Troy-Bilt 664D Assembly, Introduction, Inspect Unit, Hardware BAG Parts List, Attach Handlebars

Page 6

6

Section

2

Assembly

WARNING

To prevent personal injury or property damage, do not start the engine until all assembly steps are complete and you

HARDWARE BAG PARTS LIST

Fig.

 

Ref. Qty.

Description

1

2

3/8-16 x 1" Hex Hd. Screw

1

2

3

4

56

have read and understand the safety and

2

1

Keyed Washer

7

89

operating instructions in this Manual.

3

1

Wheel Gear Lever Knob

4

1

Height Adjustment Flange

11

10

INTRODUCTION

Carefully follow these assembly steps to correctly prepare your tiller for use. It is recommended that you read this Section in its entirety before beginning assembly.

INSPECT UNIT

Inspect the unit and carton for damage immediately after delivery. Contact the carrier (trucking company) if you find or suspect damage. Inform them of the damage and request instructions for filing a claim. To protect your rights, put your claim in writing and mail a copy to the carrier within 15 days after the unit has been delivered. Contact us at the factory if you need assistance in this matter.

UNPACKING AND ASSEMBLY INSTRUCTIONS

STEP 1: UNPACKING INSTRUCTIONS

1.Remove any cardboard inserts and packaging material from the carton. Remove any staples from the bottom of the carton and remove the carton.

2.Cut the large, plastic tie strap that secures the transmission tube to the ship- ping pallet. Leave the handlebars on top of the tiller to avoid damaging any cables.

3. A bag with loose hardware is inside the literature envelope. Check the con- tents against the following list and Figure 2-1. Contact your local dealer or the factory if any items are missing or damaged.

NOTE: For electric start units, a second hardware bag is located near the battery.

4. The tiller is heavy. You should not attempt to remove it from the shipping platform until instructed to do so in these “Assembly” steps.

 

 

Screw (See Figure 2-1A)

5

2

3/8" Flat Washer

6

2

#10 Lockwasher

7

2

3/8"-16 Nylock Lock Nut

8

2

#10-32 x 1/2" Round Hd.

 

 

Screw

9

2

#10-32 Nut

10

1

Cotter Pin (not used)

11

4

Plastic Tie Strap (2 not used)

 

 

 

Tools/Materials Needed for Assembly

(1) 3/8" open-end wrench*

(1)7/16" open-end wrench* (electric start unit only)

(2)9/16" open-end wrench*

(1)7/8" open-end wrench or 8" long adjustable wrench

(1) Scissors (to trim plastic ties)

(1) Ruler

(1)Small board (to tap plastic knob on lever)

(1) Tire pressure gauge

(1) Clean oil funnel

(1)Clean, high-quality motor oil. Refer to the separate Engine Owner’s Manual for motor oil specifications and quantity required.

*Adjustable wrenches may be used.

IMPORTANT: Motor oil must be added to the engine crankcase before the engine is started. Follow the instructions in this “Assembly” Section and in the separate Engine Owner’s Manual.

NOTE: LEFT and RIGHT sides of the tiller are as viewed from the operator’s posi- tion behind the handlebars.

STEP 2: ATTACH HANDLEBARS

1.On electric start units, remove one screw and lockwasher from the curved

Figure 2-1: Loose hardware (shown in reduced size).

Flange

Figure 2-1A Handlebar height adjustment uses the flange head screw.

A

Figure 2-2: On electric start units, move height adjustment bracket aside.

height adjustment bracket (A, Figure 2-2), loosen the second screw, and swing the bracket to one side.

2.Cut the large, plastic cable ties that secure the handlebar ends to the handle- bar mounting tabs on the transmission top cover.

3.Gently lift handlebar (do not over- stretch attached cable) and place handle- bar cross-brace (B, Figure 2-3) in front of curved height adjustment bracket (C).

M

C

E

 

 

 

 

F

B

 

 

Figure 2-3: Forward clutch control cable not shown for clarity.

Image 6
Contents Operator’s Manual Engine Information Table of ContentsFinding Model Number Calling Customer SupportTraining SafetySafety Alert Symbol PreparationKeep children and pets away Maintenance and StorageSafety Use slower engine speedsDecals To Avoid Serious InjuryIntroduction AssemblyHardware BAG Parts List Inspect UnitAttach Reverse Clutch Control Cable Attach Forward Clutch Control CableAssistance Check AIR Pressure in Tires AssemblyAttach Wheel Gear Lever Marked NegForward Clutch Control Features and ControlsWheel Gear Lever To Operate the Forward Clutch ControlReverse Clutch Control Features and ControlsEngine Controls Depth RegulatorStarting and Stopping Engine PRE-START ChecklistOperation BREAK-IN OperationStarting the Engine Operating the TillerOperation Stopping the EngineFor reverse motion of the wheels and tines Stopping the Tiller and EngineTilling Tips & Techniques Choosing correct wheel and tine speedsTilling across slopes without using terraces Tilling up and down slopesTerrace Gardening Power Composting Loading and Unloading the TillerCheck Hardware MaintenanceMaintenance Schedule Check Tire PressureCheck for OIL Leaks MaintenanceTransmission Gear OIL Service To Check Transmission Gear Oil LevelAIR Cleaner Service Engine CleaningEngine OIL Service Spark Plug ServiceWheel Gear Cable Adjustment OFF Season StorageBolo Tines Checking and Adjusting Forward Clutch Belt Tension Cutting Edge TineChecking and Adjusting Reverse Clutch Belt Tension Checking Forward Belt TensionInstalling Forward Clutch Belt Removing Forward Clutch BeltReverse Clutch Belt Removal and Replacement Installing Reverse Clutch BeltRemoving Reverse Clutch Belt Battery Maintenance Troubleshooting Problem Possible Cause CorrectionBumper Model OEM-290-254 HILLER/FURROWER Model OEM-290-251ROW MARKER- Model OEM-290-257 TROY-BILT Tiller Lifetime Limited Warranty
Related manuals
Manual 40 pages 7.54 Kb Manual 36 pages 52.26 Kb Manual 25 pages 52.34 Kb

E666M, 665B, 664D specifications

Troy-Bilt is a trusted name in outdoor power equipment, and their line of tillers, including the E666M, 664D, and 665B models, exemplifies their commitment to quality and practicality. These tillers are designed to make soil preparation easier and more efficient, catering to both amateur gardeners and seasoned landscapers alike.

The Troy-Bilt E666M is a robust machine tailored for ease of use and reliability. With a powerful engine, it delivers consistent performance, ensuring that users can tackle even the toughest soils. One of its standout features is the adjustable tilling width, which provides flexibility for various gardening needs. This tiller also boasts a Reverse Tillage feature, allowing the operator to break up stubborn soil with ease while enhancing control during operation.

The 664D model takes efficiency a step further with its durable construction and user-friendly design. This tiller is equipped with a dependable engine that provides ample power for deep soil cultivation. The 664D features self-propulsion technology, allowing users to maintain steady speed without exerting excessive effort. The adjustable depth settings further enhance soil penetration, making it possible to cultivate deep for extensive planting or surface till for lighter gardening tasks.

With the 665B, Troy-Bilt introduces advanced engineering for increased maneuverability and performance. This tiller features a patented belt-drive system that improves torque and ensures optimal power transfer to the tines. The 665B is also designed with comfort in mind, featuring ergonomic handles that reduce strain on the operator, making it ideal for longer gardening sessions. Its heavy-duty tines ensure exceptional soil mixing, while the adjustable tilling width and depth allow for customization according to specific gardening requirements.

All three tillers come equipped with Troy-Bilt's signature red oversized drag stake, enabling users to control tilling depth and improve stability during operation. They are designed with durable components that promise longevity and reliability, ensuring that they can withstand rigorous use season after season.

In summary, the Troy-Bilt E666M, 664D, and 665B tillers offer a variety of features and technologies that cater to every gardening need. With their reliable engines, user-friendly designs, and advanced tilling capabilities, these models embody the innovation and durability that Troy-Bilt is known for, making them excellent choices for anyone looking to elevate their gardening experience.