Poulan 96192004200 Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 15

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or ad- justments:

1.Be sure the on/off switch is in the OFF position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

To replace the capscrew/shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 18)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a shear bolt and hex nut. Should a foreign ob- ject or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shear bolt. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are designed to break, preventing damage to any other com- ponents. If impeller does not turn when auger control lever

is engaged, check to see if the capscrews have sheared. 15

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

1/4-20

1/4-20 x 1-5/8

1/4-20 x 2

LOCKNUT

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

IMPELLER HUB

 

 

IMPELLER

 

 

SHAFT

 

 

 

AUGER

 

 

HUB

1/4-20

 

 

LOCKNUT

AUGER HUB

AUGER SHAFT

FIG. 18

TO REMOVE BELT COVER (See Fig. 19)

1.Remove the two (2) screws securing belt cover to frame.

2.Remove belt cover.

3.Replace belt cover by installing cover and screws and tighten securely.

BELT

COVER

FRAME

SCREWS

FIG. 19

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerElectric start button used for starting the engine Meets A.N.S.I. Safety RequirementsTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See FigUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Before Starting the Engine If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Exploded KEY Part Description Scrapper BAR Auger HousingAuger Assembly LH Auger Assembly RHSkid Plate RH Auger BearingBearing Plug Skid Plate LHPlastic Washer Knob BlackPOP Rivet WasherRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldRepair Parts Snow Thrower - Model Number PR624 Handles 419797X431Lower Handle Handle Knob SpacerRetainer Knob REDShifter ROD Bottom Impeller RODTraction ROD Shifter ROD TOPTorsion Spring Console PanelInterlock Spring Interlock CAMRepair Parts Snow Thrower - Model Number PR624 Drive Rubber Ring AssemblyDrive Plate Assembly Speed SelectorClik PIN Axle ShaftRoll PIN 3/16 SprocketEngine Mounting Plate Complete LCT EngineFrame 427963X421Idler Pulley Impeller BeltTraction Belt Idler ARM Bracket432332X428 Repair Parts Snow Thrower - Model Number PR624 WheelsWheel Assembly LH 432331X428Safety Ignition KEY Snow Thrower - Model Number422663 Repair Parts Snow Thrower - Model Number PR624 Decals 181037DECAL, Danger Service Notes Service Notes Limited Warranty

96192004200, 436132 specifications

The Poulan 436132,96192004200 is a reliable chainsaw designed to cater to both novice users and professionals alike. Known for its robust performance and user-friendly features, this chainsaw stands out in a crowded market, making it a preferred choice for those tackling various tasks, from tree trimming and yard work to more intricate woodcutting projects.

One of the main features of the Poulan 436132 is its powerful engine. With a displacement of 42cc, the chainsaw delivers sufficient power to handle demanding cutting tasks with ease. This convenient combination of power and efficiency allows users to cut through dense wood without experiencing any significant loss of performance. The engine's design promotes fuel efficiency, ensuring that operators can work longer without frequent refueling.

The Poulan 436132 is also equipped with a lightweight construction, which significantly enhances user maneuverability. Weighing just under 10 pounds, this chainsaw reduces fatigue during extended periods of use, making it suitable for larger projects without compromising comfort. The ergonomic handle design further contributes to user comfort, allowing for a secure grip that minimizes vibrations, thus enhancing control and precision.

Safety is a critical aspect of chainsaw design, and this model does not disappoint. It incorporates a chain brake system that halts the chain's motion in the event of kickback, protecting the user from potential injuries. Additionally, the tool includes a throttle lock, which prevents accidental starts, adding an extra layer of security for novice users.

The chainsaw features an automatic oiling system that keeps the chain lubricated, reducing wear and tear while ensuring smooth operation. This system fosters reduced maintenance needs, enabling users to focus more on their projects rather than spend time on upkeep.

Another notable characteristic is the easy access to the air filter and spark plug, simplifying maintenance tasks. This intuitive design allows users to keep the chainsaw in top condition without requiring specialized tools or extensive mechanical knowledge.

In summary, the Poulan 436132,96192004200 is a versatile and dependable chainsaw that fuses power, comfort, and safety. With its user-friendly features and advanced technologies, it remains an excellent choice for those in search of a reliable cutting tool to assist in various woodwork tasks and yard maintenance. Whether for light-duty or more demanding applications, this chainsaw is engineered to deliver consistent performance with every use.
Top Page Image Contents