Unpack Carton & Install Handle See Fig | Poulan 96082001100 manual

Poulan 96082001100 manual Unpack Carton & Install Handle See Fig, Handle Height, Tilling Width

Page 5

ASSEMBLY

UNPACK CARTON & INSTALL HANDLE (See Fig. 2)

CAUTION: Be careful of exposed staples when handling or disposing of cartoning material.

IMPORTANT: WHEN UNPACKING AND ASSEMBLING TILLER, BE CAREFUL NOT TO STRETCH OR KINK CABLE(S).

•Cut cable ties securing handles.

•Slowly lift handle assembly up, route cable(s) as shown and align handle holes with handle panel hole and slot.

•Loosely assemble hardware as shown. Be sure the shorter (1" long) hex bolt is assembled in lower hole of handle. Repeat for opposite side. Tighten all hard- ware securely.

•Cut cable ties securing tiller to skid and remove tiller from skid.

•Remove screws securing depth stake to skid and dis- card the screws.

LOCK

NUT WASHER TILLER

HANDLE

	HANDLE	FLAT
	PANEL
		WASHER

INSTALL DEPTH STAKE ASSEMBLY (See Fig. 3)

•Loosen nut “A”.

•Insert stake support between engine bracket halves with stake spring down.

•Bolt stake support to engine brackets with bolts, lock washers and nuts. Tighten securely. Tighten nut “A”.

•Depth stake must move freely. If it does not, loosen support bolt.

dept		ENGINE BRACKET
dept		HALVES
h
_
s
	t
	a		NUT “A”
	k
	e
	_4
			DEPTH
			STAKE
			DEPTH STAKE
			SUPPORT
			SUPPORT
			BOLT
			STAKE
		HEX BOLTS,	SPRING
		HEX BOLTS,
		LOCK WASHERS,
		AND HEX NUTS

&4(ANDLEª0ANEL?

CABLE(S)

TILLER

HANDLES

HEX BOLT 5/16-18X1-1/4"

HEX BOLT 5/16-18X1"

	1
020	5
020

HANDLE

PANEL

BOLTS

FIG. 3

HANDLE HEIGHT

•Handle height may be adjusted to better suit operator. (See “HANDLE HEIGHT” in the Service and Adjust- ments section of this manual).

TILLING WIDTH

•Tilling width may be adjusted to better handle your tilling conditions (See “TINE ARRANGEMENT” in the Service and Adjustments section of this manual).

TINE OPERATION

•Check tine operation before first use. (See “TINE OP- ERATION CHECK” in the Service and Adjustments section of this manual).

FIG. 2

Image 5

Contents

Operators Manual Model HDF800XMaintenance and Storage Safety RulesTraining PreparationTable of Contents Contents of Hardware Pack AssemblyTools Required for Assembly Handle Height Unpack Carton & Install Handle See FigTilling Width Tine OperationKnow Your Tiller Meets Ansi Safety RequirementsOperation Stopping See Fig HOW to USE Your TillerTine Operation See Fig TillingTo Transport Before Starting EngineFill Engine with OIL See Fig ADD GasolineTilling Hints Breaking in Your TillerCultivating This. First, wide turns are much easier to negotiate thanGeneral Recommendations MaintenanceMaintenance Schedule Engine AIR Cleaner See FigCooling System See Fig To Change Engine OIL See FigsTiller Service and AdjustmentsCleaning To Remove Belt Guard See Fig Tine Operation Check See FigTo Replace V-BELTS See Figs Final Check OFF PositionBelt Replacement To Adjust CarburetorBelt Removal Check Tine OperationOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsLimited Warranty Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Pas Dépannage DE GuideSupplementaire Information EntreposageMoteur MotobineuseMoteur Réglages ET RévisionCarburateur LE Régler Pour 22 .FIGFig la Voir Roiecour DE Protecteur LE Enlever Pour Fig la Voir Sesfrai DES L’UTILISATION DE Vérification MotobineuseFraises DES Disposition 15 .FIG Fig la Voir Guidon DU Hauteur LA Régler PourNettoyage Entretien’ALLUMAGE Bougie Fig la VoirLubrification Fig la Voir AIR À FiltreLubrification DE Tableau Générales Recommandations’ENTRETIEN Calendrier LubrificationLabourage DE Conseils UtilisationMotobineuse LA DE Rodage CultureMoteur LE Démarrer Pour Moteur LE Démarrer DE Avant’ESSENCE Réservoir LE Remplir ’HUILE Moteur LE RemplirMoto Votre Utiliser Comment BineuseLabourage Fig la FRAISESVoir DES UtilisationMotobineuse Votre Motobineuse Votre ConnaissezMoteur le démarrer de permet Démarrage DE Poignée Manuel ce ConservezMontage Manche LE Installer ET DéballerGeraboula DU Largeur Dents DES UtilisationFig la Voir D’OPERATEUR Position Pièces DES SAC DU ContenuMontage LE Pour Exiges Outils LES De Clés 2 Pince 1 Tournevis 1 usage tout à CouteauProduit DU Spécifications SommaireClient DU Responsabilités Réglages ET Révision Client DU ResponsabilitésEntreposage ET Entretien Sécurité DE RèglesMotobineuses des Sécurité toute En lUtilisation pour ConseilsAux Imprimé CL 09.31.01 1 .Rev ModèleOpérateur DU Manuel

Related manuals

Poulan 96082001100 manual Unpack Carton & Install Handle See Fig, Handle Height, Tilling Width