Poulan 411044, 96082000500 manual Service and Adjustments, Cleaning, Tiller

Page 12

MAINTENANCE

MUFFLER

Do not operate tiller without muffler. Do not tamper with exhaust system. Damaged mufflers or spark arresters could create a fire hazard. Inspect periodically and replace if necessary. If your engine is equipped with a spark arrester screen assembly, remove every 50 hours for cleaning and inspection. Replace if damaged.

SPARK PLUG

Replace spark plugs at the beginning of each tilling sea- son or after every 50 hours of use, whichever comes first. Spark plug type and gap setting are shown in “PRODUCT SPECIFICATIONS” on page 3 of this manual.

CLEANING

Do not clean your tiller when the engine and transmission are hot. We do not recommend using pressurized water (garden hose, etc.) to clean your unit unless the gasket area around the transmission and the engine muffler, air filter and carburetor are covered to keep water out. Water in engine will shorten the useful life of your tiller.

•Clean engine, wheels, finish, etc. of all foreign mat- ter.

•Keep finished surfaces and wheels free of all gasoline, oil, etc.

•Protect painted surfaces with automotive type wax.

TRANSMISSION

Your transmission is sealed and will not require lubrication unless serviced.

SERVICE AND ADJUSTMENTS

CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug.

TILLER

TO ADJUST HANDLE HEIGHT (See Fig. 15)

Factory assembly has provided lowest handle height. Select handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil.

•If a higher handle height is desired, loosen the four nuts securing handle panel to engine brackets.

•Slide handle panel to desired location.

•Tighten the four nuts securely.

ENGINE BRACKETS

HANDLE

PANEL

NUTS (ALSO 2

ON LEFT SIDE

OF TILLER)

FIG. 15

TINE ARRANGEMENT

NORMAL TILLING - 26" PATH (See Fig. 16)

•Assemble holes “A” in tine hubs to holes “B” in tine shaft.

CLEVIS

OUTER

PIN

TINE

A

A

 

B

B

tine_4

 

HAIRPIN CLIP

INNER TINE

FIG. 16

MID-WIDTH TILLING - 24" PATH (See Fig. 17)

•Assemble holes “A” in tine hubs to holes “C” in tine shaft.

A

C

C

A

tine_5

 

 

 

FIG. 17

Your outer tines can be assembled in several different ways to suit your tilling or cultivating needs.

CAUTION: Tines are sharp. Wear gloves or other protection when han- dling tines.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents HDF825X Operators Manual ModelSafety Rules Maintenance and StorageTraining PreparationTable of Contents Assembly Tools Required for AssemblyContents of Hardware Pack Unpack Carton & Install Handle See Fig Handle HeightTilling Width Tine OperationMeets Ansi Safety Requirements OperationKnow Your Tiller HOW to USE Your Tiller Stopping See FigTine Operation See Fig TillingBefore Starting Engine To TransportFill Engine with OIL See Fig ADD GasolineBreaking in Your Tiller Tilling HintsCultivating Maintenance Maintenance ScheduleGeneral Recommendations AIR Cleaner See Fig EngineCooling System See Fig To Change Engine OIL See FigsService and Adjustments CleaningTiller Tine Operation Check See Fig To Remove Belt Guard See FigTo Replace V-BELTS See Figs Final Check OFF PositionTo Adjust Carburetor Belt ReplacementBelt Removal Check Tine OperationStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionLimited Warranty Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Dépannage DE Guide PasEntreposage Supplementaire InformationMoteur MotobineuseRéglages ET Révision Carburateur LE Régler Pour15 22 .FIG 21 .FIGFig la Voir Roiecour DE Protecteur LE Enlever Pour Fig la Voir Sesfrai DES L’UTILISATION DE Vérification Fraises DES Disposition 15 .FIGFig la Voir Guidon DU Hauteur LA Régler PourEntretien Nettoyage’ALLUMAGE Bougie SilencieuxMoteur Fig la Voir AIR À FiltreLubrification Générales Recommandations Lubrification DE Tableau’ENTRETIEN Calendrier LubrificationUtilisation Labourage DE ConseilsMotobineuse LA DE Rodage CultureMoteur LE Démarrer DE Avant Moteur LE Démarrer Pour’ESSENCE Réservoir LE Remplir ’HUILE Moteur LE RemplirBineuse Moto Votre Utiliser CommentLabourage Fig la FRAISESVoir DES UtilisationMotobineuse Votre Connaissez Motobineuse VotreMoteur le démarrer de permet Démarrage DE Poignée Manuel ce ConservezManche LE Installer ET Déballer MontageGeraboula DU Largeur Dents DES UtilisationPièces DES SAC DU Contenu Fig la Voir D’OPERATEUR PositionMontage LE Pour Exiges Outils LES De Clés 2 Pince 1 Tournevis 1 usage tout à CouteauSommaire Produit DU SpécificationsClient DU Responsabilités Réglages ET Révision Client DU ResponsabilitésSécurité DE Règles Entreposage ET EntretienMotobineuses des Sécurité toute En lUtilisation pour ConseilsOpérateur DU ManuelAvertissement

411044, 96082000500 specifications

Poulan 96082000500 and 411044 are two robust chainsaw models known for their reliability and performance. Poulan, a brand renowned for its outdoor power equipment, has designed these chainsaws with specific features that cater to both professional users and homeowners who need powerful and efficient tools for yard work or maintenance tasks.

The Poulan 96082000500 is equipped with a powerful 50cc two-stroke engine that offers impressive cutting power and efficiency. This engine provides a maximum speed that allows for quick cuts through wood, making it an excellent choice for felling trees, cutting firewood, or general yard work. The chainsaw features an easy-start system, which is essential for reducing the hassle of starting up the engine, especially for users who may not have extensive experience or strength.

One notable characteristic of the Poulan 96082000500 is its low-vibration technology. This feature minimizes the amount of vibration felt by the user, making it more comfortable to operate during extended periods. Additionally, it comes with a premium bar and chain that enhance cutting performance and longevity, ensuring the tool remains efficient over time.

On the other hand, the Poulan 411044 is designed for lighter tasks and is ideal for users who need a chainsaw for trimming and pruning. This model operates with a reliable 38cc engine that balances power with ease of use. The lightweight design is perfect for maneuverability, allowing users to navigate branches and shrubs effortlessly.

The 411044 also incorporates an automatic oiling system, which ensures that the chain remains lubricated during operation, reducing wear and extending the tool’s lifespan. This feature is particularly beneficial for those who may forget to manually oil the chain, providing a more forgiving user experience.

Both chainsaws feature safety mechanisms, including a chain brake that instantly stops the chain if kickback occurs, thus enhancing user safety. Easy-access filters and tool-less chain tensioning add to the convenience, allowing for quick maintenance and adjustments without the need for extra tools.

In summary, the Poulan 96082000500 and 411044 stand out in the market for their powerful engines, user-friendly features, and emphasis on safety. They cater to a diverse range of users, from seasoned professionals to beginners, providing reliability and performance in outdoor tasks.
Top Page Image Contents