Troy-Bilt 665B manual Troubleshooting, Problem Possible Cause Correction

Page 23

Section 5: Maintenance 23

TROUBLESHOOTING

Before performing any troubleshooting procedures, refer to the appropriate safety, operating or maintenance instructions in this Manual or in the Engine Owner’s Manual. Contact your local authorized engine service dealer for engine service. Contact your local authorized tiller dealer or the factory for all other service problems.

PROBLEM

 

POSSIBLE CAUSE

 

CORRECTION

 

 

 

 

 

 

 

Engine does

1.

Spark plug wire disconnected.

1.

Reconnect wire.

not start.

2.

Engine Throttle Control Lever incorrectly set.

2.

Put lever in START position.

 

3.

Fuel tank empty.

3.

Add fuel.

 

4.

Choke control (if so equipped) in incorrect position.

4.

See Engine Owner’s Manual.

 

5.

Stale gasoline.

5.

Drain fuel and add fresh fuel.

 

6.

Dirty air filter(s).

6.

Clean or replace filter(s).

 

7.

Defective or incorrectly gapped spark plug.

7.

Inspect spark plug.

 

8.

Carburetor out of adjustment.

8.

See Engine Service Dealer.

 

9.

Misadjusted throttle control.

9.

See Engine Service Dealer

 

10.

Dirt or water in fuel tank.

10.

See Engine Service Dealer.

 

 

 

 

 

Engine runs poorly.

1.

Defective or incorrectly gapped spark plug.

1.

Inspect spark plug (see Engine Owner’s Manual).

 

2.

Dirty air filter(s).

2.

Clean or replace (see Engine Owner’s Manual).

 

3.

Carburetor out of adjustment.

3.

See Engine Service Dealer.

 

4.

Stale gasoline.

4.

Replace with fresh gasoline.

 

5.

Dirt or water in fuel tank.

5.

See Engine Service Dealer.

 

6.

Engine cooling system clogged.

6.

Clean air cooling system (see Engine Owner’s Manual).

 

 

 

 

 

Engine overheats.

1.

Engine cooling system clogged.

1.

Clean air cooling area (see Engine Owner’s Manual).

 

2.

Carburetor out of adjustment.

2.

See Engine Service Dealer.

 

3.

Oil level is low.

3.

Check oil level (see Engine Owner’s Manual).

 

 

 

Engine does not

Misadjusted/faulty engine switch.

See Engine Owner’s Manual or Engine Service Dealer.

shut off.

 

 

 

 

 

 

 

 

 

Wheels and Tines

1.

Improper use of controls.

1.

Review Sections 3 and 4.

will not turn.

2.

Forward Clutch: Misadjusted forward clutch control cable.

2. Adjust cable tension (Section 5).

 

3.

Reverse Clutch: Misadjusted clutch control cable.

3.

Adjust cable tension (Section 5).

 

4.

Worn or broken clutch belt(s).

4.

Check belts. Replace parts as needed (Section 5).

 

5.

Internal transmission wear or damage.

5.

Contact local dealer or Factory.

 

6.

Screw and key loose in transmission pulley.

6.

Tighten screw; check that key is in place.

 

 

 

 

 

Tines turn, but

1.

Wheel mounting hardware missing.

1.

Replace hardware.

wheels don’t.

2.

Screw and key loose in transmission pulley.

2.

Tighten screw; check that key is in place.

 

3.

Internal transmission wear or damage.

3.

Contact local Dealer or Factory.

 

4.

Misadjusted wheel gear cable.

4. See Wheel Gear Cable Adjustment, Section 5.

 

5.

Wheel Gear Lever not fully engaged.

5.

Engage lever (see Section 3).

 

 

 

 

 

Wheels Turn, but

1.

Tine holder mounting hardware missing.

1.

Replace hardware.

Tines Don’t.

2.

Internal transmission wear or damage.

2.

Contact local Dealer or Factory.

 

 

 

 

 

Poor tilling

1.

Worn tines.

1.

See Bolo Tines (Section 5).

performance.

2.

Improper Depth Regulator setting.

2.

See Tilling Tips & Techniques, Section 4.

 

3.

Incorrect throttle setting.

3.

See Section 4.

 

4.

Belt(s) slipping.

4.

See Checking Clutch Belt Tension, Section 5.

 

 

 

 

 

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Operator’s Manual Table of Contents Operation Safety Alert SymbolTraining PreparationUse slower engine speeds Maintenance and StorageTo Avoid Serious Injury DecalsAttach Handlebars Hardware BAG Parts ListIntroduction Inspect UnitAttach Forward Clutch Control Cable Attach Reverse Clutch Control CableSecure the wheel gear cable Check AIR Pressure in TiresADD Motor OIL to Engine Attach Wheel Gear LeverForward Clutch Control Levers IntroductionWheel Gear Lever Reverse Clutch ControlRetighten the two screws at the ends of the handlebar To Adjust the Handlebar HeightEngine Controls Starting the Engine PRE-START ChecklistBREAK-IN Operation STARTING/STOPPING EngineEngaged Switch to the OFF positionOperating the Tiller Stopping the EngineLengthwise and then crosswise Tiller along while the tines doYour freshly tilled or cultivated soil Unwanted weed seeds back into Till Freshly tilled groundTerrace Gardening Read the following recommendations before tilling on slopesTilling Up and Down Slopes Vertical Tilling Loading and Unloading the Tiller Clearing the TinesMaintenance Schedule Engine Cleaning CARBURETOR/GOVERNOR Control Adjustments Engine OIL ServiceAIR Cleaner Service Spark Plug ServiceBolo Tines OFF Season StorageChecking and Adjusting Tension on Clutch Belts Checking and Adjusting Forward Clutch Belt TensionRemoving Forward Clutch Belt Checking and Adjusting Reverse Clutch Belt TensionRemoving Reverse Clutch Belt Installing Forward Clutch BeltROW Marker Model OEM-290-257 Installing Reverse Clutch BeltOr pulley HILLER/FURROWER Model OEM-290-250Problem Possible Cause Correction TroubleshootingDrawing no Description Parts List Drawing noPart Description GW-9621 Oil Seal 1909950 Reverse Clutch Cable 4020 Part Description End play on drive shaft Input Pinion Shaft & Gear AssemblyMain Drive Shaft Assembly 712-0375 1904522001 OEM-290-254Bumper OEM-290-254 Row Marker Attachment option OEM-290-257GW-9621 Page TROY-BILT Tiller Lifetime Limited Warranty
Related manuals
Manual 28 pages 9.23 Kb

665B specifications

Troy-Bilt is a trusted name in outdoor power equipment, and their line of tillers, including the E666M, 664D, and 665B models, exemplifies their commitment to quality and practicality. These tillers are designed to make soil preparation easier and more efficient, catering to both amateur gardeners and seasoned landscapers alike.

The Troy-Bilt E666M is a robust machine tailored for ease of use and reliability. With a powerful engine, it delivers consistent performance, ensuring that users can tackle even the toughest soils. One of its standout features is the adjustable tilling width, which provides flexibility for various gardening needs. This tiller also boasts a Reverse Tillage feature, allowing the operator to break up stubborn soil with ease while enhancing control during operation.

The 664D model takes efficiency a step further with its durable construction and user-friendly design. This tiller is equipped with a dependable engine that provides ample power for deep soil cultivation. The 664D features self-propulsion technology, allowing users to maintain steady speed without exerting excessive effort. The adjustable depth settings further enhance soil penetration, making it possible to cultivate deep for extensive planting or surface till for lighter gardening tasks.

With the 665B, Troy-Bilt introduces advanced engineering for increased maneuverability and performance. This tiller features a patented belt-drive system that improves torque and ensures optimal power transfer to the tines. The 665B is also designed with comfort in mind, featuring ergonomic handles that reduce strain on the operator, making it ideal for longer gardening sessions. Its heavy-duty tines ensure exceptional soil mixing, while the adjustable tilling width and depth allow for customization according to specific gardening requirements.

All three tillers come equipped with Troy-Bilt's signature red oversized drag stake, enabling users to control tilling depth and improve stability during operation. They are designed with durable components that promise longevity and reliability, ensuring that they can withstand rigorous use season after season.

In summary, the Troy-Bilt E666M, 664D, and 665B tillers offer a variety of features and technologies that cater to every gardening need. With their reliable engines, user-friendly designs, and advanced tilling capabilities, these models embody the innovation and durability that Troy-Bilt is known for, making them excellent choices for anyone looking to elevate their gardening experience.
Top Page Image Contents