Troy-Bilt 643B Super Bronco manual Install Forward Clutch Cable

Page 7

I

The support brackets must be assembled to the outside of the handlebar assembly.

D

G

F

E

F

H

B

A

C

M

O

N

L

Fig. 2-3: Wheel in FREEWHEEL position (wheel drive pin through wheel shaft only).

STEP 4: INSTALL FORWARD CLUTCH CABLE

1.Carefully unwrap the forward clutch ca- ble (cable without an attached knob) from its shipping position and slide the thin ca- ble wire (M, Fig. 2-4) into the slot in the ca- ble bracket. Push the cable connector (N, Fig. 2-4) up through the hole in the bracket until the groove in the connector snaps into place.

2.Thread the #10-24 hex nut (Z, Fig. 2-5) halfway onto the screw (V) which runs through the spring (W, Fig. 2-5).

3.Thread the screw (V) into the cable ad- juster (X).

Fig. 2.2: Attach handlebar.

3.Slide the wheel fully inward on the wheel shaft (N, Fig. 2-3). Reinstall the wheel drive pin (M) through the wheel shaft only (not through the wheel hub). Secure the wheel drive pin with the hairpin cotter (L), pushing the hairpin cotter in as far as it will go. The wheel should now spin freely (freewheel) on the wheel shaft. Repeat with the other wheel.

4.Use the handlebar to roll the tiller to a flat area.

IMPORTANT: Before starting the engine, the wheels must be placed in the WHEEL DRIVE position (pins through wheel hubs and wheel shaft). This procedure is described in Wheel Drive Pins on page 10.

M

M

N

Fig. 2-4: Installing forward clutch cable bracket and cable.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 11/15/06 Form no -02357A.fmFinding Model Number Table of ContentsCustomer Support Do not put hands or feet near or under rotating parts Safety Alert SymbolCheck all nuts, bolts, and screws for Refer to the Maintenance sectionsKeep children and pets away Use slower engine speedsMaybeusedonthetillerandengine Operating SymbolsTo Avoid Serious Injury Inspect Unit AssemblyAssembly Steps IntroductionUse the handlebar to roll the tiller to a flat area Install Forward Clutch CableWith the Forward Clutch Bail Y, Fig While preventing the cable adjuster from turningCheck all nuts and screws for tightness Check Transmission OIL LevelFreewheel Ature package to identify the controls on your engineStop all tiller motion by releasing the Forward Clutch Bail Travel Position Shallow SettingsTo adjust the handlebars To operate the Forward Clutch BailChange engine oil Following steps describe how to start and stop the engineIntroduction BREAK-IN Operation Starting and StoppingTo move the Model 643C in reverse for short distances For forward motion of the wheels and power to the tinesOperating the Tiller Stopping the Engine and TillerTilling Tips & Techniques Read the following recommendations before tilling on slopes Tilling Tips & Techniques CON’TTilling On Slopes Clearing the TinesTerrace Gardening Loading and Unloading the TillerCheck Tire Pressure Transmission Gear OIL ServiceTiller Lubrication Check HardwareTine Inspection Removing⁄Installing a Single TineRemoving⁄Installing a Tine Assembly Bolo TinesReplacement Belt Information Checking and AdjustingTo Check Forward Belt Tension To Check Reverse Belt Tension Forward Clutch Bail AdjustmentEngine Cleaning AIR Cleaner Service Engine OIL Service Models 643B & 645A onlyTo Change the Engine Oil Spark Plug ServiceSpark Arrester Screen Service OFF-SEASON StorageProblem Possible Cause Correction TroubleshootingPage 643C, 643D 645A Description Models 643B, 643C, 643D & 645AGW-1224-3 Models 643B, 643C, 643D & 645A Models 643B, 643C, 643D & 645A 634-43203 Page Page TROY-BILT Tiller Lifetime Limited Warranty

643B Super Bronco specifications

The Troy-Bilt 643B Super Bronco represents a robust and versatile addition to the world of outdoor power equipment, designed with the needs of gardeners and landscapers in mind. This rear-tine tiller is a notable choice for those looking to cultivate their gardens efficiently and effectively.

One of the standout features of the Troy-Bilt 643B is its powerful 306cc OHV engine, which provides ample torque and ensures that the tiller can tackle tough soil conditions with ease. This engine is specifically designed for superior performance and reliability, allowing users to till effectively in a variety of soil types, from sandy loam to clay.

The tiller boasts a 12-inch tilling width and a tilling depth of up to 8 inches, making it ideal for preparing garden beds and landscaping areas. The adjustable tilling depth allows gardeners to customize their cultivation process, enabling them to penetrate deeper for planting larger crops or more shallow for seedbed preparation.

Equipped with a rear-tine design, the Super Bronco brings several advantages. The rear-tine configuration provides better control and stability while working, making it easier to maneuver in tight spaces. Furthermore, the counter-rotating tines help to break up compact soil while reducing the chances of soil clumping, resulting in a finer tilled surface.

Another remarkable feature is the Troy-Bilt patented "Smart Till" technology, which allows users to select the most suitable tilling method for their specific soil conditions. This innovative technology enhances efficiency, saves time, and ensures that the tiller delivers optimal results with every pass.

For ease of use, the tiller is equipped with large, easy-grip controls and a comfortable handlebar design that reduces fatigue during extended use. Additionally, the rugged construction and all-terrain tires enable the Troy-Bilt 643B to navigate challenging landscapes without issue.

The maintenance of the Super Bronco is user-friendly, with features that facilitate easy access to essential components for tune-ups and repairs. Overall, the Troy-Bilt 643B Super Bronco combines power, technology, and practicality, making it an excellent choice for both novice and experienced gardeners seeking to enhance their outdoor projects.
Top Page Image Contents