Sears 536.9183 Contents of Shipping Carton, Tools Required for Assembly, Handle Assembly

Page 4

CONTENTS OF SHIPPING CARTON

1 - 24 inch Snow Thrower (completely assembled except for handles, controls and headlight),

1 - Can of Engine Oil

1 - Upper Chute Control Rod

1 - Left Hand Handle Assembly

1 - Right Hand Handle Assembly (with clutch lever attached) I - Control Pane_ Assembly

1 - Bag of Assembly Parts Containing: I - 3A inch Flatwasher

2 - 5/16 inch Split Lockwasher

10 - Formed (curved) Washers

4 - No. 10 x 1/2 inch Hex Head Screws 4 - No. 10 Locknuts

2 - 5/16 x 5/8, inch Hex Head Screws

2 - 5/16 x 1 inch Hex Head Screws

8 - 5/16 x 13A inch Hex Head Screws

8 - 5/16 inch Locknuts

1 - 3/_ x 3A inch Hex Head'Screws

1 - 3_ inch Locknut

1 - Cable C_amp (meta!)

2 - Knobs (for Throttle and Impeller/Auger Drive Levers)

1 - Bag of Shear Bolt Replacement Parts (Not used in assem- bly) Containing:

3 - 5/16 x 13/_ inch Shear Bolts

3 - 5/16 inch Locknuts

I - Instruction Sheet

TOOLS REQUIRED FOR ASSEMBLY

1 - 3/8 inch Wrench (or adjustable wrench)

1 - 5/16 inch Wrench (or adjustable wrench)

2 _ V2 inch Wrenches {or adjustable wrenches)

2 - 7/16 inch Wrenches (or adjustable wrenches)

2 - 9/16 inch Wrenches (or adjustable wrenches)

1 - Hammer (plastic or rawhide head recommended)

Your Snow Thrower is right or left hand as you face the unit from operator position.

Figure 1 shows the Snow Thrower completely assembled. To

complete the assembly, proceed as follows:

POWER

CLUTCH LEVER

 

IMPELLER/AUGER

CONTRO.L

LEVER

RIGHT

 

 

 

HANDLE

LEFT HANDLE

 

 

 

,TTLE

CONTROL

LEVER

 

CHUTE

DEFLECTOR

LEVER

DRIVE coNTROL LEVER

CHUTE DEFLECTOR

PANEL

CABLE CLAMP

SIDE FRAME

_GAGE WHEEL

DANGER

The operation of any powered equipment can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety

glasses or eye shields while assembling or operating Snow Thrower.

HANDLE ASSEMBLY

Right handle has a lever (power clutch) attached to upper end. Nuts used to attach lower end of handles are attached to inside of side frame.

1.Attach right lower handle to side of side frame as shown in figure 2. Handle grip should be tilted down and out

when handle is properly installed.

"-

2. Repeat step 1 for left handle.

RIGHT HANDLE

 

FORMED WASHER

SIDE FRAME

 

 

 

 

5/16

x 1 INCH

SCREW

_

 

5/16

x % INCH

SCREW

 

L

 

5/,16

INCH

SPLIT LOCKWASHER

_

CONTROLS ASSEMBLY

1.Attach control panel to handles as shown in figure 3. NOTE: Attach panel with lower screw only on left side.

2.Attach chute deflector lever as shown in figure 3.

NOTE: Place a 5/16 inch flatwasher between lever assembly and handle at top screw position.

RIGHT HANDLE

CHUTE DEFLECTOR

CABLE BRACKET

CHUTE

DEFLECTOR

CABLE

BOTTOM

NUT

ONTROL

PANEL

TOP NUT

 

CHUTE

LEFT HANDLE

 

r

5/16 INCH

LEVER

FLATWASHER

All screws shown are 5/16

x 13,'inch.

All Iocknuts shown are 5/16 inch.

A formed washer is used on inside of handte at all screw locations.

3. To attach chute deflector cable bracket (attached to cable), proceed as follows:

A. Place chute deflector Iever in lowest (forward) notch.

B. Grasp chute deflector cable bracket and pull down until a 5/16 x 1_'_inch screw can be placed

through bracket and through left handle as shown in figure 3. NOTE: Only one of holes in cable bracket is large enough for mounting screw.

4.Cable length will need to be adjusted if chute deflector lever wilf not move all the way up to top notch in bracket or if

--4--

Image 4
Contents OWE Impeller/Auger Control Cable Adjustment Carburetor AdjustmentSpark Plug Adjustment Engine Service Operating ControlsWhen cleaning, repairing, or inspecting, make Stop engine whenever you leave the operatingContents of Shipping Carton Tools Required for AssemblyHandle Assembly Controls AssemblyOx ,NcNsc LOW SEnING Operating ControlsOperating controls figures 8 & 9 and their functions are as Snow Thrower Operation Before Starting EngineRemove belt cover figure To Start EngineRunning Wheel Drive Control Adjustment Chute Deflector CableCarburetor Adjustment IMPELLER!AUGER Control Cable AdjustmentSpark Plug Adjustment Drive Belt ReplacementShear Bolt Replacement Roller Chain ReplacementTransmission Replacement Snow Chain RemovalEngine Service Engine StorageUnit Storage Drain fuel into approved container outdoors, awayFor Service Helps Chart, see Craftsman 24 Snow Thrower Model Number 536,918300 Craftsman 24 Snow Thrower Model Number KeyNo. Pa No 49551 122052 49106 49569 122033 996407 25644 49576 49557Craftsman 24 Snow Thrower Model Number No. Pa No 9413534 42619 49454 122119 68423 15316 48422 138538 35055 18 1O2883Key Key No. Part No Descrip,tion51 \ Key No. Part No Craftsman 24- Snow Thrower Model NumberKey Craftsman 24 Snow Thrower Model Number Craftsman Snow Thrower Craftsman 4-CYCLE Engine MODEl. NUMBER143.696102 27882 27878A30826 Magneto Number 610694A 28545Number CarburetorRewind Starter Number Speed Transmission Model Number 26 dTeeth RetainingNot remove carburetor bowl when the engine is hot Unit fails to discharge snow27L Replace defective plugYour Service HOW to Order Repair Parts

536.9183 specifications

The Sears 536.9183 is a versatile and reliable snow blower designed to tackle winter's toughest challenges. This machine is particularly noted for its robust build quality and user-friendly operation, making it an ideal choice for homeowners dealing with heavy snowfall.

One of the standout features of the Sears 536.9183 is its powerful engine. Equipped with a dependable gas-powered motor, it delivers ample horsepower that enables the snow blower to easily clear driveways, sidewalks, and patios. This engine is designed for efficient performance, proving to be fuel-efficient while still offering the torque necessary to navigate through dense snow and ice.

In terms of design, the 536.9183 showcases a well-thought-out structure that ensures durability and ease of use. It features a heavy-duty auger system made of steel, capable of breaking through hard-packed snow and ice. The auger effectively collects the snow and propels it through the chute, allowing for a clean and thorough clearing process. Additionally, the adjustable chute provides the flexibility to direct the snow away from the areas that have already been cleared, minimizing the effort needed to maintain a clear path.

The snow blower offers multiple speed settings, allowing users to navigate various conditions with ease. Whether tackling light, fluffy snow or heavier, compacted snow, the adjustable speed settings provide tailored performance. Moreover, the self-propelled function ensures that users can maneuver the machine effortlessly, reducing physical strain during operation.

Safety features are also a priority in the design of the Sears 536.9183. It comes equipped with user-friendly controls that are easy to understand and operate, ensuring that even novice users can handle the machine effectively. Additionally, the snow blower includes safety measures such as an emergency shut-off and a protective shield around the auger and impeller to prevent accidents.

In summary, the Sears 536.9183 stands out in the realm of snow blowers due to its powerful engine, durable construction, and thoughtful safety features. Its combination of efficiency, ease of use, and performance make it an excellent choice for homeowners looking to tackle winter's snow with confidence. As winter approaches, having the Sears 536.9183 ready to go ensures that homeowners can keep their pathways clear and safe throughout the season.