Snapper EICFR5004B important safety instructions Tiller Tines, Belt Adjustment Replacement

Page 10

Section 3 - ADJUSTMENTS & REPAIR

3.3.2.ADD LUBRICATION TO CHAIN CASE: To add grease, remove the filler plug located just forward of the pulley shaft on the right hand side. See Figure 10. Add Snapper Part No. 2-9577 Benalene 900 grease (4 oz. Bottle) as needed to bring level up to bottom edge of the check plug opening. The total capacity of the case is about 48 ounces. DO NOT exceed this amount. Reinstall check plugs after checking. NOTE: Also available Snapper Part No. 2-9296 Benalene 900 grease (32 oz. Bottle).

CHAIN

CASE

MAIN CASE

RIGHTFILL PLUG HAND

WHEEL

FIGURE 10

3.4 TILLER TINES

Your Snapper Tiller has right hand and left hand tines. Replace both tines if blades become bent or are badly worn or otherwise damaged. Use correct Snapper replacement tines. The tines are secured to the tine shaft with a shear bolt, Part No. 2-8725 and Lock Nut Part No. 9-0222 on each side. NOTE: Two extra nuts and two bolts come with tiller. Keep spares on hand in case a bolt shears off or becomes lost while tilling. See Figure 11. DO NOT over tighten these shear bolts as this will cause premature failure. (Recommended torque is 5 to 8 foot pounds maximum). NOTE: Failure to use the correct shear bolts could result in serious damage to your Tiller. Use only the genuine Snapper replacement bolts and lock nuts specified above. These bolts are designed to shear at a specific stress to prevent damage. DO NOT use substitutes!

SHEAR BOLT (TORQUE TO 8 FT. LBS.)

LOCK NUT

TINE

ASSEMBLY

FIGURE 11

3.5BELT ADJUSTMENT - REPLACEMENT

STEP 1: BELT TENSION ADJUSTMENT: From the right side under the fuel tank, measure the length of the idler pulley spring at the end of the control cable in a relaxed position. Then move wheel and tine control bail up to the handle bar and measure the extended length of the spring. When properly adjusted, the spring will extend 1/4” to 1/2”. See Figure 12. To adjust, loosen and reposition the two jam nuts on the threaded end of cable located on the dash panel. Move jam nuts toward the end of threaded end of cable for more tension. Move jam nuts in a direction away from the end of threaded end of cable for less tension. See Figure 13. After adjustment, retighten both jam nuts against dash panel.

BELT

FIGURE 12

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents European Intermediate Rear Tine Tiller Series Model Number ExplanationProtection for Children Operational PrecautionsMaintenance and Storage PreparationTable of Contents Familiarization Control Identification & Safety Signs European PerformanceSnapper Manufacturers name of the product Wheel & Tine Control Tilling Procedure Handle BAR AdjustmentTransporting Standing the Tiller on END Service Parts & AssistanceTiller Lubrication Belt Adjustment Replacement Tiller TinesOFF Season Storage Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Service Notes Intermediate Rear Tine Tiller Series

EICFR5004B specifications

The Snapper EICFR5004B is a versatile and reliable riding lawn mower designed for homeowners who demand performance and efficiency in their lawn care routine. This mower is engineered to provide a smooth, clean cut while ensuring ease of use and comfort during operation.

One of the standout features of the Snapper EICFR5004B is its powerful engine. It is equipped with a robust 500cc Briggs & Stratton engine that delivers reliable starting and plenty of power for tackling tough grass and uneven terrain. The engine is designed for efficiency, allowing users to complete their mowing tasks quickly, even on larger lawns.

The cutting system of the EICFR5004B is another highlight. The mower boasts a 42-inch cutting deck that provides a wide cutting path, reducing the number of passes needed to achieve a pristine lawn. The deck is constructed from durable materials, ensuring longevity and resistance to wear and tear. Additionally, it features a six-position height adjustment lever, which allows users to easily customize cutting heights between 1.5 inches and 4 inches to suit their lawn’s specific needs.

Comfort is a key consideration in the design of the Snapper EICFR5004B. The mower features an ergonomic seat with ample cushioning, providing a comfortable riding experience over extended periods. The controls are intuitively placed and easy to reach, allowing users to operate the mower without strain. The compact design also makes it easy to maneuver in tight spaces, such as around flower beds and trees.

Another significant technology integrated into the Snapper EICFR5004B is its SmartSpeed control system. This innovative feature allows users to control their speed with precision. It provides three different speed ranges for trimming, towing, and mowing, making it versatile for various tasks. This means users can adjust their speed without compromising on cutting performance or efficiency.

Maintenance is simplified with the EICFR5004B as well. The mower is designed with a removable deck, making it easy to clean and service. The engine compartment is also accessible, allowing users to perform routine maintenance tasks without extensive effort.

In conclusion, the Snapper EICFR5004B is built for performance, comfort, and convenience. With its powerful engine, versatile cutting system, and innovative speed control technology, it is well-suited for homeowners seeking a reliable riding mower that effaces the complexities of lawn maintenance. Its combination of features makes mowing not only easier but also more enjoyable, setting a new standard in residential lawn care solutions.
Top Page Image Contents