRRT850X combines power, convenience, and durability, making it a valuable addition to any landscaper's toolkit or home gardening equipment. Its thoughtful design and innovative features ensure that users can accomplish their tasks efficiently and effectively, producing professional-quality results every time.
Top Page Image Contents