Troy-Bilt E666M-Pony, 664D-Pony manual Battery Maintenance

Page 25

 

Section 5: Maintenance

25

 

 

 

 

 

 

WARNING

Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove the key from the keyswitch on units so equipped.

Failure to follow these instructions can result in serious personal injury or property damage.

BATTERY MAINTENANCE

DANGER

Use extreme caution when working on or near batteries. To help prevent per- sonal injury or property damage:.

Batteries generate explosive gases. Keep sparks and flames away from the battery at all times. Ventilate the area when charging or using the battery in an enclosed area.

Battery Care in Service

The battery is sealed and is maintenance- free. Acid levels cannot be checked.

Always keep the battery cables and ter minals clean and free of corrosive build-up.

After cleaning the battery and terminals, apply a light coat of petroleum jelly or grease to both terminals

Always keep the rubber boot positioned over the positive terminal to prevent

shorting.

Charging

If the tractor has not been put into use for an extended period of time, charge the battery with an automotive-type 12-volt charger for a minimum of one hour at six amps.

Jump Starting

IMPORTANT: Never jump your tiller’s dead battery with the battery of a running vehicle.

1.Connect end of one jumper cable to the positive terminal of the good battery, then the other end to the positive terminal of the dead battery.

2.Connect the other jumper cable to the negative terminal of the good battery, then to the frame of the unit with the dead battery.

Failure to use this procedure could cause sparking, and the gas in either battery could explode.

Cleaning

Clean the battery by removing it from the tractor and washing with a baking soda and water solution. If necessary, scrape the battery terminals with a wire brush to remove deposits. Coat terminals and exposed wiring with grease or petroleum jelly to prevent corrosion.

Battery Failures

Some common causes for battery failure are:

incorrect initial activation

undercharging

overcharging

corroded connections

freezing

IMPORTANT: These failures are NOT covered by your tractor’s warranty.

Battery Removal and Installation

When removing and installing the battery, disconnect and connect the cables in this order to avoid sparking:

1.To remove the battery, first disconnect the negative (-) cable from the grounding screw on the back of the battery bracket post. Bend the cable away from any metal parts.

2.Disconnect the negative (-) cable from the negative (-) battery post.

3.Disconnect the positive (+) cable from the positive (+) battery post and bend it away from any metal parts. Cover the cable terminal with its rubber boot.

4.Remove the battery clamp.

5.To install the battery, reverse the above steps. Be sure that the battery posts face to the rear of the tiller and that the posi- tive (+) post is on the left side as you face forward from the handlebars.

Battery Storage

Charge battery fully. The battery loses some of its charge each day when the unit is not used.

IMPORTANT: NEVER store battery without a full charge. Recharge battery before returning to service or every two months, whichever occurs first.

When storing unit for extended periods, disconnect battery cables. Removing battery from unit is recommended.

Image 25
Contents Operator’s Manual Finding Model Number Table of ContentsCustomer Support Safety Alert Symbol SafetyTraining PreparationSafety Maintenance and StorageKeep children and pets away Use slower engine speedsTo Avoid Serious Injury DecalsHardware BAG Parts List AssemblyIntroduction Inspect UnitAttach Forward Clutch Control Cable Attach Reverse Clutch Control CableAssistance Attach Wheel Gear Lever AssemblyCheck AIR Pressure in Tires Marked NegWheel Gear Lever Features and ControlsForward Clutch Control To Operate the Forward Clutch ControlEngine Controls Features and ControlsReverse Clutch Control Depth RegulatorOperation PRE-START ChecklistStarting and Stopping Engine BREAK-IN OperationOperation Operating the TillerStarting the Engine Stopping the EngineStopping the Tiller and Engine For reverse motion of the wheels and tinesChoosing correct wheel and tine speeds Tilling Tips & TechniquesTilling up and down slopes Tilling across slopes without using terracesTerrace Gardening Loading and Unloading the Tiller Power CompostingMaintenance Schedule MaintenanceCheck Hardware Check Tire PressureTransmission Gear OIL Service MaintenanceCheck for OIL Leaks To Check Transmission Gear Oil LevelEngine OIL Service Engine CleaningAIR Cleaner Service Spark Plug ServiceOFF Season Storage Wheel Gear Cable AdjustmentBolo Tines Cutting Edge Tine Checking and Adjusting Forward Clutch Belt TensionChecking Forward Belt Tension Checking and Adjusting Reverse Clutch Belt TensionRemoving Forward Clutch Belt Installing Forward Clutch BeltInstalling Reverse Clutch Belt Reverse Clutch Belt Removal and ReplacementRemoving Reverse Clutch Belt Battery Maintenance Problem Possible Cause Correction TroubleshootingHILLER/FURROWER Model OEM-290-251 Bumper Model OEM-290-254ROW MARKER- Model OEM-290-257 TROY-BILT Tiller Lifetime Limited Warranty
Related manuals
Manual 40 pages 36.71 Kb Manual 40 pages 24.08 Kb