Troy-Bilt 682J, E686N, E682L manual Safety Alert Symbol

Page 3

Section

1Safety

Safety Alert Symbol

This is a safety alert symbol. It is used in this manual and on the unit to alert you to

potential hazards. When you see this symbol, read and obey the message that follows it.

Failure to obey safety messages could result in personal injury or property damage.

This machine meets voluntary safety standard B71.8

–1996, which is sponsored by the Outdoor Power Equipment Institute, Inc., and is published by the American National Standards Institute.

WARNING

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

Training

1.Carefully read this Owner’s Manual, the separate Engine Owner’s Manual, and any other literature you may receive. Be thor- oughly familiar with the controls and the proper use of the tiller and its engine. Know how to stop the unit and disengage the controls quickly.

2.Never allow children to operate the tiller. Never allow adults to operate the tiller without proper instruction.

3. Keep the area of operation clear of all persons, particularly children and pets.

4.Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people, their property, and themselves.

Preparation

1.Thoroughly inspect the area where the tiller is to be used and remove all foreign objects.

2.Put the Wheels/Tines/PTO Drive Lever into NEUTRAL before starting the engine.

3.Do not operate the tiller without wearing adequate outer garments. Avoid loose garments or jewelry that could get caught in moving parts.

4.Do not operate the tiller when barefoot or wearing sandals, sneakers, or light footwear. Wear protective footwear that will improve footing on slippery surfaces.

5.Do not till near underground electric cables, telephone lines, pipes or hoses. If in doubt, contact your telephone or utility company.

6.Warning: Handle fuel with care; it is highly flammable and its vapors are explosive. Be sure to take the following precautions:

a. Store fuel in containers specifically designed for this purpose.

b. The gas cap shall never be removed or fuel added while the engine is running. Allow the engine to cool for several minutes before adding fuel.

c. Keep matches, cigarettes, cigars, pipes, open flames, and sparks away from the fuel tank and fuel container.

d. Fill fuel tank outdoors with extreme

care. Never fill fuel tank indoors. Use a funnel or spout to prevent spillage.

e. Replace all fuel tank and container caps securely.

f.If fuel is spilled, do not attempt to start the engine, but move the machine away from the area of spillage and avoid creating any source of ignition until fuel vapors have dissipated.

7.Never make adjustments when engine is running (unless recommended by manufacturer).

Operation

1.Do not put hands or feet near or under rotating parts. Do not allow hands or any other part of the body or clothing near the rotating tines or near any other moving part. The tines begin to rotate forward

once the engine starts, the Tines/PTO Clutch Lever is in the ENGAGE position, the Forward Interlock Levers are squeezed closed and the Wheels/Tines/PTO Drive Lever is shifted to FORWARD. The tines rotate in Reverse whether the Interlock Levers are closed or open.

2.Exercise extreme caution when on or crossing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic. Do not carry passengers.

3. After striking a foreign object, stop the engine, remove the wire from the spark plug wire and prevent it from touching the spark plug. Thoroughly inspect the machine for any damage and repair the damage before restarting and operating the machine.

4. Exercise caution to avoid slipping or falling.

5. If the unit should start to vibrate abnor- mally, stop the engine, disconnect the spark plug wire and prevent it from touching the spark plug, and check imme- diately for the cause. Vibration is generally a warning of trouble.

6. Stop the engine, disconnect the spark plug wire and prevent it from touching the spark plug whenever you leave the operating position, before unclogging the tines, or when making any repairs, adjust- ments or inspections.

7.Take all possible precautions when leaving machine unattended. Stop engine. Disconnect spark plug wire and move it away from spark plug. Remove ignition key on electric start models

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Operator’s Manual Table of Contents Safety Alert Symbol SafetySafety Keep children and pets awayUse slower wheel, tine and engine speeds Operating Symbols Maintenance and StorageAttach Handlebar Tools/Materials Needed for AssemblyIntroduction Inspect UnitMove Tiller Off Shipping Platform AssemblyRemove the temporary screw J, Figure Check Gear Oil LevelsOil Level Hole Adjust Air Pressure in TiresAttach Engine Throttle Lever and Cable Add Motor Oil to EngineNever bring a gas can near the positive Install Battery CablesConnect the Wire Harness Receptacle To Avoid Personal Injury or Property DamageEngine PTO Attachments FeatureWheels/Tines/PTO Drive Lever Forward Interlock LeversTines/PTO Clutch Lever Features and ControlsHandlebar Height Adjustment Lever Wheel Speed LeverKeyswitch Starter Engine Controls Engine Throttle LeverMove the engine Throttle lever to Stop position Starting and Stopping the Engine Following steps describe how to start and stop the enginePre-Start Checklist Break-In OperationMove engine throttle lever -2 away from Stop OperationMoving the Tiller Forward and Tilling Cold Weather OperationOperating the Tiller Stopping the Engine and TillerMaking Turns Moving the Tiller in ReverseStopping Reverse Motion To Stop the EngineTransporting The Tiller Around Your Property Testing the Forward Interlock Safety SystemHow to Check the Interlock System Loading and Unloading the TillerChanging Belt From LOW Range to High Range Changing Speed BeltsLoading the Tiller Unloading the TillerGo to right side of tiller and finish seating the belt Choosing Wheel Tine SpeedsChanging Belt From High Range to LOW Range Move the Wheels/Tines/PTO Drive Lever into NeutralTo help avoid personal injury, be aware Let the tiller do the workTilling depths Avoid tilling wet, soggy soilTilling up and down slopes Avoid making footprintsSuggested tilling patterns Tilling on slopesTerrace Gardening Clearing the tinesWide-Row Planting Tilling Under CornSoil Enrichment Idea Place Wheel Speed Lever into Free Wheel Figure Removing And Replacing The Tine AttachmentRemoving Tine Attachment Move the tiller to level groundMove the two swing-bolts into Installing the Tine AttachmentSetting Up Stationary Attachments Guide Pin Mounting HoleStopping the Engine Setting Up Non-Powered Attach- mentsStarting The Engine Operating Stationary AttachmentsHours EveryMaintenance Tighten Bolts and NutsTiller Lubrication Checking Gear Oil Levels Transmission Gear Oil MaintenanceChecking the Power Unit Oil Level Checking for Oil LeaksIf the level is incorrect, see Adding or Changing Gear Oil Adding or Changing Gear OilChecking the Tine Attachment Oil Level For Dipsticks With Hot/Cold MarkingsDraining and Filling the Tine Attachment Transmission Adding Gear Oil to PTO Power Unit TransmissionDraining and Filling PTO Power Unit Transmission Adding Gear Oil to the Tine Attachment TransmissionBelt Adjustment Tool Drive Belt MaintenanceMeasuring and Adjusting Drive Belt Tension How to Measure Belt TensionReplacing the Drive Belt Removing the BeltReplacing the Drive Belt Reverse Disc Inspection Reverse Drive System MaintenanceReplacing the Reverse Disc Checking and Adjusting Reverse the Drive SystemInstalling a New Reverse Disc Checking and Adjusting Reverse DiscBolo Tine Maintenance Adjusting Reverse DriveChecking Tines for Wear Replacing Tines Holder Assembly Single Tine ReplacementRemoving and Replacing a Tine Holder Assembly Removing Tine Holder AssemblySpark Plug Maintenance Tine Shaft MaintenanceTire and Wheel Maintenance Air Cleaner MaintenanceInspecting Forward Interlock Wiring System Testing the Forward Interlock Wiring SystemStoring Your Tiller Eccentric Appendix a TroubleshootingTroubleshooting Procedures LinkageTiller Pulls To One Side Wrap-Around Bumper Guard Row Marker Attachment290-258-081 290-257-081 Dozer/Snow Blade Attachment
Related manuals
Manual 19 pages 49.32 Kb Manual 44 pages 31.64 Kb Manual 45 pages 50.13 Kb

E682L, E686N, 682J specifications

The Troy-Bilt E682L and E682J are two powerful and efficient snow throwers designed for residential use, enabling homeowners to tackle winter's toughest snow challenges with ease. Both models are part of Troy-Bilt's commitment to creating durable equipment that simplifies outdoor maintenance.

One of the main features of the Troy-Bilt E682L and E682J is their robust engine. Equipped with a reliable 243cc OHV (Overhead Valve) engine, these snow throwers provide robust power, ensuring that users can clear snow quickly and effectively. The engines are designed for easy starting, even in cold conditions, so you won’t have to worry about fumbling with difficult pull cords when snowy weather strikes.

Another significant characteristic of these models is their 24-inch clearing width combined with a 21-inch intake height. This allows for efficient snow removal, enabling users to clear driveways and sidewalks with fewer passes. The heavy-duty auger system is engineered to cut through packed snow with ease, ensuring that even the toughest winter weather conditions don’t stand a chance.

Both the E682L and E682J feature a 180-degree adjustable chute that directs the snow where it needs to go. This puts control in the hands of the user, preventing snow from being thrown back onto the paths that have already been cleared. The quick-release chute deflector allows for easy height adjustments, giving users the flexibility to adapt to different snow conditions.

These models are also designed with user comfort in mind. The Troy-Bilt E682L and E682J come with heated hand grips, which make operating the snow thrower more pleasant during long periods in cold weather. The ergonomic handles provide a comfortable grip, and the adjustable handle height ensures that users of various sizes can operate the machine comfortably.

Additionally, both models feature large, rugged tires that provide enhanced traction on various surfaces, whether it’s icy pavement or a snow-covered driveway. This design consideration contributes to their overall stability and maneuverability, allowing users to navigate through challenging winter conditions with confidence.

In summary, the Troy-Bilt E682L and E682J snow throwers are powerful, user-friendly machines equipped with essential features that make snow removal efficient and manageable. With their reliable engines, robust clearing capabilities, adjustable chutes, and comfortable handling, these models are valuable tools for any homeowner looking to stay ahead of winter weather.
Top Page Image Contents