Poulan PRRT850 manual To Replace Ground Drive Belt See Figs, Ground Drive Belt Adjustment See Fig

Page 15

SERVICE AND ADJUSTMENTS

TO REPLACE GROUND DRIVE BELT (See Figs. 22 and 23)

Remove belt guard as described in “TO REMOVE BELT GUARD”.

Remove old belt by slipping off engine pulley first then remove from transmission pulley.

Place new belt in groove of transmission pulley and into engine pulley. BELT MUST BE IN GROOVE ON TOP OF IDLER PULLEY. NOTE POSITION OF BELT TO GUIDES.

Check belt adjustment as described below.

Replace belt guard.

Reposition wheel and replace clevis pin and hairpin clip.

GROUND DRIVE BELT ADJUSTMENT (See Fig. 23)

For proper belt tension, the extension spring should have about 5/8 inch (16 mm) stretch when drive control bar is in “ENGAGED” position. This tension can be attained as follows:

Loosen cable clip screw securing the drive control cable.

Slide cable forward for less tension and rearward for more tension until about 5/8 inch (16 mm) stretch is obtained while the drive control bar is engaged.

Tighten cable clip screw securely.

CABLE CLIP SCREW

ENGINE

PULLEYDRIVE CONTROL CABLE

LESS

TENSION

 

 

MORE

5/8"

 

TENSION

EXTENSION

IDLERSPRING

PULLEYTRANSMISSION

PULLEY

FIG. 23

15

Image 15
Contents PRRT850 Preparation Safety RulesMaintenance and Storage TrainingTable of Contents OPERATOR’S Position See Fig AssemblyTools Required for Assembly Contents of Hardware PackUnpacking Carton See Fig Install Handle See Figs , 4,Check Tire Pressure Attach Clutch Cable See FigConnect Shift ROD See Fig Remove Tiller from CrateMeets Ansi Safety Requirements OperationKnow Your Tiller HOW to USE Your Tiller To Transport Before Starting EngineADD Gasoline Tine Shear Pins Tilling HintsCultivating General Recommendations MaintenanceMaintenance Schedule Lubrication ChartAIR Cleaner See Fig EngineTo Change Engine OIL See Figs Spark Plug CleaningCooling System See Fig MufflerService and Adjustments TillerTire Care To Replace Ground Drive Belt See Figs Ground Drive Belt Adjustment See FigTine Replacement See Figs , 25, To Adjust Carburetor To Adjust Throttle Control Cable See FigEngine OIL StorageOther Fuel SystemTroubleshooting Points Service Notes HOP Limited WarrantyParts and Service Changere DE Pièces LES ET L’ENTRETIEN Limitée Garantie Dépannage DE Guide Motobineuse EntreposageSupplementaire Information Moteur27 .FIG Réglages ET RévisionMoteur Carburateur LE Régler Pour26 et 25 26 .FIG25 .FIG 24 .FIG Terre À D’ENTRAÎNEMENT Fig la Voir Terre À D’ENTRAÎNEMENT Courroie LA Régler23 et 22 .fig les Voir Courroie LA Remplacer PourFig la Voir Fig la Voir Roue LA Enlever PourFig la Voir Roiecour DE Protecteur LE Enlever PourSilencieux EntretienNettoyage ’ALLUMAGE BougieLubrification Fig la Voir AIR À FiltreLubrification Générales RecommandationsLubrification DE Tableau ’ENTRETIEN Calendrier15 .FIG UtilisationBinage Dents DES Cisaillement DE Boulons13 .FIG Labourage DE ConseilsMoteur LE Démarrer Pour 14 .FIGTransporter Pour Moteur LE Démarrer DE AvantExtérieurs Latéraux Déflecteurs ’ESSENCE Réservoir LE RemplirLA Avec -FRAISES DES Utilisation BineuseMoto Votre Utiliser Comment MENT/LESLESEU ROUES-AVANT MarcheMotobineuse Votre Connaissez Ansi Sécurité DE Exigences AUX ConformeFig la Voir Setesvi MontagePoignee LA Installer Et 4, 3, .fig les VoirFig la Voir Carton LE Deballer Pièces DES SAC DU Contenu Fig la Voir D’OPERATEUR PositionMontage LE Pour Exiges Outils LES Sommaire Client DU ResponsabilitésProduit DE Spécifications En lUtilisation pour Conseils Sécurité DE RèglesEntreposage ET Entretien Motobineuses des Sécurité toutePRRT850