Poulan 433107 manual Service And Adjustments, Tiller, TO ADJUST HANDLE HEIGHT See Fig, Tire Care

Page 14

SERVICE AND ADJUSTMENTS

SERVICE AND ADJUSTMENTS

CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug.

TILLER

TO ADJUST HANDLE HEIGHT (See Fig. 20)

Select handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil.

•First loosen handle lock lever.

•Handle can be positioned at different settings between “HIGH” and “LOW” positions.

•Retighten handle lock lever securely after adjusting.

HANDLE

(HIGH POSITION)

HANDLE LOCK

LEVER

HANDLE

(LOW POSITION)

Fig. 20

CLEVIS PIN

HAIRPIN CLIP

Fig. 21

TO REMOVE BELT GUARD (See Fig. 22)

NOTE: For ease of removal, remove hairpin clip and clevis pin from left wheel. Pull wheel out from tiller about 1 inch.

•Remove two (2) screws from side of belt guard.

•Remove hex nut and washer from bottom of belt guard (located behind wheel).

•Pull belt guard out and away from unit.

•Replace belt guard by reversing above procedure.

TIRE CARE

CAUTION: When mounting tires, un- less beads are seated, overinflation can cause an explosion.

•Maintain 20 pounds of tire pressure. If tire pressures are not equal, tiller will pull to one side.

•Keep tires free of gasoline or oil which can damage rubber.

TO REMOVE WHEEL (See Fig. 21)

•Place blocks under transmission to keep tiller from tipping.

•Remove hairpin clip and clevis pin from wheel.

•Remove wheel and tire.

•Repair tire and reassemble.

BELT GUARD	SCREW
	AND WASHER	HEX NUT
		HEX NUT
		AND WASHER
		(LOCATED
		BEHIND
		TIRE)

	SCREW
	AND	HAIRPIN CLIP AND
	WASHER	HAIRPIN CLIP AND
	WASHER	CLEVIS PIN
		CLEVIS PIN

Fig. 22

14

Image 14

Contents OPERATORS MANUAL MODELIMPORTANT MANUAL REAR TINE TILLERTRAINING SAFETY RULESMAINTENANCE AND STORAGE PREPARATIONCUSTOMER RESPONSIBILITIES TABLE OF CONTENTSPRODUCT SPECIFICATIONS CONTENTS OF HARDWARE PACK ASSEMBLYTOOLS REQUIRED FOR ASSEMBLY OPERATOR’S POSITION See FigINSTALL HANDLE See Figs. 3, 4, and UNPACKING CARTON See FigREMOVE TILLER FROM CRATE ATTACH CLUTCH CABLE See FigCONNECT SHIFT ROD See Fig CHECK TIRE PRESSUREKNOW YOUR TILLER MEETS ANSI SAFETY REQUIREMENTSOPERATION TINE OPERATION - WITH WHEEL DRIVE HOW TO USE YOUR TILLERSTOPPING See Fig FORWARD - WHEELS ONLY/TINES STOPPEDCHECK ENGINE OIL LEVEL See Fig.12 BEFORE STARTING ENGINETO TRANSPORT ADD GASOLINECULTIVATING TINE SHEAR PINSTILLING HINTS SPARK PLUG THROTTLE CONTROL CHOKE CONTROL RECOILLUBRICATION CHART MAINTENANCEMAINTENANCE SCHEDULE SERVICE DATESAIR CLEANER See Fig ENGINEMUFFLER CLEANINGCOOLING SYSTEM See Fig SPARK PLUGTILLER SERVICE AND ADJUSTMENTSTO ADJUST HANDLE HEIGHT See Fig TO REMOVE BELT GUARD See FigGROUND DRIVE BELT ADJUSTMENT See Fig TO REPLACE GROUND DRIVE BELT See FigTINE REPLACEMENT See Figs. 24, 25 and TO ADJUST CARBURETOR FUEL SYSTEM STORAGEOTHER ENGINE OILTROUBLESHOOTING POINTS LIMITED WARRANTY SERVICE NOTES PARTS AND SERVICE CHANGERE DE PIÈCES LES ET L’ENTRETIEN DENTRETIEN REMARQUES LIMITÉE GARANTIE DÉPANNAGE DE GUIDE PROBLEMEMOTEUR ENTREPOSAGESUPPLEMENTAIRE INFORMATION MOTOBINEUSERÉGLAGES ET RÉVISION CARBURATEUR LE RÉGLER POURFig les Voir FRAISES DES REMPLACEMENT 26 etTERRE À TRAÎNEMENT 23 et 22 .Fig les VoirD’ENCOURROIE LA REMPLACER POUR 22 .Fig la Voir ROIE MOTOBINEUSE21 .Fig la Voir ROUE LA ENLEVER POUR 20 .Fig la Voir GUIDON DU HAUTEUR LA RÉGLER POURD’ALLUMAGE BOUGIE ENTRETIENNETTOYAGE 19 .Fig la VoirLUBRIFICATION MOTEUR18 .Fig la Voir AIR À FILTRE D’ENTRETIEN CALENDRIER GÉNÉRALES RECOMMANDATIONSLUBRIFICATION DE TABLEAU D’ENTRETIEN DATESLABOURAGE DE CONSEILS UTILISATIONBINAGE DENTS DES CISAILLEMENT DE BOULONSMOTEUR LE DÉMARRER POUR MOTEUR LE DÉMARRER DE AVANT13 .Fig la Voir 12 .Fig la Voir11 .Fig la Voir LABOURAGE BINEUSEMOTOVOTRE UTILISER COMMENT 10 .Fig la Voir PROFONDEUR DE JAUGEMOTOBINEUSE VOTRE CONNAISSEZ POIGNEE DE HAUTEUR MONTAGE6 .Fig la Voir PNEU DE PRESSION LA VERIFIER2 .Fig la Voir CARTON LE DEBALLER POIGNEE LA INSTALLER5 et 4, 3, .Fig les Voir 5 .FigMONTAGE LE POUR EXIGES OUTILS LES PIÈCES DES SAC DU CONTENU1 .Fig la Voir D’OPERATEUR POSITION 1 .FigPRODUIT DE SPÉCIFICATIONS SOMMAIRECLIENT DU RESPONSABILITÉS PRÉPARATION ENTREPOSAGE ET ENTRETIENUTILISATION FORMATIONPAS JETEZ NE MOTOBINEUSEMODÈLE PROPRIÉTAIRE DU MANUEL IMPORTANT MANUEL