Sears 536.9183 owner manual Carburetor Adjustment, IMPELLER!AUGER Control Cable Adjustment

Page 10

B. Leave wheel drive control lever in position where

neutral was obtained and release power cutch lever. Shut off engine.

C. Loosen screws in retaining bracket (figure 15)at top end of wheel drive control rod (under control panel).

D. Slide retaining bracket and rod left or right until

wheel drive control lever is in proper neutral

position. Tighten screws in retaining bracket.

E. Start engine and check adjustment by moving lever to each position, NOTE: Be sure to check to see that NEUTRAL is properly reached from both directions (from reverse and from forward gear).

POWER CLUTCH LEVER

RETAINING BRACKET

UPPER WHEEL DRIVE

CONTROL R_

pin through selector arm should engage wheel drive arm

only and clear impeller/auger drive arm by at least +/8 inch. To adjust to these positions:

A. Loosen screw that clamps impeller!auger control cable to cable bracket (figure 16).

B. Move cable forward or backward in clamp to obtain proper position mentioned above.

C. Reclamp cable by tightening loosened screw.

I

Never attempt

DANGER

A

turning,

I

 

to manually stop auger

from

 

CARBURETOR ADJUSTMENT

HIGH SPEED and IDLE ADJUST NEEDLES are pre+set at the factory and re-adjustmentshould notbe necessary. NOTE: If

you think the carburetor needs adjusting, contact your

nearest SEARS Service Center who has the proper

equipment and experience to make any necessary adjustments.

CAUTION

Never tamper with engine governor which is factory

set for proper engine speed. Over+speeding engine above factory high speed setting can be dangerous, If you think the engine governed high speed needs

adjusting, contact your nearest SEARS Service

Center who has the proper equipment and

experience to make any necessary adjustments,

Changing of engine governed speed will void engine warranty.

IMPELLER!AUGER CONTROL CABLE

ADJUSTMENT

If impeller/auger control should need adjustment because

impeller/auger wil! not engage or will not disengage, adjust as follows:

1. Remove belt cover (figure 11).

POWER CLUTCH CABLE

IMPELLER/AUGER

CONTROL CABLE

SCREW

CLAMP

CABLE BRACKET

SELECTOR ARM1/+INCH CLEARANCE

2. Move impeller/auger control lever from OFF to ENGAGE and check action of selector arm (figure 16). When

impeller/auger control lever is in ENGAGE position, pin through selector arm should fully engage wheel drive arm

and impeller/auger drive arm. When lever is in OFF position,

SPARK PLUG ADJUSTMENT

Check the spark plug periodically and reset spark plug gap to 0.030 inch using a wire feeler gauge.

The condition of the spark plug may be determined by color.

A carbonized plug is black and burnt plugs are greyish in

color, whereas a normal functioning spark plug is brown. If a new spark plug is required, refer to the Engine Repair Parts

section for proper replacement spark plug.

Before installing spark plug, coat threads lightly with graphite grease to insure easy removal.

DRIVE BELT REPLACEMENT

The drive belts on this unit are of special construction and

should be replaced with original equipment belts available from your nearest SEARS Store or Service Center.

To Replace Unit Drive Belt (belt nearest engine):

I. Remove belt cover (figure 11).

2+ Loosen screw holding left belt guide (figure 12) and swing guide away from pulley. Retighten screw.

3.Loosen screw holding right belt guide (figure 12) and swing guide away from puIley. Retighten screw.

4.Roll belt off engine pulley. NOTE: It will be necessary to

roll impeller/auger drive belt off engine pulley to allow unit drive belt to be removed from engine pulley.

5.Remove belt by threading up between large drive pulleys.

6.Install new belt in reverse order.

--10--

Page 9 Page 11
Image 10
Page 9 Page 11
Contents OWE Spark Plug Adjustment Impeller/Auger Control Cable AdjustmentCarburetor Adjustment Engine Service Operating ControlsWhen cleaning, repairing, or inspecting, make Stop engine whenever you leave the operatingHandle Assembly Contents of Shipping CartonTools Required for Assembly Controls AssemblyOx ,NcNsc LOW SEnING Operating ControlsOperating controls figures 8 & 9 and their functions are as Snow Thrower Operation Before Starting EngineRemove belt cover figure To Start EngineRunning Wheel Drive Control Adjustment Chute Deflector CableSpark Plug Adjustment Carburetor AdjustmentIMPELLER!AUGER Control Cable Adjustment Drive Belt ReplacementTransmission Replacement Shear Bolt ReplacementRoller Chain Replacement Snow Chain RemovalUnit Storage Engine ServiceEngine Storage Drain fuel into approved container outdoors, awayFor Service Helps Chart, see Craftsman 24 Snow Thrower Model Number 536,918300 No. Pa No Craftsman 24 Snow Thrower Model NumberKey 49551 122052 49106 49569 122033 996407 25644 49576 49557Craftsman 24 Snow Thrower Model Number Key No. Pa No 941353442619 49454 122119 68423 15316 48422 138538 35055 18 1O2883 Key No. Part No Descrip,tion51 \ Key No. Part No Craftsman 24- Snow Thrower Model NumberKey Craftsman 24 Snow Thrower Model Number Craftsman Snow Thrower Craftsman 4-CYCLE Engine MODEl. NUMBER143.696102 27882 27878A30826 Magneto Number 610694A 28545Number CarburetorRewind Starter Number Teeth Speed Transmission Model Number26 d Retaining27L Not remove carburetor bowl when the engine is hotUnit fails to discharge snow Replace defective plugYour Service HOW to Order Repair Parts

536.9183 specifications

The Sears 536.9183 is a versatile and reliable snow blower designed to tackle winter's toughest challenges. This machine is particularly noted for its robust build quality and user-friendly operation, making it an ideal choice for homeowners dealing with heavy snowfall.

One of the standout features of the Sears 536.9183 is its powerful engine. Equipped with a dependable gas-powered motor, it delivers ample horsepower that enables the snow blower to easily clear driveways, sidewalks, and patios. This engine is designed for efficient performance, proving to be fuel-efficient while still offering the torque necessary to navigate through dense snow and ice.

In terms of design, the 536.9183 showcases a well-thought-out structure that ensures durability and ease of use. It features a heavy-duty auger system made of steel, capable of breaking through hard-packed snow and ice. The auger effectively collects the snow and propels it through the chute, allowing for a clean and thorough clearing process. Additionally, the adjustable chute provides the flexibility to direct the snow away from the areas that have already been cleared, minimizing the effort needed to maintain a clear path.

The snow blower offers multiple speed settings, allowing users to navigate various conditions with ease. Whether tackling light, fluffy snow or heavier, compacted snow, the adjustable speed settings provide tailored performance. Moreover, the self-propelled function ensures that users can maneuver the machine effortlessly, reducing physical strain during operation.

Safety features are also a priority in the design of the Sears 536.9183. It comes equipped with user-friendly controls that are easy to understand and operate, ensuring that even novice users can handle the machine effectively. Additionally, the snow blower includes safety measures such as an emergency shut-off and a protective shield around the auger and impeller to prevent accidents.

In summary, the Sears 536.9183 stands out in the realm of snow blowers due to its powerful engine, durable construction, and thoughtful safety features. Its combination of efficiency, ease of use, and performance make it an excellent choice for homeowners looking to tackle winter's snow with confidence. As winter approaches, having the Sears 536.9183 ready to go ensures that homeowners can keep their pathways clear and safe throughout the season.
Top Page Image Contents