Crown Audio XLS 202 operation manual Setup, You may also stack amps without using a cabinet

Page 5

XLS Series Power Amplifiers

3 Setup

3.1 Unpack Your Amplifier

YOU WILL NEED (not supplied):

• Two input wiring cables

• Two output wiring cables

•Rack for mounting amplifi er (or a stable surface for stacking)

WARNING: Before you start to set up your amplifier, make sure you read and observe the Important Safety Instruc- tions found at the beginning of this manual.

3.2 Voltage Selection

3.3 Mount Your Amplifier

CAUTION: Before you begin, make sure your amplifier is disconnected from the power source, with power switch in the “off” position and all level controls turned completely down (counterclock- wise).

Use a standard 19-inch (48.3 cm) equipment rack. See Figure 3.2 for amplifi er dimensions.

You may also stack amps without using a cabinet.

NOTE: When transporting, amplifi ers should be supported at both front and back.

3.4 Ensure Proper Cooling

When using an equipment rack, mount units directly on top of each other. Close any open spaces in rack with blank panels. DO NOT block side or front air vents.

Figure 3.3 illustrates standard amplifier air- flow.

CAUTION: Before use, your amplifier must be set to the correct operating voltage for your local supply. Typically, units are shipped from the factory with voltage already set with the correct setting, but this setting should be verifi ed before fi rst using the amplifi er.

The selected voltage is displayed on the top, left side of the fuse drawer (see Figure 3.1). To change the voltage setting; disconnect the power source, then gently pry out the fuse casing from the fuse drawer. Replace with the correct voltage positioned to display on the top left side.

Be sure to operate your amplifi er from a power

Figure 3.1 supply within ±10% of the rated voltage (i.e., Voltage Selection 108-132V for 120V supply).

2 in.

Figure 3.3 Airflow

Figure 3.2 Dimensions

Operation Manual

page 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents XLS Series Do not defeat the safety purpose Important Safety InstructionsTable of Contents Features How to Use This ManualWelcome Unpacking Your AmplifierBe sure to operate your amplifi er from a power SetupYou may also stack amps without using a cabinet Distance Bridge-Mono Mode Typical input and output wiring is shown in FigureWire Your System 3.7.1 Stereo Mode Startup Procedure Setup OperationPrecautions Turn up the level of your audio source to an optimum levelPower Indicator Clip IndicatorsFault Indicator Power SwitchMale XLR Signal Links Power Connector FuseFilter Switches Limiter Switch230V Very low frequency signals contain no usefulXLS202 T6.3A T6.3A XLS402 T6.3A T10A XLS602This is normal operation for your amp TroubleshootingSpecifications Dimensions Width Air Volume Requirements per minute per unitNet Weight Shipping WeightFacsimile Internet ServiceTechnical Support / Factory Service Year WarrantyWorldwide Except USA & Canada XLS Series Power Amplifiers Model Crown Factory Service Information

XLS 202 specifications

Crown Audio XLS 202 is a power amplifier that stands out in the pro audio market for its robust performance and versatile application capabilities. Renowned for its reliability, the XLS 202 is ideally suited for live sound, fixed installations, and portable systems. One of its most notable attributes is its power output, delivering up to 300 watts per channel at 4 ohms, which ensures that it can drive a wide array of speaker systems with confidence.

One of the key features of the XLS 202 is the inclusion of advanced technology such as the Integrated Protection Circuitry. This system safeguards the amplifier from potential damage caused by overheating, overloads, or short circuits. By automatically adjusting performance based on the current operating conditions, it ensures longevity and reliability, which is crucial for demanding environments.

Additionally, the XLS 202 employs a lightweight and compact design, utilizing a switch-mode power supply that not only reduces weight but also provides efficient power management. This feature is particularly advantageous for mobile sound engineers who need to transport their equipment regularly. The amplifier's high-frequency response and low total harmonic distortion ensure that audio fidelity is maintained, allowing for a clear and powerful sound output that performers and audience members alike can appreciate.

The XLS 202 is equipped with XLR, TRS, and terminal block inputs, facilitating easy integration into various systems. Moreover, it features a comprehensive set of control options, including independent volume controls for each channel, as well as a high-pass filter that can be adjusted according to user preferences. These controls allow sound engineers to tailor the audio to specific venues, resulting in optimal sound quality.

Furthermore, the XLS series amplifiers come with a durable, rack-mountable chassis, designed to withstand the rigors of touring and regular use. The intuitive LED indicators on the front panel inform users about the operational status of the amplifier, providing real-time feedback on performance.

In summary, the Crown Audio XLS 202 combines exceptional power, advanced protective technology, and user-friendly features within a rugged design, making it an ideal choice for professionals seeking reliable amplification in a diverse range of applications. With its balance of power, functionality, and durability, the XLS 202 continues to be a preferred option for those in the audio industry.
Top Page Image Contents