Troy-Bilt 630C Install Forward Clutch Cable, Use the handlebar to roll the tiller to a flat area

Page 7

K

 

 

G

H

 

I

A

 

 

F

 

 

 

 

G

 

 

E

F

C

 

 

 

 

 

J

D

 

 

 

 

B

Fig. 2.2: Attach handlebar.

M

O

N

L

Fig. 2-3: Wheel in FREEWHEEL position

STEP 4: INSTALL FORWARD CLUTCH CABLE

1.Carefully unwrap the forward clutch ca- ble (cable without an attached knob) from its shipping position and slide the thin ca- ble wire (T, Fig. 2-4) into the slot in the ca- ble bracket. Push the cable connector (U, Fig. 2-4) up through the hole in the bracket until the groove in the connector snaps into place.

2.Thread the #10-24 hex nut (Z, Fig. 2-5) halfway onto the screw (V) which runs through the spring (W, Fig. 2-5).

3.Thread the screw (V) into the cable ad- juster (X).

3.Slide the wheel fully inward on the wheel shaft (N, Fig. 2-3). Reinstall the wheel drive pin (M) through the wheel shaft only (not through the wheel hub). Secure the wheel drive pin with the hairpin cotter (L), pushing the hairpin cotter in as far as it will go. The wheel should now spin freely (freewheel) on the wheel shaft. Repeat with the other wheel.

4.Use the handlebar to roll the tiller to a flat area.

IMPORTANT: Before starting the engine, the wheels must be placed in the WHEEL DRIVE position (pins through wheel hubs and wheel shaft). This procedure is described in Wheel Drive Pins in Section 3.

T

T

U

Fig. 2-4: Installing forward clutch cable bracket and cable.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 11/19/03 Form no -10594D.fmFinding Model Number Table of ContentsCustomer Support Operation Safety Alert SymbolTraining PreparationUse slower engine speeds Maintenance and StorageExercise caution to avoid slipping or fall- ing Keep children and pets awayDecals Operating SymbolsTo Avoid Serious Injury Introduction AssemblyLoose Parts List Assembly StepsUse the handlebar to roll the tiller to a flat area Install Forward Clutch CableIf the spring length is incorrect, you While preventing the cable adjusterOutermost coil to the outermost coil From turningCheck all nuts and screws for tightness Check Transmission OIL LevelFreewheel Ature package to identify the controls on your engineStop all tiller motion by releasing the Forward Clutch Bail Travel Position Shallow SettingsTo adjust the handlebars To operate the Forward Clutch BailStarting and Stopping Introduction BREAK-IN OperationChange engine oil To move the Model 630C in reverse for short distances Operating the TillerStopping the Engine and Tiller For forward motion of the wheels and tinesTilling Tips & Techniques Tilling Tips & Techniques CON’T Power CompostingTilling On Slopes Loading and Unloading the Tiller Clearing the TinesCheck Tire Pressure Transmission Gear OIL ServiceTiller Lubrication Check HardwareTine Inspection Removing⁄Installing a Single TineRemoving⁄Installing a Tine Assembly Bolo TinesReplacement Belt Information Checking and AdjustingTo Check Forward Belt Tension To Check Reverse Belt Tension Forward Clutch Bail AdjustmentEngine Cleaning AIR Cleaner Service Engine OIL Service Models 634F/634A onlyTo Change the Engine Oil Spark Plug ServiceSpark Arrester Screen Service OFF-SEASON StorageProblem Possible Cause Correction TroubleshootingTROY-BILT Tiller Lifetime Limited Warranty
Related manuals
Manual 32 pages 56.08 Kb Manual 32 pages 63.05 Kb

634F, 630C, 634A specifications

The Troy-Bilt line of tillers, specifically the 634A, 630C, and 634F models, represents a blend of reliability, power, and advanced engineering designed to meet the needs of avid gardeners and professional landscapers alike. Each model boasts unique features and technologies that enhance performance and usability.

The Troy-Bilt 634A is equipped with a 6.5 HP engine, providing ample power for tackling tough soil conditions. The tiller's 16-inch tilling width allows for efficient breaking up of soil, while its impressive tilling depth of up to 8 inches ensures that garden beds are adequately prepared for planting. The 634A model features a lightweight design, making it easy to maneuver around flower beds and garden rows. Additionally, the adjustable handlebar enhances comfort during operation, accommodating various user heights.

In contrast, the Troy-Bilt 630C offers a slightly different approach. This model is designed for those who seek enhanced control and precision while tilling. It features a 6.75 HP engine and similar tilling capabilities but adds an innovative counter-rotating tilling technology. This feature is particularly useful for breaking up compacted soil and mixing in organic materials, resulting in a well-aerated and fertile garden bed. The 630C also comes equipped with a variety of attachments, allowing users to expand its functionality for different gardening tasks.

The 634F model elevates the line further with its robust frame and advanced features. With a powerful 7 HP engine, it provides optimal performance for larger plots of land. The 634F is designed with a wider tilling width of 18 inches, making it perfect for larger gardens and landscaping projects. Its self-propelled system allows for effortless movement across various terrains, reducing user fatigue. Additionally, the 634F includes a unique automatic depth adjustment feature, enabling gardeners to achieve the desired tilling depth without constant manual adjustments.

Across all three models, Troy-Bilt's commitment to user-friendly design shines through. Features such as easy-to-access controls, durable construction, and stable wheels enhance overall usability. The patented "Forward and Reverse" operating system found in these tillers ensures that gardeners can navigate easily in tight spaces, making them versatile for any gardening situation. The combination of power, advanced technology, and user-focused design makes the Troy-Bilt 634A, 630C, and 634F top choices for those looking to cultivate their garden with ease and efficiency.
Top Page Image Contents