Poulan 436132, 96192004200 owner manual To Replace Belts See Fig

Page 16

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 20)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a service center/department.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construc- tion and should be replaced by original equipment manu- facturer (OEM) belts available from your nearest service center/department. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/ or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding the auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE HAIRPIN FROM CLUTCH ROD and re- move clutch rod from swing plate. Tip swing plate forward.

7.REMOVE AUGER BELT from around pulley.

8.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

9.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

10.Install clutch rod in swing plate; secure with hairpin.

11.Place auger belt around and inside the groove of auger pulley only.

12.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

13.Move idler arm so it does not hit impeller pulley as you bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 12. Belt must be fully seated in pulley groove when bringing the snow thrower together.

14.Install the two (2) hex bolts and tighten securely.

15.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

16.INSTALL BELT COVER and two (2) screws. Tighten securely.

17.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

 

TRACTION DRIVE BELT

 

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

 

BOLT

 

IDLER ARM

 

AUGER

SQUARE

 

BELT

HOLE

 

 

 

CLUTCHING

 

 

 

IDLER ARM

 

 

 

BRACKET

 

 

FRAME

AUGER PULLEY

AUGER

HOUSING

 

 

 

BOLTS

 

16

FIG. 20

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Electric start button used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Before Starting the Engine Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Exploded KEY Part Description Auger Housing Auger Assembly LHAuger Assembly RH Scrapper BARAuger Bearing Bearing PlugSkid Plate LH Skid Plate RHKnob Black POP RivetWasher Plastic WasherLEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator Head419797X431 Repair Parts Snow Thrower - Model Number PR624 HandlesLower Handle Spacer RetainerKnob RED Handle KnobImpeller ROD Traction RODShifter ROD TOP Shifter ROD BottomConsole Panel Interlock SpringInterlock CAM Torsion SpringRepair Parts Snow Thrower - Model Number PR624 Drive Assembly Drive Plate AssemblySpeed Selector Rubber RingAxle Shaft Roll PIN 3/16Sprocket Clik PINComplete LCT Engine Frame427963X421 Engine Mounting PlateImpeller Belt Traction BeltIdler ARM Bracket Idler PulleyRepair Parts Snow Thrower - Model Number PR624 Wheels Wheel Assembly LH432331X428 432332X428Snow Thrower - Model Number Safety Ignition KEY422663 181037 Repair Parts Snow Thrower - Model Number PR624 DecalsDECAL, Danger Service Notes Service Notes Limited Warranty

96192004200, 436132 specifications

The Poulan 436132,96192004200 is a reliable chainsaw designed to cater to both novice users and professionals alike. Known for its robust performance and user-friendly features, this chainsaw stands out in a crowded market, making it a preferred choice for those tackling various tasks, from tree trimming and yard work to more intricate woodcutting projects.

One of the main features of the Poulan 436132 is its powerful engine. With a displacement of 42cc, the chainsaw delivers sufficient power to handle demanding cutting tasks with ease. This convenient combination of power and efficiency allows users to cut through dense wood without experiencing any significant loss of performance. The engine's design promotes fuel efficiency, ensuring that operators can work longer without frequent refueling.

The Poulan 436132 is also equipped with a lightweight construction, which significantly enhances user maneuverability. Weighing just under 10 pounds, this chainsaw reduces fatigue during extended periods of use, making it suitable for larger projects without compromising comfort. The ergonomic handle design further contributes to user comfort, allowing for a secure grip that minimizes vibrations, thus enhancing control and precision.

Safety is a critical aspect of chainsaw design, and this model does not disappoint. It incorporates a chain brake system that halts the chain's motion in the event of kickback, protecting the user from potential injuries. Additionally, the tool includes a throttle lock, which prevents accidental starts, adding an extra layer of security for novice users.

The chainsaw features an automatic oiling system that keeps the chain lubricated, reducing wear and tear while ensuring smooth operation. This system fosters reduced maintenance needs, enabling users to focus more on their projects rather than spend time on upkeep.

Another notable characteristic is the easy access to the air filter and spark plug, simplifying maintenance tasks. This intuitive design allows users to keep the chainsaw in top condition without requiring specialized tools or extensive mechanical knowledge.

In summary, the Poulan 436132,96192004200 is a versatile and dependable chainsaw that fuses power, comfort, and safety. With its user-friendly features and advanced technologies, it remains an excellent choice for those in search of a reliable cutting tool to assist in various woodwork tasks and yard maintenance. Whether for light-duty or more demanding applications, this chainsaw is engineered to deliver consistent performance with every use.
Top Page Image Contents