Poulan 96092002200, 433107 Maintenance Schedule, General Recommendations, Lubrication Chart

Page 11

MAINTENANCE

MAINTENANCE

MAINTENANCE SCHEDULE

FILL IN DATES

AS YOU COMPLETE REGULAR SERVICE

	EACH	USE		HOURS		HOURS		HOURS SEASON
BEFORE			5		25		50
	EVERY			EVERY		EVERY		EVERY

SERVICE DATES

Check Engine Oil Level

Change Engine Oil

1,2

Oil Pivot Points

Inspect Spark Arrester / Muffler

Inspect Air Screen

Clean or Replace Air Cleaner Cartridge

2

Clean Engine Cylinder Fins

Replace Spark Plug

RH Gear Case Grease Fitting (1oz.)

1 - Change more often when operating under a heavy load or in high ambient temperatures. 2 - Service more often when operating in dirty or dusty conditions.

GENERAL RECOMMENDATIONS

The warranty on this tiller does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain tiller as instructed in this manual.

Some adjustments will need to be made periodically to properly maintain your tiller.

All adjustments in the Service and Adjustments section of this manual should be checked at least once each season.

•Once a year you should replace the spark plug, clean or replace air filter, and check tines and belts for wear. A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better and last longer.

BEFORE EACH USE

•Check engine oil level.

•Check tine operation.

•Check for loose fasteners.

LUBRICATION

Keep unit well lubricated (See “LUBRICATION CHART”).

LUBRICATION CHART

d ENGINE

eRH GEAR CASE

GREASE FITTIG

c DEPTH STAKE PIN

c LEVELING

SHIELD

HINGES

cIDLER

BRACKET	c WHEEL
	HUB

c SAE 30 OR 10W-30 MOTOR OIL

d REFER TO MAINTENANCE “ENGINE” SECTION eEP #1 GREASE

11

Image 11

Contents REAR TINE TILLER MODELIMPORTANT MANUAL OPERATORS MANUALPREPARATION SAFETY RULESMAINTENANCE AND STORAGE TRAININGCUSTOMER RESPONSIBILITIES TABLE OF CONTENTSPRODUCT SPECIFICATIONS OPERATOR’S POSITION See Fig ASSEMBLYTOOLS REQUIRED FOR ASSEMBLY CONTENTS OF HARDWARE PACKUNPACKING CARTON See Fig INSTALL HANDLE See Figs. 3, 4, andCHECK TIRE PRESSURE ATTACH CLUTCH CABLE See FigCONNECT SHIFT ROD See Fig REMOVE TILLER FROM CRATEKNOW YOUR TILLER MEETS ANSI SAFETY REQUIREMENTSOPERATION FORWARD - WHEELS ONLY/TINES STOPPED HOW TO USE YOUR TILLERSTOPPING See Fig TINE OPERATION - WITH WHEEL DRIVEADD GASOLINE BEFORE STARTING ENGINETO TRANSPORT CHECK ENGINE OIL LEVEL See Fig.12SPARK PLUG THROTTLE CONTROL CHOKE CONTROL RECOIL TINE SHEAR PINSTILLING HINTS CULTIVATINGSERVICE DATES MAINTENANCEMAINTENANCE SCHEDULE LUBRICATION CHARTENGINE AIR CLEANER See FigSPARK PLUG CLEANINGCOOLING SYSTEM See Fig MUFFLERTO REMOVE BELT GUARD See Fig SERVICE AND ADJUSTMENTSTO ADJUST HANDLE HEIGHT See Fig TILLERTO REPLACE GROUND DRIVE BELT See Fig GROUND DRIVE BELT ADJUSTMENT See FigTINE REPLACEMENT See Figs. 24, 25 and TO ADJUST CARBURETOR ENGINE OIL STORAGEOTHER FUEL SYSTEMTROUBLESHOOTING POINTS LIMITED WARRANTY SERVICE NOTES PARTS AND SERVICE CHANGERE DE PIÈCES LES ET L’ENTRETIEN DENTRETIEN REMARQUES LIMITÉE GARANTIE PROBLEME DÉPANNAGE DE GUIDEMOTOBINEUSE ENTREPOSAGESUPPLEMENTAIRE INFORMATION MOTEURCARBURATEUR LE RÉGLER POUR RÉGLAGES ET RÉVISION26 et Fig les Voir FRAISES DES REMPLACEMENTTERRE À TRAÎNEMENT 23 et 22 .Fig les VoirD’ENCOURROIE LA REMPLACER POUR 20 .Fig la Voir GUIDON DU HAUTEUR LA RÉGLER POUR MOTOBINEUSE21 .Fig la Voir ROUE LA ENLEVER POUR 22 .Fig la Voir ROIE19 .Fig la Voir ENTRETIENNETTOYAGE D’ALLUMAGE BOUGIELUBRIFICATION MOTEUR18 .Fig la Voir AIR À FILTRE D’ENTRETIEN DATES GÉNÉRALES RECOMMANDATIONSLUBRIFICATION DE TABLEAU D’ENTRETIEN CALENDRIERDENTS DES CISAILLEMENT DE BOULONS UTILISATIONBINAGE LABOURAGE DE CONSEILS12 .Fig la Voir MOTEUR LE DÉMARRER DE AVANT13 .Fig la Voir MOTEUR LE DÉMARRER POUR10 .Fig la Voir PROFONDEUR DE JAUGE BINEUSEMOTOVOTRE UTILISER COMMENT 11 .Fig la Voir LABOURAGEMOTOBINEUSE VOTRE CONNAISSEZ PNEU DE PRESSION LA VERIFIER MONTAGE6 .Fig la Voir POIGNEE DE HAUTEUR5 .Fig POIGNEE LA INSTALLER5 et 4, 3, .Fig les Voir 2 .Fig la Voir CARTON LE DEBALLER1 .Fig PIÈCES DES SAC DU CONTENU1 .Fig la Voir D’OPERATEUR POSITION MONTAGE LE POUR EXIGES OUTILS LESPRODUIT DE SPÉCIFICATIONS SOMMAIRECLIENT DU RESPONSABILITÉS FORMATION ENTREPOSAGE ET ENTRETIENUTILISATION PRÉPARATIONIMPORTANT MANUEL MOTOBINEUSEMODÈLE PROPRIÉTAIRE DU MANUEL PAS JETEZ NE