Poulan 96082000500, 411044 manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 15

STORAGE

Immediately prepare your tiller for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the tiller with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TILLER

•Clean entire tiller (See “CLEANING” in the Maintenance section of this manual).

•Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

•Lubricate as shown in the Maintenance section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS THE CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent.

•Use fresh fuel next season.

NOTE: Fuel stablizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stablizer container. Run engine at least 10 minutes after adding stablizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

•Remove spark plug.

•Pour 1 ounce (29 ml) of oil through spark plug hole into cylinder.

•Pull starter handle slowly several times to distribute oil.

•Replace with new spark plug.

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your unit indoors and cover it to give protection from dust and dirt.

•Cover your unit with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your unit to rust.

IMPORTANT: NEVER COVER TILLER WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Operators Manual Model HDF825XPreparation Safety RulesMaintenance and Storage TrainingTable of Contents Assembly Tools Required for AssemblyContents of Hardware Pack Tine Operation Unpack Carton & Install Handle See FigHandle Height Tilling WidthMeets Ansi Safety Requirements OperationKnow Your Tiller Tilling HOW to USE Your TillerStopping See Fig Tine Operation See FigADD Gasoline Before Starting EngineTo Transport Fill Engine with OIL See FigBreaking in Your Tiller Tilling HintsCultivating Maintenance Maintenance ScheduleGeneral Recommendations To Change Engine OIL See Figs AIR Cleaner See FigEngine Cooling System See FigService and Adjustments CleaningTiller Final Check OFF Position Tine Operation Check See FigTo Remove Belt Guard See Fig To Replace V-BELTS See FigsCheck Tine Operation To Adjust CarburetorBelt Replacement Belt RemovalEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsLimited Warranty Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Pas Dépannage DE GuideMotobineuse EntreposageSupplementaire Information Moteur21 .FIG Réglages ET RévisionCarburateur LE Régler Pour 15 22 .FIGFig la Voir Roiecour DE Protecteur LE Enlever Pour Guidon DU Hauteur LA Régler Pour Fig la Voir Sesfrai DES L’UTILISATION DE VérificationFraises DES Disposition 15 .FIG Fig la VoirSilencieux EntretienNettoyage ’ALLUMAGE BougieMoteur Fig la Voir AIR À FiltreLubrification Lubrification Générales RecommandationsLubrification DE Tableau ’ENTRETIEN CalendrierCulture UtilisationLabourage DE Conseils Motobineuse LA DE Rodage’HUILE Moteur LE Remplir Moteur LE Démarrer DE AvantMoteur LE Démarrer Pour ’ESSENCE Réservoir LE RemplirFig la FRAISESVoir DES Utilisation BineuseMoto Votre Utiliser Comment LabourageManuel ce Conservez Motobineuse Votre ConnaissezMotobineuse Votre Moteur le démarrer de permet Démarrage DE PoignéeDents DES Utilisation Manche LE Installer ET DéballerMontage Geraboula DU LargeurDe Clés 2 Pince 1 Tournevis 1 usage tout à Couteau Pièces DES SAC DU ContenuFig la Voir D’OPERATEUR Position Montage LE Pour Exiges Outils LESRéglages ET Révision Client DU Responsabilités SommaireProduit DU Spécifications Client DU ResponsabilitésEn lUtilisation pour Conseils Sécurité DE RèglesEntreposage ET Entretien Motobineuses des Sécurité touteOpérateur DU ManuelAvertissement

411044, 96082000500 specifications

Poulan 96082000500 and 411044 are two robust chainsaw models known for their reliability and performance. Poulan, a brand renowned for its outdoor power equipment, has designed these chainsaws with specific features that cater to both professional users and homeowners who need powerful and efficient tools for yard work or maintenance tasks.

The Poulan 96082000500 is equipped with a powerful 50cc two-stroke engine that offers impressive cutting power and efficiency. This engine provides a maximum speed that allows for quick cuts through wood, making it an excellent choice for felling trees, cutting firewood, or general yard work. The chainsaw features an easy-start system, which is essential for reducing the hassle of starting up the engine, especially for users who may not have extensive experience or strength.

One notable characteristic of the Poulan 96082000500 is its low-vibration technology. This feature minimizes the amount of vibration felt by the user, making it more comfortable to operate during extended periods. Additionally, it comes with a premium bar and chain that enhance cutting performance and longevity, ensuring the tool remains efficient over time.

On the other hand, the Poulan 411044 is designed for lighter tasks and is ideal for users who need a chainsaw for trimming and pruning. This model operates with a reliable 38cc engine that balances power with ease of use. The lightweight design is perfect for maneuverability, allowing users to navigate branches and shrubs effortlessly.

The 411044 also incorporates an automatic oiling system, which ensures that the chain remains lubricated during operation, reducing wear and extending the tool’s lifespan. This feature is particularly beneficial for those who may forget to manually oil the chain, providing a more forgiving user experience.

Both chainsaws feature safety mechanisms, including a chain brake that instantly stops the chain if kickback occurs, thus enhancing user safety. Easy-access filters and tool-less chain tensioning add to the convenience, allowing for quick maintenance and adjustments without the need for extra tools.

In summary, the Poulan 96082000500 and 411044 stand out in the market for their powerful engines, user-friendly features, and emphasis on safety. They cater to a diverse range of users, from seasoned professionals to beginners, providing reliability and performance in outdoor tasks.
Top Page Image Contents