HOW to USE Your Tiller, Stopping See Fig

Poulan 96082001100 HOW to USE Your Tiller, Stopping See Fig, Tine Operation See Fig, Tilling

Page 7

OPERATION

The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask for over spectacles or standard safety glasses.

HOW TO USE YOUR TILLER

Know how to operate all controls before adding fuel and oil or attempting to start engine.

STOPPING (See Fig. 5)

TINES

•Release forward tine control to stop forward move- ment.

•Release reverse tine control to stop reverse move- ment.

ENGINE

•Move throttle control to “STOP” position.

•Never use choke to stop engine.

					FORWARD TINE CONTROL IN
			REVERSE		“OFF” (UP) POSITION
			REVERSE
			CONTROL
					FORWARD TINE CONTROL
					IN “ON” (DOWN) POSITION
	_	9	4
	_	9
hand	l es
hand
					THROTTLE
					CONTROL
CHOKE
CONTROL
			eng
			in
				e_ar
				t_
				71

FIG. 5

TINE OPERATION (See Fig. 5)

FORWARD

•Squeeze forward tine control to handle.

REVERSE

•With forward tine control “OFF” (up) position, pull back and hold reverse tine control.

TILLING

The speed and depth of tilling is regulated by the position of the depth stake and wheel height.

The depth stake should always be below the wheels for digging. It serves as a brake to slow the tiller’s forward motion to enable the tines to penetrate the ground. Also, the more the depth stake is lowered into the ground the deeper the tines will dig.

DEPTH STAKE (See Fig. 6)

Adjust depth stake by removing the hairpin clip and clevis pin. Change depth stake to desired position. Replace the clevis pin and hairpin clip.

•For normal tilling, set depth stake at the second or third hole from the top.

WHEELS (See Fig. 6)

Adjust wheels by removing the hairpin clip and clevis pin. Change wheel position. Replace the hairpin clip and clevis pin.

•For normal tilling, set wheels at the second or third hole from the top.

dept			HAIRPIN CLIP
dept			AND CLEVIS PIN
h
_
s
	t
	a
	k
	e
	_
	4
			DEPTH
		STAKE	STAKE
		STAKE
		SPRING
		WHEEL

FIG. 6

Image 7

Contents

Operators Manual Model HDF800XPreparation Safety RulesMaintenance and Storage TrainingTable of Contents Tools Required for Assembly AssemblyContents of Hardware Pack Tine Operation Unpack Carton & Install Handle See FigHandle Height Tilling WidthOperation Meets Ansi Safety RequirementsKnow Your Tiller Tilling HOW to USE Your TillerStopping See Fig Tine Operation See FigADD Gasoline Before Starting EngineTo Transport Fill Engine with OIL See FigThis. First, wide turns are much easier to negotiate than Breaking in Your TillerTilling Hints CultivatingMaintenance Schedule MaintenanceGeneral Recommendations To Change Engine OIL See Figs AIR Cleaner See FigEngine Cooling System See FigCleaning Service and AdjustmentsTiller Final Check OFF Position Tine Operation Check See FigTo Remove Belt Guard See Fig To Replace V-BELTS See FigsCheck Tine Operation To Adjust CarburetorBelt Replacement Belt RemovalEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsLimited Warranty Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Pas Dépannage DE GuideMotobineuse EntreposageSupplementaire Information Moteur22 .FIG Réglages ET RévisionMoteur Carburateur LE Régler PourFig la Voir Roiecour DE Protecteur LE Enlever Pour Fig la Voir Guidon DU Hauteur LA Régler Pour MotobineuseFig la Voir Sesfrai DES L’UTILISATION DE Vérification Fraises DES Disposition 15 .FIGFig la Voir EntretienNettoyage ’ALLUMAGE BougieLubrification Fig la Voir AIR À FiltreLubrification Générales RecommandationsLubrification DE Tableau ’ENTRETIEN CalendrierCulture UtilisationLabourage DE Conseils Motobineuse LA DE Rodage’HUILE Moteur LE Remplir Moteur LE Démarrer DE AvantMoteur LE Démarrer Pour ’ESSENCE Réservoir LE RemplirFig la FRAISESVoir DES Utilisation BineuseMoto Votre Utiliser Comment LabourageManuel ce Conservez Motobineuse Votre ConnaissezMotobineuse Votre Moteur le démarrer de permet Démarrage DE PoignéeDents DES Utilisation Manche LE Installer ET DéballerMontage Geraboula DU LargeurDe Clés 2 Pince 1 Tournevis 1 usage tout à Couteau Pièces DES SAC DU ContenuFig la Voir D’OPERATEUR Position Montage LE Pour Exiges Outils LESRéglages ET Révision Client DU Responsabilités SommaireProduit DU Spécifications Client DU ResponsabilitésEn lUtilisation pour Conseils Sécurité DE RèglesEntreposage ET Entretien Motobineuses des Sécurité touteOpérateur DU Manuel ModèleAux Imprimé CL 09.31.01 1 .Rev

Related manuals

Poulan 96082001100 HOW to USE Your Tiller, Stopping See Fig, Tine Operation See Fig, Tilling