Poulan FT825 Before Starting Engine, To Transport, Fill Engine with OIL See Fig, ADD Gasoline

Page 8

OPERATION

TO TRANSPORT

CAUTION: Beforeliftingortransporting, allow tiller engine and muffler to cool. Disconnect spark plug wire. Drain gasoline from fuel tank.

AROUND THE YARD

•Tip depth stake forward until it is held by the stake spring.

•Push tiller handles down, raising tines off the ground.

•Push or pull tiller to desired location.

AROUND TOWN

•Disconnect spark plug wire.

•Drain fuel tank.

•Transport in upright position to prevent oil leakage.

BEFORE STARTING ENGINE

IMPORTANT: BE VERY CAREFUL NOT TO ALLOW DIRT TO ENTER THE ENGINE WHEN CHECKING OR ADDING OIL OR FUEL. USE CLEAN OIL AND FUEL AND STORE IN APPROVED, CLEAN, COVERED CONTAINERS. USE CLEAN FILL FUNNELS.

FILL ENGINE WITH OIL (See Fig. 7)

•With engine level, remove engine oil filler plug.

•Fill engine with oil to point of overflowing. For approx- imate capacity see “PRODUCT SPECIFICATIONS” on page 3 of this manual.

•Tilt tiller back on its wheels and then re-level.

•With engine level, refill to point of overflowing if nec- essary. Replace oil filler plug.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

•To change engine oil, see the Maintenance section of this manual.

OIL

LEVEL

 

OIL

ine

FILLER

PLUG

4

 

t_

 

ar

 

_

 

eng

 

 

 

FIG. 7

 

ADD GASOLINE

• Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

8

CAUTION: Fill to within 1/2 inch of top of fuel tank to prevent spills and to allow for fuel expansion. If gasoline is ac- cidentally spilled, move machine away from area of spill. Avoid creating any source of ignition until gasoline vapors have disappeared.

Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 8)

CAUTION: Keep drive control bar in “DISENGAGED” position when start- ing engine.

When starting engine for the first time or if engine has run out of fuel, it will take extra pulls of the recoil starter to move fuel from the tank to the engine.

•Make sure spark plug wire is properly connected.

•Move shift lever indicator to “N” (neutral) position.

•Place throttle control in “FAST” position.

•Move choke control to choke position.

•Grasp recoil starter handle with one hand and grasp tiller handle with other hand. Pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point).

•Pull recoil starter handle quickly. Do not let starter handle snap back against starter.

•If engine fires but does not start, move choke control to half choke position. Pull recoil starter handle until engine starts.

•When engine starts, slowly move choke control to "RUN" position as engine warms up.

NOTE: A warm engine requires less choking to start.

•Move throttle control to desired running position.

•Allow engine to warm up for a few minutes before engaging tines.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents FT825 Operators Manual ModelSafety Rules Maintenance and StorageTraining PreparationTable of Contents Contents of Hardware Pack AssemblyTools Required for Assembly Unpack Carton & Install Handle See Fig Handle HeightTilling Width Tine OperationKnow Your Tiller Meets Ansi Safety RequirementsOperation HOW to USE Your Tiller Stopping See FigTine Operation See Fig TillingBefore Starting Engine To TransportFill Engine with OIL See Fig ADD GasolineCultivating Breaking in Your TillerTilling Hints General Recommendations MaintenanceMaintenance Schedule AIR Cleaner See Fig EngineCooling System See Fig To Change Engine OIL See FigsTiller Service and AdjustmentsCleaning Tine Operation Check See Fig To Remove Belt Guard See FigTo Replace V-BELTS See Figs Final Check OFF PositionTo Adjust Carburetor Belt ReplacementBelt Removal Check Tine OperationStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionLimited Warranty Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Dépannage DE Guide PasEntreposage Supplementaire InformationMoteur MotobineuseRéglages ET Révision Carburateur LE Régler Pour15 22 .FIG 21 .FIGFig la Voir Roiecour DE Protecteur LE Enlever Pour Fig la Voir Sesfrai DES L’UTILISATION DE Vérification Fraises DES Disposition 15 .FIGFig la Voir Guidon DU Hauteur LA Régler PourEntretien Nettoyage’ALLUMAGE Bougie SilencieuxLubrification MoteurFig la Voir AIR À Filtre Générales Recommandations Lubrification DE Tableau’ENTRETIEN Calendrier LubrificationUtilisation Labourage DE ConseilsMotobineuse LA DE Rodage CultureMoteur LE Démarrer DE Avant Moteur LE Démarrer Pour’ESSENCE Réservoir LE Remplir ’HUILE Moteur LE RemplirBineuse Moto Votre Utiliser CommentLabourage Fig la FRAISESVoir DES UtilisationMotobineuse Votre Connaissez Motobineuse VotreMoteur le démarrer de permet Démarrage DE Poignée Manuel ce ConservezManche LE Installer ET Déballer MontageGeraboula DU Largeur Dents DES UtilisationPièces DES SAC DU Contenu Fig la Voir D’OPERATEUR PositionMontage LE Pour Exiges Outils LES De Clés 2 Pince 1 Tournevis 1 usage tout à CouteauSommaire Produit DU SpécificationsClient DU Responsabilités Réglages ET Révision Client DU ResponsabilitésSécurité DE Règles Entreposage ET EntretienMotobineuses des Sécurité toute En lUtilisation pour ConseilsAvertissement OpérateurDU Manuel

FT825 specifications

The Poulan FT825 is a robust and reliable tiller designed for homeowners and gardening enthusiasts who require a powerful tool for soil preparation. With a focus on durability and ease of use, the FT825 is engineered to make tilling tasks simpler and more efficient.

One of the main features of the Poulan FT825 is its 208cc four-stroke engine. This powerful engine delivers ample torque and performance, allowing for efficient tilling in various soil types. The four-stroke design ensures that the engine runs smoothly while maintaining lower emissions, making it an environmentally friendly choice.

The tiller features a durable steel frame that provides stability and support during operation. The frame is designed to withstand the rigors of heavy use, ensuring longevity and reliability over the years. Additionally, the FT825 comes with adjustable tilling width and depth settings, allowing users to customize their tilling experience based on specific gardening needs. The tilling width can be adjusted from 11 inches to 22 inches, making it versatile for different tasks.

Equipped with a set of rugged, spiral-tined tines, the FT825 can penetrate hard soil effortlessly, breaking up compacted earth for easier planting. These heavy-duty tines are designed to withstand tough conditions while providing exceptional soil mixing capabilities.

The Poulan FT825 also features ergonomic handles that are adjustable for user comfort. This design minimizes strain while tilling, enabling longer operation without discomfort. The integrated anti-vibration system further enhances user comfort by reducing the vibrations transmitted to the operator's hands.

Another notable technology is the easy-start system, which ensures that the engine starts with minimal effort. This is particularly beneficial for novice users who may struggle with traditional pull-start mechanisms.

For transport and storage, the FT825 is designed with foldable handlebars, which reduces its footprint and makes it easier to maneuver in tight spaces. This feature also simplifies the storage process, ensuring that the tiller can be conveniently stored when not in use.

In summary, the Poulan FT825 is a feature-rich tiller that combines power, durability, and user-friendly designs. With its robust engine, adjustable settings, and thoughtful technologies, it is an ideal choice for anyone looking to cultivate their garden effectively.
Top Page Image Contents