Husqvarna 96093000901 owner manual Service and Adjustments, Tiller, Tire Care

Page 15

SERVICE AND ADJUSTMENTS

CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug.

TILLER

TO ADJUST HANDLE HEIGHT (See Fig. 20)

Select handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil.

•First loosen handle lock lever.

•Handle can be positioned at different settings between “HIGH” and “LOW” positions.

•Retighten handle lock lever securely after adjusting.

HANDLE

(HIGH POSITION)

HANDLE LOCK

LEVER

HANDLE

(LOW POSITION)

Fig. 20

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the custom- ers expense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/ DEPARTMENT, WHICH HAS THE PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.

TIRE CARE

CAUTION: When mounting tires, un- less beads are seated, overinflation can cause an explosion.

•Maintain 20 pounds of tire pressure. If tire pressures are not equal, tiller will pull to one side.

•Keep tires free of gasoline or oil which can damage rubber.

TO REMOVE WHEEL (See Fig. 21)

•Place blocks under transmission to keep tiller from tipping.

•Remove hairpin clip and clevis pin from wheel.

•Remove wheel and tire.

•Repair tire and reassemble.

CLEVIS PIN

HAIRPIN CLIP

Fig. 21

TO REMOVE BELT GUARD (See Fig. 22)

NOTE: For ease of removal, remove hairpin clip and clevis pin from left wheel. Pull wheel out from tiller about 1 inch.

•Remove two (2) screws from side of belt guard.

•Remove hex nut and washer from bottom of belt guard (located behind wheel).

•Pull belt guard out and away from unit.

•Replace belt guard by reversing above procedure.

BELT GUARD

SCREW

AND WASHER

 

HEX NUT AND WASH- ER (LOCATED BEHIND TIRE)

SCREW

HAIRPIN CLIP AND

AND

WASHER

CLEVIS PIN

Fig. 22

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents RTT900 Preparation Safety RulesMaintenance and Storage TrainingTable of Contents Assembly Tools Required for AssemblyOPERATOR’S Position See Fig Unpacking Carton See Fig Install Handle See Figs , 4,Check Tire Pressure Attach Clutch Cable See FigConnect Shift ROD See Fig Remove Tiller from CrateMeets Ansi Safety Requirements OperationKnow Your Tiller Reverse Wheels ONLY/TINES Stopped HOW to USE Your TillerTine Operation with Wheel Drive Forward Wheels ONLY/TINES StoppedFill Engine with OIL See Fig TurningTo Transport Before Starting EngineTo Start Engine See Fig ADD GasolineTine Shear Pins Tilling HintsCultivating Before Each USE MaintenanceLubrication Chart General RecommendationsEngine AIR Cleaner See FigSpark Plug CleaningCooling System See Fig MufflerService and Adjustments TillerTire Care To Replace Ground Drive Belt See Figs Ground Drive Belt Adjustment S e e FigTine Replacement See Figs , 25 Engine OIL StorageOther Fuel SystemTroubleshooting Points Handle Assembly Repair PartsMAINFRAME, Left Side KEY Part NO. NO. Description MAINFRAME, Right Side208cc Transmission19.5b Tine Shield      Tine AssemblyDecals Service Notes Warranty Statement
Top Page Image Contents