Troy-Bilt E686N, 682J, E682L manual Operator’s Manual

Page 1

Operator’s Manual

Rear-tine PTO Tiller Models

682J—HorseTME686N—HorseTME682L—HorseTM

Model 682J Shown

IMPORTANT:READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush- covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available by contacting the service department at Troy-Bilt LLC, P.O. Box 361131 Cleveland, Ohio 44136-0019.

TROY-BILT LLC, P.O. BOX 361131, CLEVELAND, OH 44136-0019

PRINTED IN USA	FORM NO. 770-10598D
	(10/15/2004)

Image 1

Contents Operator’s Manual Table of Contents Safety Alert Symbol SafetyKeep children and pets away SafetyUse slower wheel, tine and engine speeds Operating Symbols Maintenance and StorageIntroduction Tools/Materials Needed for AssemblyInspect Unit Attach HandlebarMove Tiller Off Shipping Platform AssemblyRemove the temporary screw J, Figure Check Gear Oil LevelsAttach Engine Throttle Lever and Cable Adjust Air Pressure in TiresAdd Motor Oil to Engine Oil Level HoleConnect the Wire Harness Receptacle Install Battery CablesTo Avoid Personal Injury or Property Damage Never bring a gas can near the positiveWheels/Tines/PTO Drive Lever PTO Attachments FeatureForward Interlock Levers EngineHandlebar Height Adjustment Lever Features and ControlsWheel Speed Lever Tines/PTO Clutch LeverEngine Controls Engine Throttle Lever Keyswitch StarterMove the engine Throttle lever to Stop position Pre-Start Checklist Following steps describe how to start and stop the engineBreak-In Operation Starting and Stopping the EngineMove engine throttle lever -2 away from Stop OperationOperating the Tiller Cold Weather OperationStopping the Engine and Tiller Moving the Tiller Forward and TillingStopping Reverse Motion Moving the Tiller in ReverseTo Stop the Engine Making TurnsHow to Check the Interlock System Testing the Forward Interlock Safety SystemLoading and Unloading the Tiller Transporting The Tiller Around Your PropertyLoading the Tiller Changing Speed BeltsUnloading the Tiller Changing Belt From LOW Range to High RangeChanging Belt From High Range to LOW Range Choosing Wheel Tine SpeedsMove the Wheels/Tines/PTO Drive Lever into Neutral Go to right side of tiller and finish seating the beltTilling depths Let the tiller do the workAvoid tilling wet, soggy soil To help avoid personal injury, be awareSuggested tilling patterns Avoid making footprintsTilling on slopes Tilling up and down slopesTerrace Gardening Clearing the tinesTilling Under Corn Wide-Row PlantingSoil Enrichment Idea Removing Tine Attachment Removing And Replacing The Tine AttachmentMove the tiller to level ground Place Wheel Speed Lever into Free Wheel FigureSetting Up Stationary Attachments Installing the Tine AttachmentGuide Pin Mounting Hole Move the two swing-bolts intoStarting The Engine Setting Up Non-Powered Attach- mentsOperating Stationary Attachments Stopping the EngineHours EveryTighten Bolts and Nuts MaintenanceTiller Lubrication Checking the Power Unit Oil Level Transmission Gear Oil MaintenanceChecking for Oil Leaks Checking Gear Oil LevelsChecking the Tine Attachment Oil Level Adding or Changing Gear OilFor Dipsticks With Hot/Cold Markings If the level is incorrect, see Adding or Changing Gear OilDraining and Filling PTO Power Unit Transmission Adding Gear Oil to PTO Power Unit TransmissionAdding Gear Oil to the Tine Attachment Transmission Draining and Filling the Tine Attachment TransmissionMeasuring and Adjusting Drive Belt Tension Drive Belt MaintenanceHow to Measure Belt Tension Belt Adjustment ToolRemoving the Belt Replacing the Drive BeltReplacing the Drive Belt Reverse Disc Inspection Reverse Drive System MaintenanceInstalling a New Reverse Disc Checking and Adjusting Reverse the Drive SystemChecking and Adjusting Reverse Disc Replacing the Reverse DiscAdjusting Reverse Drive Bolo Tine MaintenanceChecking Tines for Wear Removing and Replacing a Tine Holder Assembly Single Tine ReplacementRemoving Tine Holder Assembly Replacing Tines Holder AssemblyTire and Wheel Maintenance Tine Shaft MaintenanceAir Cleaner Maintenance Spark Plug MaintenanceTesting the Forward Interlock Wiring System Inspecting Forward Interlock Wiring SystemStoring Your Tiller Troubleshooting Procedures Appendix a TroubleshootingLinkage EccentricTiller Pulls To One Side 290-258-081 290-257-081 Row Marker AttachmentDozer/Snow Blade Attachment Wrap-Around Bumper Guard

Related manuals

Manual 19 pages 49.32 Kb

Manual 44 pages 31.64 Kb

Manual 45 pages 50.13 Kb

E682L, E686N, 682J specifications

The Troy-Bilt E682L and E682J are two powerful and efficient snow throwers designed for residential use, enabling homeowners to tackle winter's toughest snow challenges with ease. Both models are part of Troy-Bilt's commitment to creating durable equipment that simplifies outdoor maintenance.

One of the main features of the Troy-Bilt E682L and E682J is their robust engine. Equipped with a reliable 243cc OHV (Overhead Valve) engine, these snow throwers provide robust power, ensuring that users can clear snow quickly and effectively. The engines are designed for easy starting, even in cold conditions, so you won’t have to worry about fumbling with difficult pull cords when snowy weather strikes.

Another significant characteristic of these models is their 24-inch clearing width combined with a 21-inch intake height. This allows for efficient snow removal, enabling users to clear driveways and sidewalks with fewer passes. The heavy-duty auger system is engineered to cut through packed snow with ease, ensuring that even the toughest winter weather conditions don’t stand a chance.

Both the E682L and E682J feature a 180-degree adjustable chute that directs the snow where it needs to go. This puts control in the hands of the user, preventing snow from being thrown back onto the paths that have already been cleared. The quick-release chute deflector allows for easy height adjustments, giving users the flexibility to adapt to different snow conditions.

These models are also designed with user comfort in mind. The Troy-Bilt E682L and E682J come with heated hand grips, which make operating the snow thrower more pleasant during long periods in cold weather. The ergonomic handles provide a comfortable grip, and the adjustable handle height ensures that users of various sizes can operate the machine comfortably.

Additionally, both models feature large, rugged tires that provide enhanced traction on various surfaces, whether it’s icy pavement or a snow-covered driveway. This design consideration contributes to their overall stability and maneuverability, allowing users to navigate through challenging winter conditions with confidence.

In summary, the Troy-Bilt E682L and E682J snow throwers are powerful, user-friendly machines equipped with essential features that make snow removal efficient and manageable. With their reliable engines, robust clearing capabilities, adjustable chutes, and comfortable handling, these models are valuable tools for any homeowner looking to stay ahead of winter weather.