Aqua Products AC-4000, AC-6000 Install t h e C e l l, Install t h e F l o w S e n s o r

Page 5

CONFIRM LAYOUT: Lay out equipment pieces to be sure there is enough pipe space between the last piece of apparatus and the tees in the return line to fit the Flow Sensor and the Cell. A Vertical installation may be used to save space (see diagrams above).

I n s t a l l t h e C e l l

1.The Cell and Flow Sensor must be installed downstream from the filter and heating devices but before any tees in the return line. The Cell may be installed horizontally or vertically so long as the Cell is pointed in the direction of flow and is installed immediately after the enclosed Flow Sensor (see diagram above).

2.Approximately 15 inches (~380 mm) of available pipe length will be needed for horizontal installations of the Flow Sensor and Cell. Vertical installations can be made to take less space.

3.On the pipe where the cell will be installed, mark two lines 11 3/4 inches (300mm) apart and cut out using hacksaw or pipe cutters.

4.Unscrew and remove the barrel unions (i.e. barrel nuts and slip connections) from either end of the Cell. Thread one of the barrel nuts over the pipe and glue its slip connection to the cut pipe.

5.Hold up the Cell with the second union to gauge the proper distance before threading the second nut and gluing the second slip.

6.After the glue had sufficient drying time, place the Cell with the o-rings into the opening between the two ends of the pipe and tighten the unions making sure that the Cell is installed with the arrow pointing in the same direction as the flow (i.e. water should enter from the side with the blue cap).

Flow direction

I n s t a l l t h e F l o w S e n s o r

1.Install the Flow Sensor between the last piece of apparatus and the Cell (if installed after the Cell, damage to the sensor may result). When possible, install on a horizontal pipe.

2.Mark two lines on the pipe 3 inches (~76 mm) apart and cut with a hacksaw or pipe cutters.

3.Clean and glue the “T” connector (included) to the pipe making sure that the threaded end with the sensor is on the topside of the pipe.

4.Be sure the arrow on the top of the Flow Sensor is pointing in the direction of flow, and that no glue touches the paddle inside the sensor as it may cause it to jam.

Flow direction

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Please Note Operation B L E O F C O N T E N T SRead and Follow ALL Instructions L C O M EAdditional Materials Required Safety MeasuresInstall t h e F l o w S e n s o r Install t h e C e l lU n t t h e C o n t r o l B o Flow sensor connectors Cell connectors Bonding Power CordPage Page R i n g t h e F l o w S e n s o r R i n g t h e C e l lDo Not Use A R T U PGallons Liters L I N I T Y D E M a N D T a B L EL b s Basic Operation E R a T I N G I N S T R U C T I O N S BackgroundN T R O L S Page I N T E N a N C E Cleaning With Optional Cleaning CapCell Maintenance Optional Cleaning Without Optional Cleaning CapSalt D E R S T a N D I N G T H E C H E M I S T R YPage 12.2 T U R a T I O N I N D EProblem Possible Causes What to do TroubleshootingCheck the Cell to ensure the blades are Not responding Ten 10 Year Limited Warranty BOX SYKESVILLE, MD

AC-6000, AC-4000 specifications

Aqua Products is renowned for its innovative pool cleaning solutions, and the AC-4000 and AC-6000 robotic pool cleaners are prime examples of the company's commitment to quality and efficiency. Designed for residential pools, these machines offer advanced technology that ensures a thorough clean with minimal user intervention.

The Aqua Products AC-4000 is specifically tailored for smaller to medium-sized pools, managing to deliver impressive cleaning capabilities without compromising on energy efficiency. One of its standout features is the Smart-Drive Technology, which utilizes a sophisticated algorithm to navigate the pool effectively. This ensures that every inch of the pool floor and walls are scrubbed, while avoiding obstacles along the way. Users appreciate the lightweight design of the AC-4000, which makes it easy to handle and store.

On the other hand, the Aqua Products AC-6000 is designed for larger pools, providing even greater cleaning power and efficiency. Its robust construction allows it to tackle tough grime and dirt. The AC-6000 is equipped with a powerful filtration system that captures debris as small as 2 microns, ensuring crystal-clear water. Its dual motor system enhances navigation, allowing it to cover various pool shapes and depths effortlessly.

Both models come with easy-to-use features, including programmable cleaning cycles and a convenient remote control for manual navigation. They are also equipped with a swivel cable to prevent tangling during operation, which is essential for maintaining optimal performance.

Moreover, Aqua Products emphasizes ease of maintenance across both models. The filter cartridges can be easily removed and cleaned, ensuring the robot maintains peak functionality. This hassle-free approach means more time enjoying the pool and less time worrying about cleaning.

Energy-efficient, both the AC-4000 and AC-6000 are designed to operate with minimal power consumption, keeping utility costs down while delivering exceptional cleaning results.

In summary, both Aqua Products' AC-4000 and AC-6000 robotic pool cleaners embody a perfect blend of efficiency, technology, and ease of use. Whether for small or large installations, these machines are tailored to meet the diverse needs of pool owners, ensuring a spotless swimming experience season after season.
Top Page Image Contents