Troy-Bilt E686N manual Operator’s Manual

Page 1

Operator’s Manual

Rear-tine PTO Tiller Models

682J—HorseTME686N—HorseTME682L—HorseTM

Model 682J Shown

IMPORTANT:READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush- covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available by contacting the service department at Troy-Bilt LLC, P.O. Box 361131 Cleveland, Ohio 44136-0019.

TROY-BILT LLC, P.O. BOX 361131, CLEVELAND, OH 44136-0019

PRINTED IN USA

FORM NO. 770-10598C

 

(9/2003)

Image 1
Contents Operator’s Manual Table of Contents Safety Alert Symbol SafetyKeep children and pets away SafetyUse slower wheel, tine and engine speeds Operating Symbols Maintenance and StorageIntroduction Tools/Materials Needed for AssemblyInspect Unit Attach HandlebarMove Tiller Off Shipping Platform AssemblyRemove the temporary screw J, Figure Check Gear Oil LevelsAttach Engine Throttle Lever and Cable Adjust Air Pressure in TiresAdd Motor Oil to Engine Oil Level HoleConnect the Wire Harness Receptacle Install Battery CablesTo Avoid Personal Injury or Property Damage Never bring a gas can near the positiveWheels/Tines/PTO Drive Lever PTO Attachments FeatureForward Interlock Levers EngineHandlebar Height Adjustment Lever Features and ControlsWheel Speed Lever Tines/PTO Clutch LeverEngine Controls Engine Throttle Lever Keyswitch StarterMove the engine Throttle lever to Stop position Pre-Start Checklist Following steps describe how to start and stop the engineBreak-In Operation Starting and Stopping the EngineMove engine throttle lever -2 away from Stop OperationOperating the Tiller Cold Weather OperationStopping the Engine and Tiller Moving the Tiller Forward and TillingStopping Reverse Motion Moving the Tiller in ReverseTo Stop the Engine Making TurnsHow to Check the Interlock System Testing the Forward Interlock Safety SystemLoading and Unloading the Tiller Transporting The Tiller Around Your PropertyLoading the Tiller Changing Speed BeltsUnloading the Tiller Changing Belt From LOW Range to High RangeChanging Belt From High Range to LOW Range Choosing Wheel Tine SpeedsMove the Wheels/Tines/PTO Drive Lever into Neutral Go to right side of tiller and finish seating the beltTilling depths Let the tiller do the workAvoid tilling wet, soggy soil To help avoid personal injury, be awareSuggested tilling patterns Avoid making footprintsTilling on slopes Tilling up and down slopesTerrace Gardening Clearing the tinesTilling Under Corn Wide-Row PlantingSoil Enrichment Idea Removing Tine Attachment Removing And Replacing The Tine AttachmentMove the tiller to level ground Place Wheel Speed Lever into Free Wheel FigureSetting Up Stationary Attachments Installing the Tine AttachmentGuide Pin Mounting Hole Move the two swing-bolts intoStarting The Engine Setting Up Non-Powered Attach- mentsOperating Stationary Attachments Stopping the EngineHours EveryTighten Bolts and Nuts MaintenanceTiller Lubrication Checking the Power Unit Oil Level Transmission Gear Oil MaintenanceChecking for Oil Leaks Checking Gear Oil LevelsChecking the Tine Attachment Oil Level Adding or Changing Gear OilFor Dipsticks With Hot/Cold Markings If the level is incorrect, see Adding or Changing Gear OilDraining and Filling PTO Power Unit Transmission Adding Gear Oil to PTO Power Unit TransmissionAdding Gear Oil to the Tine Attachment Transmission Draining and Filling the Tine Attachment TransmissionMeasuring and Adjusting Drive Belt Tension Drive Belt MaintenanceHow to Measure Belt Tension Belt Adjustment ToolRemoving the Belt Replacing the Drive BeltReplacing the Drive Belt Reverse Disc Inspection Reverse Drive System MaintenanceInstalling a New Reverse Disc Checking and Adjusting Reverse the Drive SystemChecking and Adjusting Reverse Disc Replacing the Reverse DiscAdjusting Reverse Drive Bolo Tine MaintenanceChecking Tines for Wear Removing and Replacing a Tine Holder Assembly Single Tine ReplacementRemoving Tine Holder Assembly Replacing Tines Holder AssemblyTire and Wheel Maintenance Tine Shaft MaintenanceAir Cleaner Maintenance Spark Plug MaintenanceTesting the Forward Interlock Wiring System Inspecting Forward Interlock Wiring SystemStoring Your Tiller Troubleshooting Procedures Appendix a TroubleshootingLinkage EccentricTiller Pulls To One Side 290-258-081 290-257-081 Row Marker AttachmentDozer/Snow Blade Attachment Wrap-Around Bumper GuardPage TROY-BILT Tiller Lifetime Limited Warranty
Related manuals
Manual 44 pages 31.64 Kb Manual 43 pages 63.89 Kb