Poulan 96192001801, 415244 owner manual Storage, Other

Page 17

SERVICE AND ADJUSTMENTS

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex- haust area is still warm.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEYDischarge chute control lever used to change the di Meets A.N.S.I. Safety RequirementsRecoil auxiliary starter handle used for starting Stopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Start Engine Before Starting the EngineScraper BAR If Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Engine CleaningChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Other StorageTroubleshooting Service Notes 1958 405972X479 405973X479Page 414280 Knob, Lever Repair Parts Snow Thrower Model PP10530ES Handles 17060410 Repair Parts Drive Repair Parts Snow Thrower Model PP10530ES Drive Page 35062 KEY Part DescriptionRepair Parts Wheels / Decals 415244 415245 Wheels / DecalsLimited Warranty

96192001801, 415244 specifications

The Poulan 96192001801,415244 is a noteworthy option in the realm of outdoor power equipment, specifically designed for lawn care enthusiasts and professionals alike. This product stands out for its robust features, innovative technologies, and user-friendly characteristics that enhance lawn maintenance experiences.

One of the main features of the Poulan 96192001801,415244 is its powerful engine. Equipped with a reliable two-cycle engine design, it delivers robust performance, ensuring that users can tackle various lawn care tasks with ease. The engine provides sufficient power for trimming, edging, and even light landscaping, making it a versatile tool for yard maintenance.

The lightweight design of this product significantly enhances user comfort and maneuverability. Weighing in at a manageable level, the trimmer allows for extended use without causing undue strain on the user. This aspect is particularly beneficial for homeowners who may need to spend several hours working on their lawns or for professionals who require efficiency and ease of use.

Additionally, the Poulan 96192001801,415244 features an adjustable cutting width, allowing users to customize the trimmer’s performance based on specific needs. This flexibility not only increases efficiency but also saves time, as users can switch between different tasks without the hassle of changing equipment.

An important characteristic of this model is its ease of starting mechanism. The inclusion of an easy-start system minimizes the effort needed to get the trimmer up and running, thus reducing frustration, especially on busy days when tackling multiple gardening tasks. This feature is particularly appreciated by novice users who may lack extensive experience with outdoor power equipment.

The Poulan 96192001801,415244 also incorporates a straightforward line feed system, which ensures that users can quickly and efficiently replace the cutting line when needed, minimizing downtime during yard work. This design consideration makes it an excellent choice for those who prioritize efficiency and convenience.

In summary, the Poulan 96192001801,415244 combines power, versatility, and user-friendly features, positioning it as a top-tier option for anyone looking to maintain their outdoor spaces effectively. Whether for residential use or professional landscaping, this trimmer provides the functionality and reliability needed for successful lawn care endeavors.
Top Page Image Contents