Poulan 413288 manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 15

STORAGE

Immediately prepare your tiller for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the tiller with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TILLER

•Clean entire tiller (See “CLEANING” in the Maintenance section of this manual).

•Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

•Lubricate as shown in the Maintenance section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS THE CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent.

•Use fresh fuel next season.

NOTE: Fuel stablizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stablizer container. Run engine at least 10 minutes after adding stablizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

•Remove spark plug.

•Pour 1 ounce (29 ml) of oil through spark plug hole into cylinder.

•Pull starter handle slowly several times to distribute oil.

•Replace with new spark plug.

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your unit indoors and cover it to give protection from dust and dirt.

•Cover your unit with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your unit to rust.

IMPORTANT: NEVER COVER TILLER WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Operators Manual Model FT825Preparation Safety RulesMaintenance and Storage TrainingTable of Contents Assembly Tools Required for AssemblyContents of Hardware Pack Tine Operation Unpack Carton & Install Handle See FigHandle Height Tilling WidthMeets Ansi Safety Requirements OperationKnow Your Tiller Tilling HOW to USE Your TillerStopping See Fig Tine Operation See FigADD Gasoline Before Starting EngineTo Transport Fill Engine with OIL See FigBreaking in Your Tiller Tilling HintsCultivating Maintenance Maintenance ScheduleGeneral Recommendations To Change Engine OIL See Figs AIR Cleaner See FigEngine Cooling System See FigService and Adjustments CleaningTiller Final Check OFF Position Tine Operation Check See FigTo Remove Belt Guard See Fig To Replace V-BELTS See FigsCheck Tine Operation To Adjust CarburetorBelt Replacement Belt RemovalEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsLimited Warranty Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Pas Dépannage DE GuideMotobineuse EntreposageSupplementaire Information Moteur21 .FIG Réglages ET RévisionCarburateur LE Régler Pour 15 22 .FIGFig la Voir Roiecour DE Protecteur LE Enlever Pour Guidon DU Hauteur LA Régler Pour Fig la Voir Sesfrai DES L’UTILISATION DE VérificationFraises DES Disposition 15 .FIG Fig la VoirSilencieux EntretienNettoyage ’ALLUMAGE BougieMoteur Fig la Voir AIR À FiltreLubrification Lubrification Générales RecommandationsLubrification DE Tableau ’ENTRETIEN CalendrierCulture UtilisationLabourage DE Conseils Motobineuse LA DE Rodage’HUILE Moteur LE Remplir Moteur LE Démarrer DE AvantMoteur LE Démarrer Pour ’ESSENCE Réservoir LE RemplirFig la FRAISESVoir DES Utilisation BineuseMoto Votre Utiliser Comment LabourageManuel ce Conservez Motobineuse Votre ConnaissezMotobineuse Votre Moteur le démarrer de permet Démarrage DE PoignéeDents DES Utilisation Manche LE Installer ET DéballerMontage Geraboula DU LargeurDe Clés 2 Pince 1 Tournevis 1 usage tout à Couteau Pièces DES SAC DU ContenuFig la Voir D’OPERATEUR Position Montage LE Pour Exiges Outils LESRéglages ET Révision Client DU Responsabilités SommaireProduit DU Spécifications Client DU ResponsabilitésEn lUtilisation pour Conseils Sécurité DE RèglesEntreposage ET Entretien Motobineuses des Sécurité touteOpérateur DU ManuelAvertissement

413288 specifications

The Poulan 413288 is a remarkable chainsaw that has gained reputation among both casual users and professional loggers for its powerful performance and user-friendly design. With an emphasis on high efficiency and reliability, this chainsaw is perfect for a variety of cutting tasks, from trimming branches to felling small trees.

One of the standout features of the Poulan 413288 is its robust engine. It is equipped with a potent two-stroke engine that provides ample power for tackling tough jobs. The engine not only offers impressive performance but is also designed for fuel efficiency, allowing users to work longer without the need for constant refueling. This makes it a practical choice for both hobbyists and professionals who require sustained power during extended cutting sessions.

The chainsaw boasts a 16-inch cutting bar, which strikes an ideal balance between maneuverability and cutting capacity. This length is suitable for handling a wide array of cutting tasks, enabling users to make precise cuts with ease. The chain is designed for smooth operation, ensuring that the saw glides through wood effortlessly.

Another key feature of the Poulan 413288 is its lightweight design. Weighing in at just under 10 pounds, this chainsaw is easy to handle, reducing user fatigue during longer work periods. The ergonomic handle adds to the overall comfort, providing a secure grip that enhances control during operation.

Safety is also a priority in the design of the Poulan 413288. It includes a chain brake that activates in the event of a kickback, preventing accidents and ensuring user safety. Additionally, the chainsaw features an automatic oiling system that keeps the chain lubricated and reduces wear, further promoting durability.

The Poulan 413288 incorporates innovative technologies such as the Easy Start feature, which minimizes the effort required to start the engine. This is especially beneficial for users who may not have extensive experience with chainsaws.

In summary, the Poulan 413288 combines power, efficiency, and safety in one compact package. With its advanced features, user-friendly design, and reliable performance, it stands out as a versatile tool for anyone in need of a dependable chainsaw. Whether you're a seasoned professional or a weekend warrior, the Poulan 413288 is designed to meet your cutting needs with ease and precision.
Top Page Image Contents