Crown Audio XLS 202 operation manual Specifications

Page 13

XLS Series Power Amplifiers

7 Specifications

Minimum Guaranteed Power (watts)

XLS202

XLS402

XLS602

120 VAC, 60 Hz Units, per channel, both channels driven

 

 

 

1 kHz with 0.1% THD

 

 

 

Stereo, 2 ohm (per ch.)

250

570

840

Stereo, 4 ohm (per ch.)

200

400

600

Stereo, 8 ohm (per ch.)

145

260

370

240 VAC, 50 Hz Units, per channel, both channels driven

 

 

 

1 kHz with 0.1% THD

 

 

 

Stereo, 2 ohm (per ch.)

260

610

880

Stereo, 4 ohm (per ch.)

225

445

670

Stereo, 8 ohm (per ch.)

155

275

400

Performance

XLS202

XLS402

XLS602

Sensitivity (volts RMS)

 

 

 

for full rated power at 4 ohms

0.725

1.025

1.26

Frequency Response (at 1 watt) 20Hz - 20kHz

± 0.75 dB

± 0.75 dB

± 0.75 dB

Phase Response (degrees at 1 watt)

 

 

 

at 10 Hz

–10

–10

–10

at 20 kHz

+19

+19

+19

Signal to Noise Ratio (20 Hz to 20 kHz)

 

 

 

A-weighted, below rated power

> 100 dB

> 100 dB

> 100 dB

No weighting, below rated power

> 97 dB

> 97 dB

> 97 dB

Total Harmonic Distortion (THD)

 

 

 

at full bandwidth power, from 20 Hz to 1 kHz

< 0.15%

< 0.15%

< 0.15%

Intermodulation Distortion (IMD)

 

 

 

60 Hz and 7 kHz at 4:1, from full rated output to –40 dB

< 0.3%

< 0.3%

< 0.3%

 

 

 

 

Damping Factor (8 ohm) 10Hz to 400Hz

> 200

> 200

> 200

Crosstalk, below rated power

 

 

 

at 1 kHz

–82 dB

–82 dB

–82 dB

at 20 kHz

–58 dB

–58 dB

–58 dB

Input Impedance

 

 

 

nominally balanced, nominally unbalanced

20 k ohms, 10 k ohms

20 k ohms, 10 k ohms

20 k ohms, 10 k ohms

Load Impedance (rated)

 

 

 

Note: Safe with all types of loads.

 

 

 

Stereo

2-8 ohms

2-8 ohms

2-8 ohms

Bridge-Mono

8 ohms

8 ohms

8 ohms

Voltage Gain (at maximum output)

31 dB

31 dB

31 dB

AC Line Voltage and Frequency Configurations Available (±10%)

120 VAC/60 Hz and 230 VAC/50 Hz

120 VAC/60 Hz and 230 VAC/50 Hz

120 VAC/60 Hz and 230 VAC/50 Hz

Operation Manual

page 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents XLS Series Do not defeat the safety purpose Important Safety InstructionsTable of Contents Features How to Use This ManualWelcome Unpacking Your AmplifierYou may also stack amps without using a cabinet SetupBe sure to operate your amplifi er from a power Distance Wire Your System 3.7.1 Stereo Mode Typical input and output wiring is shown in FigureBridge-Mono Mode Startup Procedure Setup OperationPrecautions Turn up the level of your audio source to an optimum levelPower Indicator Clip IndicatorsFault Indicator Power SwitchMale XLR Signal Links Power Connector FuseFilter Switches Limiter Switch230V Very low frequency signals contain no usefulXLS202 T6.3A T6.3A XLS402 T6.3A T10A XLS602This is normal operation for your amp TroubleshootingSpecifications Dimensions Width Air Volume Requirements per minute per unitNet Weight Shipping WeightTechnical Support / Factory Service ServiceFacsimile Internet Year WarrantyWorldwide Except USA & Canada XLS Series Power Amplifiers Model Crown Factory Service Information

XLS 202 specifications

Crown Audio XLS 202 is a power amplifier that stands out in the pro audio market for its robust performance and versatile application capabilities. Renowned for its reliability, the XLS 202 is ideally suited for live sound, fixed installations, and portable systems. One of its most notable attributes is its power output, delivering up to 300 watts per channel at 4 ohms, which ensures that it can drive a wide array of speaker systems with confidence.

One of the key features of the XLS 202 is the inclusion of advanced technology such as the Integrated Protection Circuitry. This system safeguards the amplifier from potential damage caused by overheating, overloads, or short circuits. By automatically adjusting performance based on the current operating conditions, it ensures longevity and reliability, which is crucial for demanding environments.

Additionally, the XLS 202 employs a lightweight and compact design, utilizing a switch-mode power supply that not only reduces weight but also provides efficient power management. This feature is particularly advantageous for mobile sound engineers who need to transport their equipment regularly. The amplifier's high-frequency response and low total harmonic distortion ensure that audio fidelity is maintained, allowing for a clear and powerful sound output that performers and audience members alike can appreciate.

The XLS 202 is equipped with XLR, TRS, and terminal block inputs, facilitating easy integration into various systems. Moreover, it features a comprehensive set of control options, including independent volume controls for each channel, as well as a high-pass filter that can be adjusted according to user preferences. These controls allow sound engineers to tailor the audio to specific venues, resulting in optimal sound quality.

Furthermore, the XLS series amplifiers come with a durable, rack-mountable chassis, designed to withstand the rigors of touring and regular use. The intuitive LED indicators on the front panel inform users about the operational status of the amplifier, providing real-time feedback on performance.

In summary, the Crown Audio XLS 202 combines exceptional power, advanced protective technology, and user-friendly features within a rugged design, making it an ideal choice for professionals seeking reliable amplification in a diverse range of applications. With its balance of power, functionality, and durability, the XLS 202 continues to be a preferred option for those in the audio industry.
Top Page Image Contents