Briggs & Stratton 30201 owner manual Assembly, Install Wheel Kit, Remove Generator From Carton

Page 6

PowerBOSS™

6200W Portable Generator

ASSEMBLY

 

 

 

ASSEMBLY

Your generator requires some assembly and is ready for use after it has been properly serviced with the recommended oil and fuel.

If you have any problems with the assembly of your

Generator and engine owner’s manuals

Engine oil

Wheel kit

Install Wheel Kit

generator, please call the generator helpline at 1-800-743-4115.

Remove Generator From Carton

1.Set the carton on a rigid flat surface.

2.Remove everything from carton except generator.

3.Open carton completely by cutting each corner from top to bottom.

4.Leave generator on carton to install wheel kit.

Carton Contents

Check all contents. If any parts are missing or damaged, call the generator helpline at 1–800–743–4115.

The generator

Figure 1 — Install Wheel Kit

NOTE: Wheel kit is not intended for over-the-road use. You will need the following tools to install these components:

1/2" or 13mm wrench

7/16" wrench

Socket wrench

1/2" or 13mm socket

7/16" socket

Pliers

Refer to Figure 1 and install the wheel kit as follows:

1.Tip generator so that engine end is up.

2.Slide axle through both mounting brackets.

3.Place a wheel on each side with air valve facing out.

Handle Pin

Nylon Washer

Nylon Washer

45 mm Cap Screw Flat Washer

Nut

Wheel

Handle

Use existing hardware to attach left side of support leg to unit

Nut

Flat Washer

Axle

20 mm Cap Screw

Vibration Mount

Support Leg

 

E-Ring

 

 

 

3/4” Cap Screw

Nut

6

Image 6
Contents Model / Modelo 030201 Table of Contents Safety RulesEquipment Description When Operating Equipment When Adding or Draining FuelWhen Starting Equipment When Transporting or Repairing EquipmentWhen Adjusting or Making Repairs to Your Generator When Testing for Engine SparkKnow Your Generator Carton Contents AssemblyInstall Wheel Kit Remove Generator From CartonAdd Engine Oil When Adding FuelBefore Starting the Engine Add FuelSystem Ground Using the GeneratorConnecting to a Building’s Electrical System Generator LocationStarting the Engine Connecting Electrical LoadsOperating Generator Do not Overload the GENERATOR. See Don’t Overload GeneratorStopping the Engine ReceptaclesCold Weather Operation 120/240 Volt AC, 30 Amp, Locking ReceptacleWind Capacity Power ManagementDont Overload Generator ExampleEngine Maintenance Generator Maintenance SpecificationsGeneral Maintenance Recommendations Generator CleaningStorage Generator StorageEngine Storage Other Storage Tips Troubleshooting Problem Cause CorrectionPowerBOSS Limited Warranty Reglas DE Seguridad Conserve Estas Instrucciones Tabla DE ContenidosDescripción DEL Equipo AdvertenciaCuando Opere EL Equipo Cuando Añada Combustible O Vacíe EL DepósitoCuando Ponga EN Funcionamiento EL Equipo Cuando Transporte O Repare EL EquipoPrecaución Cuando Ajuste O Haga Reparaciones a SU GeneradorCuando Pruebe LA Bujía DEL Motor Conozca SU Generador Tomacorriente Dobles de 120 Voltios AC, 20 AmpTomacorriente con Dispositivo de Seguridad de Contenido De La Caja MontajePara Retirar El Generador De La Caja Instale el Juego de RuedasAgregue Combustible Antes DE Darle Arranque AL MotorAgregar Aceite al Motor Cuando Añada CombustibleConexión al Sistema Eléctrico de un Edificio USO DEL GeneradorTierra del Sistema Ubicación del GeneradorConexion De Cargas Electricas Operando EL GeneradorEncienda el Motor No Sobrecargue EL GENERADOR.Vea No Sobrecargue GeneradorParado Del Motor Receptáculos PrecauciónOperación Durante UN Clima Frío Volt AC, 20 Amperios, Receptáculos DoblesFigura 15 Refugio Frío Permanente del Tiempo Control de la Energía No Sobrecargue GeneradorCapacidad EjemploMantenimiento del Motor EspecificacionesRecomendaciones Generales DE Mantenimiento Mantenimiento del GeneradorAlmacenando el Motor AlmacenamientoAlmacenando el Generador Otras Sugerencias Para el AlmacenandoProblemo Accion Causa Diagnositicos DE AveríasGarantía Limitada