Poulan 432822 manual Unpack Carton & Install Handle See Fig, Install Depth Stake Assembly See Fig

Page 5

ASSEMBLY

UNPACK CARTON & INSTALL HANDLE (See Fig. 1)

CAUTION: Be careful of exposed staples when handling or disposing of carton material.

IMPORTANT: WHEN UNPACKING AND ASSEMBLING TILLER, BE CAREFUL NOT TO STRETCH OR KINK CABLE(S).

•Cut cable ties securing handle column.

•Route cable(s) as shown and slide handle column onto handle mount.

•Remove all packing from carton.

•Secure handle column using two (2) carriage bolts and two (2) flange locknuts. Tighten securely.

•Cut away carton.

•Route tine control cable(s) through plastic cable clip on handle mount.

NOTE: Cables must not touch the muffler.

•Cut cable ties securing tiller to skid. Remove tiller from skid by pulling backwards.

•Remove screws securing depth stake to skid and discard the screws.

Tine Control

Tine

Control

Cable

Handle

Column

Handle

Mount

Carriage

Bolt

Flange

Locknut

Fig. 1

INSTALL DEPTH STAKE ASSEMBLY (See Fig. 2)

•Loosen nut “A”.

•Insert stake support between engine bracket halves with stake spring down.

•Bolt stake support to engine brackets with bolts, lock washers and nuts. Tighten securely. Tighten nut “A”.

•Depth stake must move freely. If it does not, loosen support bolt.

Engine Bracket Halves

Nut “A”

Depth Stake Support

Depth

Stake

Support Bolt

Stake Spring

Hex Bolts, Lock Washers, and hex Nuts

Fig. 2

HANDLE HEIGHT

•Handle height may be adjusted to better suit operator. (See “HANDLE HEIGHT” in the Service and Adjust- ments section of this manual).

TILLING WIDTH

•Tilling width may be adjusted to better handle your tilling conditions (See “TINE ARRANGEMENT” in the Service and Adjustments section of this manual).

TINE OPERATION

•Check tine operation before first use. (See “TINE OPERATION CHECK” in the Service and Adjustments section of this manual).

5

Image 5

Contents Operators Manual Model FT900Maintenance and Storage Safety RulesTraining PreparationTable of Contents OPERATOR’S Position See Fig AssemblyTools Required for Assembly Install Depth Stake Assembly See Fig Unpack Carton & Install Handle See FigHandle Height Tilling WidthKnow Your Tiller Meets Ansi Safety RequirementsOperation Stopping See Fig HOW to USE Your TillerTilling To TransportCheck Engine OIL Level See Fig Before Starting EngineADD Gasoline Around TownCultivating Breaking in Your TillerTilling Hints Lubrication Chart MaintenanceGeneral Recommendations Before Each USETo Change Engine OIL See Figs AIR Cleaner See FigEngine Cooling System See Fig CleaningMuffler Spark PlugTo Adjust Handle Height See Fig Service and AdjustmentsTiller Tine ArrangementTo Replace V-BELT See Fig To Remove Belt Guard See FigOther StorageFuel System Engine OILWill not start Troubleshooting PointsLimited Warranty Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Limitée Garantie Pas Dépannage DE GuideCylindres EntreposageMoteur DE Huile Dalimentation SystèmeFig la Voir Réglages ET RévisionFig la Voir Roie Ledazoïpétra Courroie LA RemplacerFig la Voir Guidon DU Hauteur LA Régler Pour MotobineuseSesfrai DES Dutilisation Vérification Fraises DES Disposition’ALLUMAGE Bougie EntretienSilencieux Refroidissement DE SystèmeMoteur Dhuile Remplacer Pour Fig la Voir AIR À FiltreLubrification Tendeur-Galet De Bras Moteur Utilisation Chaque AvantLabourage DE Conseils UtilisationMotobineuse LA DE Rodage CultureLa Voir D’HUILE Moteur LE Remplir Fig la Voir Moteur DU Démarrage’ESSENCE Réservoir LE Remplir Moteur DU Démarrage LE AvantFig la Voir Arrêt LabourageTransporter Pour Dents DES FonctionnementDemarrage DE Poignee Motobineuse VotreLabour DE Largeur Profondeur DE Jauge LA InstallerMontage Montage LE Pour Exiges Outils LES Fig la Voir D’OPERATEUR PositionProduit DU Spécifications SommaireClient DU Responsabilités Réglages ET Révision Client DU ResponsabilitésEntreposage ET Entretien Sécurité DE RèglesMotobineuses des Sécurité toute En lUtilisation pour ConseilsU in Printed ModèleOpérateur DU Manuel