Test Drive and Braking, Test Limited Drive Speed

Second Edition • Second Printing	Operator's Manual

Test Drive and Braking

27Press and hold the function enable switch on the control handle.

28Slowly move the control handle in the direction indicated by the blue arrow on the control panel until the machine begins to move, then return the handle to the center position.

Result: The machine should move in the direction that the blue arrow points on the control panel, then come to an abrupt stop.

29Slowly move the control handle in the direction indicated by the yellow arrow on the control panel until the machine begins to move, then return the handle to the center position.

Result: The machine should move in the direction that the yellow arrow points on the control panel, then come to an abrupt stop.

Note: The brakes must be able to hold the machine on any slope it is able to climb.

Test Limited Drive Speed

30 Press the lift function select button.

31Press and hold the function enable switch on the control handle. Raise the platform approximately 1.2 m from the ground.

Result: The pothole guards should deploy.

FUNCTION TESTS

32 Press the drive function select switch.

33Press and hold the function enable switch on the control handle. Slowly move the control handle to the full drive position.

Result: The maximum achievable drive speed with the platform raised should not exceed 23 cm per second.

If the drive speed with the platform raised exceeds 23 cm per second, immediately tag and remove the machine from service.

Test the Tilt Sensor Operation

Note: Perform this test from the ground with the platform controller. Do not stand in the platform.

34Fully lower the platform.

35Place a 2x4 or similar piece of wood under both wheels on one side and drive the machine up onto them.

36Raise the platform approximately 2.1 m from the ground.

Result: The platform should stop and the tilt alarm will sound at 600 beeps per minute.

37Move the drive control handle in the direction indicated by the blue arrow, then move the drive control handle in the direction indicated by the yellow arrow.

Result: The drive function should not work in either direction.

38Lower the platform and remove both pieces of wood.

Part No. 82784

Genie GS-2032 and Genie GS-2632

GS-2632, GS-2032, 82784, CE specifications

The Genie GS series includes several electric scissor lifts, specifically the GS-1530, GS-1532, GS-1932, and GS-1930 models, designed for indoor use in various applications like construction, maintenance, and warehousing. Each model offers a robust set of features and technologies that cater to different working heights and space constraints.

The Genie GS-1530 is compact and ideal for navigating tight spaces, featuring a working height of up to 15 feet and a platform capacity of 500 pounds. It is equipped with non-marking tires, making it suitable for indoor operations without damaging floors. The GS-1530 is lightweight, allowing for easy transport and maneuverability, especially in crowded job sites.

The GS-1532 offers a slightly higher working height of 15 feet, with a larger platform that can accommodate up to 500 pounds. It includes an extension deck feature that provides additional workspace when needed, ensuring operational flexibility. Its narrow width and tight turning radius enhance its usability in constrained environments.

For users needing greater reach, the GS-1930 boasts a working height of up to 19 feet and a platform capacity of 500 pounds. It is designed with advanced battery technology for extended run times, enabling operators to work longer hours without needing a recharge. The GS-1930 can also quickly be transported between job sites or moved within larger facilities due to its compact design.

The GS-1932 further expands the capabilities with a larger platform and similar height of up to 19 feet. It features an innovative control system that allows for easy operation, even in complex settings. With its auto-levelling capabilities, the GS-1932 is equipped to handle uneven ground, making it versatile for various applications.

The CE versions of these models are tailored to meet European standards for safety and performance. They include features such as lowering speed control and emergency stop buttons, ensuring operator safety in various work environments. All models are designed with durability in mind and come with a range of maintenance-friendly features.

In conclusion, the Genie GS series showcases advanced engineering, user-friendly technology, and impressive lifting performance, making them suitable for a wide range of indoor applications. Their compact designs, combined with significant platform capacity, ensure that they meet the demands of modern workplaces. Whether for maintenance tasks or construction projects, the Genie GS models provide reliable solutions tailored to the needs of users.