Poulan 413288 Tine Operation Check See Fig, To Remove Belt Guard See Fig, Final Check on Position

Page 13

SERVICE AND ADJUSTMENTS

NARROW TILLING/CULTIVATING - 12-3/4" PATH (See Fig. 18)

•Remove outer tines.

tine_6

INNER TINES ONLY

FIG. 18

NOTE: When reassembling outer tines, be sure right tine assembly (marked “R”) and left tine assembly (marked “L”) are mounted to correct side of tine shaft.

TINE OPERATION CHECK (See Fig. 19)

WARNING: Disconnect spark plug wire from spark plug to prevent starting while checking tine operation.

For proper tine operation, forward tine control lever must be against control body and all slack removed from inner wire of control cable when control is in the “OFF” (up) position.

If lever and cable are loose, loosen cable clip at lower end of cable. Pull up on cable to remove slack, without extending spring on end of cable, and retighten cable clip.

FINAL CHECK “OFF” POSITION

•With tine control “OFF” (up), push down on handle to raise tines off the ground.

•Slowly pull recoil starter handle while observing tines. Tines should not rotate.

•If tines rotate, inner wire of control cable is too tight which is extending lower spring and engaging tines. Loosen cable clip and push down on cable only enough to relieve spring tension. Tighten cable clip.

•Recheck in “OFF” position and adjust if necessary.

FINAL CHECK “ON” POSITION

•With tine control “ON” (held down to handle) push down on handle to raise tines off the ground.

•Slowly pull recoil starter handle while observing tines. Tines should rotate forward.

•If tines do not rotate, inner wire of control cable is too loose. Loosen cable clip and pull cable up to remove slack and retighten clip.

•Recheck in “ON” position and adjust if necessary. NOTE: If “ON” position check required adjustment, recheck “OFF” position adjustment to insure tines do not rotate when control is “OFF” (up).

 

 

 

 

 

FORWARD TINE

 

 

 

 

 

CONTROL IN “OFF”

 

 

 

 

 

(UP) POSITION

 

 

 

 

 

TINE CONTROL

 

 

 

 

BODY

“ON” POSITION

 

 

 

 

 

 

 

_

9

4

 

 

 

 

 

 

 

 

 

 

 

and

l

 

 

 

h

 

 

 

 

 

 

 

 

CABLE

TINE

 

 

 

 

CLIP

 

 

 

 

 

CONTROL

 

 

 

 

 

CABLE

 

 

 

 

FIG. 19

 

TO REMOVE BELT GUARD (See Fig. 20)

•Remove two (2) cap nuts and washers from side of belt guard.

•Loosen (do not remove) tine shield nut on underside of tine shield.

•Pull belt guard out and away from unit.

•Replace belt guard by reversing above procedure. Be sure slot in bottom of belt guard is under head of tine shield bolt and all nuts are tightened securely.

CAP NUTS

AND WASHERS

BELT

GUARD

TINE

SHIELD

NUT

FIG. 20

TO REPLACE V-BELTS (See Figs. 21 and 22)

Replace V-belts if they have stretched considerably or if they show cracks or frayed edges. There are two (2) V-belts - forward (inside) and reverse (outside).

Belt guard must be removed to service belts. See “TO REMOVE BELT GUARD” in this section of manual.

NOTE: Observe carefully routing of both belts and location of all belt guides before removing belts.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Operators Manual Model FT825Maintenance and Storage Safety RulesTraining PreparationTable of Contents Tools Required for Assembly AssemblyContents of Hardware Pack Handle Height Unpack Carton & Install Handle See FigTilling Width Tine OperationOperation Meets Ansi Safety RequirementsKnow Your Tiller Stopping See Fig HOW to USE Your TillerTine Operation See Fig TillingTo Transport Before Starting EngineFill Engine with OIL See Fig ADD GasolineTilling Hints Breaking in Your TillerCultivating Maintenance Schedule MaintenanceGeneral Recommendations Engine AIR Cleaner See FigCooling System See Fig To Change Engine OIL See FigsCleaning Service and AdjustmentsTiller To Remove Belt Guard See Fig Tine Operation Check See FigTo Replace V-BELTS See Figs Final Check OFF PositionBelt Replacement To Adjust CarburetorBelt Removal Check Tine OperationOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsLimited Warranty Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Pas Dépannage DE GuideSupplementaire Information EntreposageMoteur MotobineuseCarburateur LE Régler Pour Réglages ET Révision15 22 .FIG 21 .FIGFig la Voir Roiecour DE Protecteur LE Enlever Pour Fraises DES Disposition 15 .FIG Fig la Voir Sesfrai DES L’UTILISATION DE VérificationFig la Voir Guidon DU Hauteur LA Régler PourNettoyage Entretien’ALLUMAGE Bougie SilencieuxFig la Voir AIR À Filtre MoteurLubrification Lubrification DE Tableau Générales Recommandations’ENTRETIEN Calendrier LubrificationLabourage DE Conseils UtilisationMotobineuse LA DE Rodage CultureMoteur LE Démarrer Pour Moteur LE Démarrer DE Avant’ESSENCE Réservoir LE Remplir ’HUILE Moteur LE RemplirMoto Votre Utiliser Comment BineuseLabourage Fig la FRAISESVoir DES UtilisationMotobineuse Votre Motobineuse Votre ConnaissezMoteur le démarrer de permet Démarrage DE Poignée Manuel ce ConservezMontage Manche LE Installer ET DéballerGeraboula DU Largeur Dents DES UtilisationFig la Voir D’OPERATEUR Position Pièces DES SAC DU ContenuMontage LE Pour Exiges Outils LES De Clés 2 Pince 1 Tournevis 1 usage tout à CouteauProduit DU Spécifications SommaireClient DU Responsabilités Réglages ET Révision Client DU ResponsabilitésEntreposage ET Entretien Sécurité DE RèglesMotobineuses des Sécurité toute En lUtilisation pour ConseilsDU Manuel OpérateurAvertissement

413288 specifications

The Poulan 413288 is a remarkable chainsaw that has gained reputation among both casual users and professional loggers for its powerful performance and user-friendly design. With an emphasis on high efficiency and reliability, this chainsaw is perfect for a variety of cutting tasks, from trimming branches to felling small trees.

One of the standout features of the Poulan 413288 is its robust engine. It is equipped with a potent two-stroke engine that provides ample power for tackling tough jobs. The engine not only offers impressive performance but is also designed for fuel efficiency, allowing users to work longer without the need for constant refueling. This makes it a practical choice for both hobbyists and professionals who require sustained power during extended cutting sessions.

The chainsaw boasts a 16-inch cutting bar, which strikes an ideal balance between maneuverability and cutting capacity. This length is suitable for handling a wide array of cutting tasks, enabling users to make precise cuts with ease. The chain is designed for smooth operation, ensuring that the saw glides through wood effortlessly.

Another key feature of the Poulan 413288 is its lightweight design. Weighing in at just under 10 pounds, this chainsaw is easy to handle, reducing user fatigue during longer work periods. The ergonomic handle adds to the overall comfort, providing a secure grip that enhances control during operation.

Safety is also a priority in the design of the Poulan 413288. It includes a chain brake that activates in the event of a kickback, preventing accidents and ensuring user safety. Additionally, the chainsaw features an automatic oiling system that keeps the chain lubricated and reduces wear, further promoting durability.

The Poulan 413288 incorporates innovative technologies such as the Easy Start feature, which minimizes the effort required to start the engine. This is especially beneficial for users who may not have extensive experience with chainsaws.

In summary, the Poulan 413288 combines power, efficiency, and safety in one compact package. With its advanced features, user-friendly design, and reliable performance, it stands out as a versatile tool for anyone in need of a dependable chainsaw. Whether you're a seasoned professional or a weekend warrior, the Poulan 413288 is designed to meet your cutting needs with ease and precision.
Top Page Image Contents